AutoCAD Inventor :: Hose Fitting Authoring
Jan 10, 2012
I downloaded a hose fitting ipt file from the Parker website and did the Tube and Pipe Authoring thing to put it into the content center as a new family in a new read/write library. When I browse for it to use as the Start Fitting on my hose, the new family does not appear in the list. What is my problem?
The new library is checked in my Projects configuration. I have been monkeying with the NS column of the family and can't seem to get it back to its original format now.
View 8 Replies
ADVERTISEMENT
Nov 11, 2011
I had a hydraulic hose connected to an elbow fitting and now it has been changed a straight fitting.
What is the proper way to do this so that it is still adaptive?
And how can I reconnect the hose to the new fitting and have it adaptive?
View 2 Replies
View Related
Jul 16, 2010
Using Routed Systems in the Tube & Pipe Authoring dialog page on the End Treatment pull down -- is there a detailed list of what the different end treatments mean ? such as what does "Quick Connect" exactly mean, or Swaged, single ferrule or dual (such as used with a Swagelok fitting)... What can you do with "Other".... etc..
View 9 Replies
View Related
Dec 4, 2012
I'm putting flexible hoses in an assembly and need to use a few different sizes. So I create run1 and set the hose to be 1/2" hose. Then I create a run2 and change the hose size to 1/4" but it also changes the size of the hose in run1. Is this supposed to happen? How can I get two different sizes of hose?
I've just been going down to the sweep feature which makes the hose and adding dimensions to the ID and OD so I can control the size. This is a pain and doesn't seem like what should need to be done. Is there a way to have different hose runs be different sized hose?
View 9 Replies
View Related
Dec 4, 2005
I need to model up a convoluted flexible hose as a component part for use in an assembly. What is the best approach to creating this with a realistic and natural look?
View 9 Replies
View Related
Jun 11, 2012
How would you draw a spiral garden hose? If you don't know what i mean by spiral garden hose Google it. How would you draw the hose.
And would it be possible to make it flexible?
View 9 Replies
View Related
Jul 30, 2013
I need to make a 1/8" diameter flexible hose, but the sizes listed for the Parker Hydraulic Hose only go down to 1/4". The closest solution I could find is here:
[URL]........
Here is what I did:
In my assembly, click "Place From Content Center"
Find "Parker Hydraulic Hose"
When I right click on it, the only selection is "Add to Favorites"
Double click on "Parker Hydraulic Hose"
Go to "Table View" tab
Right click on a row, but there is no "Input" selection.
View 5 Replies
View Related
Feb 1, 2013
How can i increase the size of the hose beyond 2" max that Pipe&Run allows it to be? I need the hose more for a visual rather then its acual function. I'm guessing i gonna have to change its paremeters right? if so, how do i and what needs changed?
View 1 Replies
View Related
Dec 30, 2010
I created a structural shape profile for use in a project. It is square tube with radiused corners, very similar to "ANSI/AISC (Rolled Steel) Structural Tubing Square" in the content center, but mine is 1 inch square with 0.065 inch walls.
I've made a chassis out of my custom tubing. When I run a frame analysis on it, I get an error/warning stating that the torsional section modulus is zero, because I didn't fill in the value when I generated the frame. How do I calculate that value?
I've attached the tube that I used to make the structural shape.
View 9 Replies
View Related
Dec 16, 2011
I have authored a part to the Content Center, but the part is inserted at a standardized length. How do I author the part so that the length can be specified whem inserted, like the structural steel shapes?
View 3 Replies
View Related
Aug 29, 2012
I have a couple of users who accidently added connections to the wrong parts and made them fittings.
For the life of me I cannot remember how to turn them back into regular Inventor parts.
I've removed the connection points, but the parts still appear as fittings when placed into an assembly.
Inventor 2012 SP3 ~ Vault Pro 2013
Lenovo D20 Workstation Intel Xenon E5640@2.67GHz (2)
Win 7, 24gb RAM, NVIDIA Quadro FX 3800
View 8 Replies
View Related
Feb 28, 2013
I'm trying to make a piping run that at one point branches off in another direction. Basically I want to have one straight pipe, a main line, where another pipe branches off and sticks out vertically from it and goes its own way. However, I want this branching pipe to be welded to the main line, not connected with a tee fitting. Inventor won't let me create branches from within a route, and it doesn't seem to want to let me snap to the existing main line run if I create a new run for the branching pipe.
View 5 Replies
View Related
Aug 4, 2012
I am trying to create a flexiable hose, i dont want it to move or anything. I have tried to sweep a circle along the path, but my pline is not on a coplanar line so that makes it difficult. tried using extrude. tried using a helix but can't get the right angles.
View 9 Replies
View Related
Mar 8, 2012
If it is possible to set a fixed length to a "Hose" hanging from one point to another? So that when hang-off point's are adjusted (any direction) the hose act pursuant to the fixed length.
View 9 Replies
View Related
Oct 30, 2012
Where is Block Authoring Palette in 2013?
I want to make dynamic block...
But i couldnt find Block Authoring Palette to parameters...Actions....
I am using AutoCAD 2013 for Mac as students lisence.
View 5 Replies
View Related
Jan 12, 2012
I am a new user and working my way through the AutoCad Training Guide AutoCad LT 2012 No Experience Required. In Chapter 9 is Creating a Dynamic Block. After creating a block and inserting it into a new drawing you are able to open the block editor and begin using the Authoring Palettes. In my case the Authoring Palettes are blank except for a a blank Create a New Palette.
Under the Palette's Properties All Palettes are checked as on. How do I turn on the ones shown in the book? Constraints, Parameter Sets, Actions, and Parameters.
View 4 Replies
View Related
Mar 15, 2011
I have ACA 2011 on 64 bit Windows 7. I can't seem to find the block authoring palette anywhere..
View 2 Replies
View Related
Oct 10, 2011
when im switching my drawing into paper space and then trying to print it my drawing is massive and only small part of it id in the peper space.
View 9 Replies
View Related
May 14, 2011
I am relatively un-practiced using AutoCAD and I am struggling with keeping my drawing in the state it was created. All of my curved lines seem to have moved or doubled so now there are two of the same very close to each other which makes the line width seem heavy. Because my curved lines are not exactly where I created them now it means that my hatching does not sit flush with its boundary. A separate issue is that when I am choosing 'pick points' to hatch, they take a very long time to select before the hatch box appears.
View 4 Replies
View Related
Nov 19, 2012
I have a sinusoidal curve, that I've created using a third party app, which has worked really well. But the app only produces the form in a straight line and i now need to fit it to a number of curves.
I have a form of 3 radii and a couple of flats, which the sinusoidal form needs to fit along. All this work is just in 2D as i need to output the dxf into a CNC machine.
View 3 Replies
View Related
May 30, 2013
Longtime C3D user, new to pressure pipes though. It seems one cannot mask pressure fittings in plan view. Is that correct?
Using C3D 2014
View 2 Replies
View Related
Jan 30, 2013
I am trying to add geometry programatically to a duct fitting. This is because the content builder is incapable of correctly building some types of fittings. I found some old code from an Autodesk University class that shows how to add geometry to a AEC object. I have modified it a little to be able to work with a duct fitting but it does not work. The code compiles fine and runs fine without any errors. The geometry is just not added.
[CommandMethod("ACAClassCode", "ExModelerModifyBody", CommandFlags.Modal)] public void ModifyBody() { Database db = HostApplicationServices.WorkingDatabase; Editor ed =
[Code]....
View 1 Replies
View Related
Aug 23, 2013
I've just got AutoCAD 2012 and mkaing some rings, I needed to fit the same textures of a ring of 8mm in a 6mm ring. My problem is that the inside diameter is larger in the 6mm ring, and that's why I can't use the Scale command. Is there a command that allows me to fit all the objects in this area??
Here is the file with both of the rings.
View 2 Replies
View Related
Jan 18, 2012
Pipe and tank plant layouts, now need to make a modified (not standard) pipe fitting.
Looking for a pipe plug drawing. the fitting (Imperial) is 4—10. Four inch NPT piping. Appears to have a slight taper, very slight.
Or, better yet, a G 3-3/4" pipe thread(?).
a *.dwg (AutoCAD 2007) drawing?
View 7 Replies
View Related
Sep 14, 2012
Put together a pressure network and actually plotted it out for a project? Are the fittings and appurtenances even readable? I have a network setup on 40 scale plans and when plotted out, you can't even tell what a recuder is compared to a valve. Tees are obvious but thats only because of the branch pipe coming off of it. Our company uses the old basic symbols that are blown up big enough that dimensionally, they are not correct but visually they look really nice.
View 9 Replies
View Related
Sep 11, 2013
I am designing pressure pipe network for water supply line in civil 3d 2013.In that ,I am not able to insert 90 degree bends,change pipe properties know that there is default bends available in civil 3d but I need more fittings and different dia pipe. I asl know that in C:program dataAutodeskenupressure pipe fittings in that all fittings are available and SSL there is .*sqlite file available. But I Don't know to how to import this pipe fittings in civil 3d 2013.
View 3 Replies
View Related
Mar 19, 2010
Corel have just released the alternative authoring module for X3, in response to our complaints about the existing one. It is in fact a reworked version of Movie Factory 7 Pro, but now has the SE (Special Edition) letters worked into its title.
I have been one of the lucky people who have had the full version of MF7 since its original limited release. (For some unknown marketing reason, Corel limited MF 7 Pro to Asia/Oceania and possibly Europe.) I also acted as one of the Beta testers of this SE release. Like its predecessors it works extremely well.
The release, unfortunately for some, is being done by the same method as the other updates for X3: via the Get More function. I have not yet been given a URL where it can be downloaded separately. In fact, I am rather doubtful that such an URL will be released since Corel obviously wish to restrict downloads to those who have a copy of X3.
I suspect a downside is that for new users of X3, it will again take 3 days for the download of MF7 SE to appear. (This strangely enough will include me as I just bought a new computer yesterday, and have installed X3 on it. But as yet -- unsurprisingly -- I don't even have the template packs showing in the Get More tab! But I guess I can install the full MF 7 Pro on this machine...)
MF7 SE has a virtually identical appearance to the full verions of MF7 and its predecessors, and a close similarity to the burning module of VS X2 and its predecessors. It will thus be very easy for users of previous versions to use.
It should be noted that the main limitation of this SE version is that it requires the user to first produce a final version of a video in X3. Then you open MF7 SE and insert that video or videos for authoring as normal. It will not accept project files from X3.
View 14 Replies
View Related
Oct 6, 2010
I've completed a project in X3 and burnt a DVD using X2 after reading some of the negative reviews of X3 authoring. I did burn a copy using MovieFactory 7 SE but found it was glitchy (stopping and jumping) which I attributed to my inability to lower the burn speed from 'Maximum'.
The on-screen quality of the MovieFactory DVD is better than the quality of the X2 authored DVD despite the fact that all settings appear to be identical! Looking at the titling, it is noticeably sharper in MovieFactory.
Settings on both are:
MPEG files
24 bits, 720 x 576, 25 fps
Frame-based
(DVD-PAL), 16:9
Video data rate: Variable (Max. 7000 kbps)
Audio data rate: 256 kbps
Dolby Digital Audio, 48 KHz, 2/0(L,R)
Also, the files on the MovieFactory DVD are slightly larger suggesting there is some extra data (quality?) on it.
View 6 Replies
View Related
Dec 31, 2010
I am using VS X2, very happy with it. I have been burning a few SD DVDs with AVCHD and very happy there, too. The authoring options and menu templates is quite limited when compared to my options when creating a standard DVD.
I need to know what is the best additional program I should use to have more options when creating AVCHD discs and Blu-Ray when that time comes. Is it movie Factory 7? IS MF 6 more compatible with VS X2 and will it give me the same features as 7?
View 5 Replies
View Related
May 25, 2012
I'm trying to create a blu-ray movie that contains AVCHD videos of various vacations that I've been on over the past year (just your typical collection of home movies), but I've had problem after problem in trying to create the damn thing. I've used VS Pro X4 to create four individual movies (representing four different vacations, each saved as vsp files); I then created my "menu file" to compile all four movies into a single blu-ray with each one having menu buttons that then go to chapter sections. Then, due to VSX4 never completing a successful burn, I simply had it create the Blu-Ray folders and then used ImgBurn to burn them to disc.
ANYWAYS, what kind of project settings do I need to be using in VS? I will be playing the disc in a PS3 (not sure if that matters as opposed to a regular BD player). I finally managed to produce a successful burn, but it was only able to play once in my PS3 - for some reason after it initially played fine, it wouldn't play again even though there was no damage to the disc. The disc was a BD-RE DL by Maxell. I had previously tried BD-DL Verbatim discs, but I was never able to finish a burn with those.
I'm just trying to figure out why I'm having so much trouble getting my movie from my computer to a playable disc!! Dx
Here are my current project settings:NTSC drop frame (29.97 fps)MPEG files24 bits, 720 x 480, 29.97 fpsUpper Field First(DVD-NTSC), 16:9Video data rate: Variable (Max. 8000 kbps) LPCM Audio, 48000 Hz, StereoAnd here is a screenshot of my Share > Create Blu-ray properties: click.
Blu-ray burner that I'm using: Matshita BD-MLT U240AF. It is connected via USB cable to my Vista 64 laptop. All of my drivers are up to date.
View 14 Replies
View Related
Sep 18, 2011
I have run into a roadblock -- I am having trouble authoring my DVD. I have watched the tutorials and read (and re-read) the User Guide.
I used my Canon HF S200 to shoot video of family reunions. It is about 2 1/2 hours long and I have about 32 chapters. I am ready to burn a DVD. but my chapters weren't appearing in the DVD Preview.
Further investigation showed that my project is 10.01 GBs and that my DVD only has 4.38 GB usable space.
It doesn't make sense to me. I rent Hollywood movies all the time that are nearly 3 hours long -- and those are certainly much more detailed than my little video.
I really don't want to split this project into 3 DVDs == that would be stupid.
How can I adjust settings so that my DVD fits -- and all of my Chapters appear in the DVD Preview prior to burning? I would like wide screen setting.
View 6 Replies
View Related
