I am developing an assembly, however it needs to move a cylinder to find a specific surface.
How do I determine through simulation that dynamic surface will collide with one another?
Motion to hydraulic cylinder in dynamic simulation
I'm trying to find the intersecting points of a part that connects to the outside surface of a cylinder shaped part.
What is the best way to go about this? I have attached some images that hopefully illustrate my problem.
I have unchecked resolve file references, etc, and still basically spends 5 minutes looking for files i told it not to look for. Why doesnt it just open the assembly or drawing, without waiting for ever?
View 3 Replies View RelatedI would like to know how can put planar surface to solid object which surface is curved like cylinder for example. When start draw from first point rectangle of planar surface follow x cordinate not that solid object. How to do that simply?
View 9 Replies View RelatedIn inventor 2013 I want to extrude a horizontal circle on surface of a bigger vertical hollow cylinder. but what i did it enters into cylinder, and i only want to extrude it on external surface.
View 1 Replies View RelatedIV 2011.
I have an assembly with a FEA simulation result. I can run a report and get the reaction forces and moments at each constraint. I would like to run a new simulation with different constraints and use the reaction results from the first simulation as loads in the second one.
Currently I do this by running a report on the 1st simulation to get a table of the reaction results. I then manually add those forces to the 2nd simulation. This takes time to type and the forces must be edited each time I re-run the 1st simulation.
Is there a way to use parameters to automate this?
when I try to use rulesurf between 2 circles on an angled plane, the surface twists instead of drawing a cylinder.
View 2 Replies View RelatedI am working on the attached file. I need to either subtract or surface trim the corners of the cylinder but when I try to do either some other surfaces that i did not select get trimmed. 6.dwg
View 4 Replies View RelatedI have an assignment. I've done all the work until i reached the end of it which is adding 2 cylinders to a weird looking object.
I'm trying to put the cylinder which shares a space between a wedge and a region but I'm unable to subtract it.
I've never worked with 3D effect before (not even in the earlier versions), until now when I finally need it. I've therefore searched the Internet and the Adobe Forums in order to get to know how to wrap a text/image around a glass bottle in Photoshop CS6. I've found several answers and tutorials, but none of them regards CS6 or they are simply too primitive, whereby the effect is too fake. But when I try follow the instructions in the explanations/tutorials I've found so far for earlier versions of Photoshop (especially regarding 3D effects), I can't find the right buttons, commands, etc. - I can't make it work. how to do wrap a text/image around a bottle/cylinder/object in Photoshop CS6?
View 7 Replies View RelatedMH.dwg
I'm trying to slice the grey cylinder object in the attached drawing with a curved network surface. Rather than slice around the path of the surface it seems to have just taken a planar slicing plane between the 2 vertical edges of the network surface.
I want to wrap label on the cylindrical shape object.
[URL]
i need to flatten the semi cylinder into planer surface...is there any modifier to do this...also i described exact need in the attached image..
View 8 Replies View RelatedWhen trying to move to an object to a specific coordinate autocad2012 puts @ in automatically. How setvar do i use to remove this unnecesarry hurdle
View 1 Replies View RelatedI am using Civil 3D 2011 and wondering how to create just one contour on an existing surface at a specific elevation. I need to show where floodwaters would get to at a specific elevation so that contour would be the easiest way if I can contour the surface with just 1 elevation. I don't want to have to create 0.1' contours all over the site and then remove all the extras.
View 8 Replies View RelatedI have a 100 acre park that I am doing earthworks. I have 1 proposed and 1 existing surface. The park is now broke into 5 different areas and I need to get cut and fill for each area. Is there a way to do a volume report for a particular area? I could define the area with a polyline. Or do I need to copy the proposed surface and start chopping up into 5 areas?
View 9 Replies View RelatedI have created a surface spot elevation label style. I have several surfaces. How do I associate the style with a specific surface?
View 2 Replies View RelatedI am curious if it is possible to modify only specific portions of a surface? For example, I have recieved an xml surface representing FG for a project, and want to do an earthwork calculation, could I raise and lower only portions of the project say by using specific boundaries for the asphalt paving, concrete etc. and then implement the raise & lower surface feature for these portions of the FG surface.
At this time I have been creating multiple surfaces for each particular feature of the site, then paste the FG surface, add a boudary and lower appropriately. Finally, I have to go through and paste each particular feature and its small surface into one "subgrade surface" to get an accurate representation. This method results in countless small surfaces and alot of leg work for something that seems like it should be simple.
I know that the surface defentions (FL's or corridors), should they be provided, would make this easy, but there have been several occasions where these are not being made availble by the project sponsor.
I created surfaces in Civil 3d 2011 for existing and proposed and I did a surface volume between them. Is it possible to create a specific contour in the volume surface that represents the fill volume elevation (daylight line I think)? My proposed surface is a flood water elevation and I need to define the boundary at that elevation.
View 3 Replies View RelatedI followed the steps I found online to create color-specific surface labels (I assigned red to the cut elev and green for the fill elev.), but when I display them using the spot elevation on grid, I am getting both red and green elevations on same point (they are both fill elev or cut elev.), and why are there two elevations (cut-red and fill green) displaying?
View 9 Replies View RelatedRE: Autocad LT not able to move an entity along a line a specific distance using cursor snap and dynamic input
What I want to do is move a line on an angle a certain distance in the direction of the line itself in this case 20mm
What used to happen is you'd simply select move and an endpoint on the line then hover over the mid or opposite endpoint of the line and enter 20 and it would move 20mm along the trajectory of the line.
The same set of actions now only seem to allow you to move the entity 100mm (the default value) along itself in the correct direction. If you enter 20 it does not move and if you enter 50 it moves 100!
Is there a way for Civil3D to create/generate/extract a contour of a specific elevation such as 105.53 from an existing surface?
View 4 Replies View RelatedI use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.
I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.
I've had a simple lisp I've been using for years that suddenly disappeared. It required that you identify a block name, tag name, and the value that you want the tag to be. All of this is performed via command line, so it is scriptable. Since I lost it, I've been experimenting with -attedit. This command comes frustratingly close to what I'm looking for, except it only appends an existing tag, or replaces a specific string within the tag; I can't get it to replace the entire tag, regardless of its value.
1> Any lisp routine that does what I describe?
or
2> How to make -attedit replace a tag value without regard to what the value currently is (like a * wildcard)?
I am creating a chrome emblem using Photoshop's CS6's 3D tool. On the face of the surface I want a specific reflection (an image of city street with people walking, etc.). I want to be able to control this reflection by moving it around on the surface so I can control what is reflecting.
View 5 Replies View Relatedi'm looking for a Pantone color, that has this code "PMS 583 C", i tried typing it in the Pantone Solid Coated library searchbar but i couldn't find it. does it have a different code or something, the color is greenish.
View 3 Replies View RelatedI am looking for an alternative to in place XRef Edit.
The third party software I am stuck with has disabled in place editing an Xref.
The specific application I need is to allow the user to move an intelligent room tag that is XReffed into discipline specific models. Disciplines are Architectural, Mechanical, Electrical..Etc. Each discipline has their own room tag and needs to move their own tag to a location that can be clearly seen on their finished plot. Xref edit in place is the perfect tool for this..But since the third party has disabled the command, I need an alternative method.
where i can find the surface finish symbol in autocad 2009 ?
sym06.png
I've created a successful FEA simulation in Inventor 2014 and obtained results. But I want to see the highest stress in a defined area that is smaller than the entire part (I have some stress concentrations that are throwing off my 'max'). Is there a way to probe an area instead of just a point? I'm tired of creating a dozen probes to find the 'local max'.
View 8 Replies View RelatedHow to create or how to set a one way rotation joint as a one way bearing will work on real life, is this possible?
View 9 Replies View Related
