I am having an issue with drawing files. I have set views on assembly files. But on the idw file it is showing wrong views... And this is making problems when i am trying to give dimensions. I have attached jpg files.
View 7 RepliesAn IDW view is showing a second iteration of a part instead of one of each. I have tried turning the visibly on / off in the ipn. I have also toggled the associativity on / off. The view shows the correct image during its preview, but when the view is done being created, it shows the wrong part again.
View 6 Replies View RelatedI use the split face tool on my ipt. When i create a idw of this part I want to show the split face line in the drawing. When I initially place the view the line is shown, however when the place view command is finished the line is not shown.
I see nothing obvious in the place view dialog box controlling the visibility of this line............how do i show this line in the view?
Inventor 2012, windows xp
Inventor 2010 Certified Professional
Can we show or hide the model edges with respect to Features or parts. I think, there must be only two options. ie. "Show all hidden edges" or "show all" and "Hide all edges".
View 3 Replies View RelatedC3D 2013 64 Bit, Win 7 Pro 64Bit
When I use the open command in C3D the file date is incorrect for a file. I also have a explorer windows open and it shows the same file with the current date.
This file is located on my local hard drive. C3D shows 11/15/2013 for the date the actual date of the file is 11/26/2013. Even after a save it's still wrong. My isavepercent is set to 0 .
I have two problems with a IDW drawing.
Most of my views have been crosed over by a red line in the Model browser window (se attachment) What does this red line meen?
Also, all the views with the red line have been set to Raster View Only. I can untick it without problems, but when I click OK and reopen the dialog the checkmark is back on.
How come inventor turns this mark on by itself?
Using Inventor 2014 64-bit
An IPN file is showing multiple assembly files in it's browser even though I have confirmed there is only one of the assemblies in the IAM file.
I'm not sure if it's causing any real difficulty in the IDW views but it's not giving me any confidence.
When is the poor, undercared-for part of the software going to get an overhaul?
I made a complex drawing.
Now i changed the part file just a little, the placement of a few holes, and saved it to a new name.
I need both versions.
In the Design Assistant i copied the drawing file to a new name.
Now i want, in the design assistant, to replace the file the drawing refferences, but can't, the replace option is greyed.
I understand there might be larger changes, is that the reason?
I've created a drawing and when I create a detail view, the actual view appears in the drawing but the circle and arrows along with the view identifier are not showing up. It's like the visibility has been turn off. how to turn it back on?
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
how to show section view in base view with out projection the component.
View 2 Replies View Relatedunable to select an edge in the drawing view to create a general dimension.
View 1 Replies View RelatedSee the jpeg: 1.345 is a regular dimension, .875 is a hole note. The hole note is wrong.
(the part doesn’t have to be scrapped. It can be dis assembled, sent back for rework, refinished and reassembled.)
I have created an iLogic panel which allows me to control my revision a lot easier and puts my entered data into the parameters of the sheet itself, is there a way to have this show up on the drawing itself for a template?
View 1 Replies View RelatedIs it possible to have the parent view for the section in one drawing and the child views in another drawing?
View 2 Replies View RelatedAfter upgrading to Inventor 2014 we notice that the graphics do not work properly, and that the overall performance in drawings and modelling bad compared to 2013. Then we installed SP1 and now drawing views are disappearing, however when we select "shaded" view the view reappears and works perfectly..
Any workaround regarding disappearing views?
Each time when I place a part in base view, have to follow few steps; go through view label, format Text, than choose type option - [Properties-Model] and its property - [Part Number], than placing dimensions. it takes long time and very repetitive, especially, when placing a hundreds of parts and I was wondering if there is an option, to set up view label; [Properties - Model ]& [Part number], as a DEFAULT. So, each time placing a part, in base view it will come up with correct label. Also, overall dimensions, can it be retrieve using parameters of the part?
View 4 Replies View RelatedWhen creating a new view of flighting on a tube part of it shows up like it should and part shows up as dashed lines and when you turn on "shaded" the parts that are dashed do not shade. All of the flighting parts come out of the same file and the tube is from a different file.
View 5 Replies View RelatedI have recently bought a Canon 650D and I am now unable to load CR2 Raw files in to Elements 10 for editing-it is coming up with a message "Cannot open ....... CR2 because it is the wrong type of file. I have not had this problem before.
View 12 Replies View RelatedRunning into some strange text issues... fonts having problems and text not showing on the drawing that is in the text box. (shows fine with out the bold option but does not when its turned on)
files attached should explain.
inv 2012
sp up to date
I'm trying to make a view showing a motor-jackscrew unit with the jackscrew at the fully retracted position and also with the jackscrew at the fully extended position (in phantom). Refer to the attachment.
My initial plan was to have two views in the drawing, one retracted and one extended, and then just align them vertically and horizontally. But it turns out that you can only align vertically OR horizontally, not both at the same time. So I created an assembly of two iAssemblies, one with the screw extended and one retracted. Then I made the drawing view from the direction that placed the extended assembly directly behind the retracted assembly.
I have a part in which one of the folds needs to be done at assembly and not during manufacturing of the other bends.
Is there a way I can show this so that the manufacturing print sees exactly what they need to do and nothing more but then on the unit assembly the assemblers see that the unfolded tab needs to be folded down?
Can this be done all in one part file?
I have an assembly of a rod in a cylinder. When compressed, this rod sticks out 10mm from the cylinder. When extended, this rod sticks out 50mm. I am trying to create a drawing which shows the compressed state and extended state together.
View 3 Replies View Relatedwhen putting a bmp image on the ipt and creating the decal works fine. When I bring the ipt in to the drawing it fades out from the center to the upper right hand side. How to fix it in 2012. In 2009 it was simple to fix this by changing to open gl setting in application options, hardware.
View 2 Replies View RelatedWe have our first project in Revit that we are having to split among multiple sheets because of the size of the building, so I have made 3 dependent views from the main overall view, named them, cropped them and placed each part (A,B, and C) on separate sheets. Now that I am trying to do enlarged toilet plan views, I want to tag the plans with the plan callouts on the 1/8” sheets that are the dependent views, but all the view tags are referencing dependent view A since it is the first dependent view in the list. If I change sheet A to be named Sheet X for instance, all the view tags now reference sheet B since that becomes the first dependent view alphabetically. I want them to reference the sheet they appear in, but I can’t seem to figure out how to do that, even though they are in different dependent views completely and within the crop region, they all default to the first dependent view in alphabetical order.
View 4 Replies View RelatedI have an assembly which is a plated structure. I am using a skeleton file of surfaces to define these plates. I am deriving the required surface/s from this skeleton file into a part file. In the part file I have used thicken to create my plate part. I also turn off the visibility of all derived surfaces in this part.
Now in the plate part when I go into edit derived part - the surface I have used is not grayed out showing it has been consumed by my thicken feature??? I place all my part files into an assembly and create views for each part using isolate (I use these views in a drawing which is used for NC plate cutting)
So the problem I am having is that when I place a view in my drawing the derived surfaces are also showing.
However I have used this modeling technique for many previous projects on previous versions of inventor and have never had this problem.
As mentioned above I have used isolate to create these views. I have since gone back and created the views by turning off the visibility of all other components and the surfaces do not appear in my drawing views.
Been trying to show multiple layers/coatings in my drawing for several hours now, and finally defeated,
I have a revolved part that's made of multiple layers -- aluminum, for example, with an anodized coating and then a paint on top. I need to make a detailed drawing to show how thick each layer is, and to that end, created the part profile, added an offset rotation for layer 1 and then another offset rotation for layer two. They're thus symmetric and in full contact, but separate, distinct layers. No problem.
Turning this into a precise drawing, however, is a bit harder, since all of the layers render into one monolithic revolution. I need to show those layers distinctly, like in the png file attached. Is that possible?
I need to show feet and meters in my drawing. I got them to show up, however the decimal is in the wrong spot. Instead of it being 1.8288 meters for 6 ft., it's showing as 1828.8. Everything I read says to 'just move the decimal'. But how do I do that without overriding the actual dimension?
View 4 Replies View RelatedI'm working on a Isometric drawing and im trying to dimension the view. I keep the original view there and cut another of the same view and place that cut view over the original, so I have something to snap to while dimensioning.
Every time i go to place the cut view over the original and i always grab the wrong view and move it and I am wondering if there is a way to pin the original view in place permanently?
I'm having problems with PS showing red and purple as blue. The RAW's are oversaturated with blue and nothing I do can reverse the colours. Both camera, PS and monitor is set to aRGB and the RAW files is showed correctly in the Windows folder. both the highlight and shadow warning are turned off!
View 1 Replies View RelatedI made some changes to our normal template file for inventor and saved it to my hard drive in the public folder. When i open through windows explorer its fine and everything is correct. When i open a new idw and select this file through inventor it comes in with some of the tables having different size text and none of my leaders coming in.
View 7 Replies View RelatedIs there a way so that when I make a view in a drawing,
it shows up by default with all it's real lines, instead of having to select the options all the time...