Have a site plan and about to make a revision to building layout, storm, sanitary, parking layout. Have a project folder, with Drawings subfolder, and then subfolder for Model Files and Sheet Files. How do most go about archiving the original drawings without affecting shortcuts and xrefs.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
I know storm and sewer design possible. But I cannot know if possible to design the pressure network pipe layout?
View 9 Replies View RelatedIs there a way to customize the way Design Center Imports Layout Tabs?
When you import a Layout, it brings with it all attached images from the source drawings even if they are in Model Space.
planning consultant has asked me to show the roof pitches on a site plan.
View 9 Replies View RelatedI have changed the model to show new areas and coloured them in. They show up on the Model, but not on the set up Site Layout that you print. I can highlight part for the drawing and it will print with the changes. However, if I require the whole drawing the Site Layout prints without the changes. What do I need to do?
View 6 Replies View RelatedInventor 2012, DWG drawing file Revision table - iLogic
Using iLogic, how to extract data from "Design Tracking Properties" in a revision table to an embedded or linked Excel spread sheet? Design Tracking Properties like "Today's Date", "Designer", "Checked By", "Eng Approved By" are of great interest.
I'm trying to build a site for a holiday villa and am having design block! I've tried out various headers and don't like any of them. I want to have a rounded rectangle navigation on the left side but not sure?
View 2 Replies View Relatedhow they drew they lay out for this site and where can i get some of the side way trinagles in the navigation and stars. ANy brushes any ideas?
View 7 Replies View RelatedThe website is run on WordPress, and so I did not design the site in Xara. However, I designed the graphics. I had them all in one Xara file. Today, I wanted to add more mouseovers. You can see the ones I have by hovering over the right-hand side of the page. There were 5 or so pages in the file with a variety of ideas and small graphics that I exported to png files and uploaded to the site.
When I opened the file, it had only 1 blank page. I was horrified. I noticed that the latest and greatest Xara is a bit quirky, compared to the previous 2 versions.
I am trying to import an updated phase (shown in yellow) into an existing site layout (grey) however I cannot get it to rotate round and fit correctly. I imagine it will involve using the rotate command and reference.
View 4 Replies View RelatedI've attached two screenshots of my issue. I simply need to change my major station from 1000' interval to 500' interval. As you can see from the screen caps, I can manage to get the band details on the stations I want, through a workaround, but the vertical gridlines get all messed up.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
Is it possible to change the Alignment Labels Major Stations Increment for multiple Alignments ?I have 50+ Alignments. Each of them labelled with 100m increment for major stations.I would like to change them to 50m interval.
View 2 Replies View RelatedCan I turn off the begin and end vertical grid of a profile? Currently it can be turned off using the GRID AT VERTICAL MAJOR, even though I'm starting/ending my profile view at stations that are neither major (100') nor minor (50').
Civil 3D 2010.
I attached a pdf to show the vertical line at 19+90 that I want turned off.
I'm trying to make a layout for a site that requires the height in the file name.So I was wondering if paint.net had a function similar to this picture (photoshop) or is there any other way to measure height?
[URL]......
I am trying to create some new templates for 2013 and I'm trying to figure a way to get the model revision number to populate into the drawing's iproperty revision number so that they will match upon save. I'm trying to do this by creating an ilogic rule but I don't see a system property in the idw that will allow me to access the 3D model iprops. I am going to Event Trigger the rule to run Before Save. Is this possible?
On the drawing border I have created a formatted text box that is built as:
Type: Properties - Model
Property: Revision Number
It simply pulls the data from the models revision number and populates the text box. I need this same thing to happen but rather than populate into a text box I need it to populate into the drawings revision number iprop.
Boxx Technologies 4920 Xtreme - Win7 64bit
Intel Core i7 3960X @ 4.5 GHz - 64GB RAM
NVidia Quadro 4000 - Quadro 600 - Tesla C2075 (driver 307.45)
Product Design Suite 2014 (SP1) - Vault 2014 Pro SubRel1 - CFD Sim 2014 - Bunkspeed Pro 2012
I have a bit of a problem with Autocad map 3d 2012. When i try to insert a scale bar or a north arrow or any other carthographic element i simply can't find the layout elements that are supposed to be in layout tools tab. I've done a lot of research online and can't come up with anything.
View 2 Replies View RelatedIs there any reason to have aligments in a site instead of jsut under the general alignments?
View 3 Replies View Relatedfake magazine layout design,
View 2 Replies View RelatedWhat is the Revision Number field in Surface Statistics for and how/when is it populated?
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
Is there a method to obtain the overall Site boundary? I have not found one, if there is, but it would sure come in handy when creating reports. We must always include the project Boundary as the first item in a report, so being able to add it to the existing reports would be a huge timesaver.
View 6 Replies View RelatedI would like the grading of a site to happen only on part of the site; I need the rest of the site to remain unchanged.
I thought I was finished with this project, the volumes seemed about correct, and then I noticed in the comparison surface (showing areas of Cut and areas of Fill) that soil is being taken from parts of the site that need to remain undisturbed. This is a residential site with a conservation easement and other forested areas that we won't be disturbing.
How do I set a boundary or breakline (or what?) to limit the grading/cut/fill to the area I want?
AutoCAD Civil 3D 2010
If I have a site that I want to grade using two different configurations whats the proper hierarchy of everything? I am confused as to sites-grading groups-surfaces and how they mesh.
Concept A - Site with FFE of 471
Concept B - Site with FFE of 465
I want to print off a site using a makerbot that contains some retaining walls as a present for our client. I was hoping to use 123D to print it off to a makerbot, but I have been unable to load a drawing in it. How to 3d print a site, and if so what tricks you have used. I am currently trying to make a solid from a surface and see if that will export.
View 6 Replies View RelatedI am trying to fix the grading on a flat site. As part of that I have all the islands labled A1, A2, A3, B1, B2, B3.
I would like to have the feature lines have the same prefix as the islands. I can create feature line and it will give me the option "Feature". I over write to A1, etc. The next time I add a feature line it flips back to "Feature"
How it picks the prefix for the 6" offset for top & bottom of curb. It would be nice to be able have it keep the prefix until you tell it differently without having to flip to the settings tab for each island.
2012
I have a rogue feature line that I do not know where or why it appeared from. (Somehow it is a duplicate of my curb line, but offset.)I cannot delete this feature line. It is not applied to any surface as a break line, but when I go to delete it, it freezes autocad.
I have done all the basic steps of purging, audit, recovering, even tried mapclean and I still cannot delete it.
Is there a way to control what layer a site is created on?
I am surprised I hadn't noticed until now that a site is actually an AECC_PARCEL In 2012 it comes in on the current layer. This causes some undesirable behavior. If your current layer is locked you are unable to create a site. If you later lock the layer the site is on you are prevented from changing site properties. I found it when I could not purge a layer because it contained the site.
Civil 3D 2012 SP3 | Win 7 64-bit SP1
Xeon E5-1620 @ 3.60GHz, 16GB Ram | NVidia Quadro 600
i have a preliminary alignment used to create some proposed profiles now we have pin point the location of the correct alignment and i want to copy serveal profiles from the preliminary aligment to the new alignment all at once instead of one at a time with superimpose.
View 4 Replies View RelatedI have a number of drawings that i need to change the revision numbers, insert the date, the reviewer, etc.... I have been doing this manually but it takes heaps of time. Is there an easier way to copy and paste multiline attributes from one block to the same block used in other drawings (each drawings has the same block and attribute titles). One problem is that i cant simply copy the entire block as the drawing number, reviewers, titles etc are different in each drawing.
View 1 Replies View RelatedI created a few different Sites as I created Feature lines in order to keep them separate and avoid having one affect the others. The problem is that I am now stuck in the Last Site created. So commands like "QUICKEDITFEATUREELEVS" only see those feature lines in the last Site created. How can I switch to another site so I can quickly edit those feature lines?
View 3 Replies View RelatedC3D 2012
I have a number of Sites in my drawing. I want to be able to set a Site current (in LISP) so that when you create or draw a feature line, the site is set to the desired value. I haven't seen a variable or setting for this.
I've got a series of cross sections that show an existing and proposed scenario and I need to show the location of the site boundary on the (multiple) sections.
I tried making a feature line from the site boundary but all the feature lines get projected - how can I just get the site boundary to be shown?