Is it possible to change the Alignment Labels Major Stations Increment for multiple Alignments ?I have 50+ Alignments. Each of them labelled with 100m increment for major stations.I would like to change them to 50m interval.
View 2 RepliesI need to figure out a way to sample multiple surfaces for multiple alignments.
Example 1: I am creating cross sections for a river dredge showing the pre-dredge bathymetry, design dredge elevation, and post-dredge bathymetry results. I have 100's of alignments that I need to sample 3 surfaces and display in profile view. Due to the clients requirements for display, using the cross section tools don't work for me, so I have resorted to using a seperate alignment for each cross section.
Example 2: Working in a subdivision with many utility alignments it would save quite a bit of time to be able to choose a group of alignments and sample multiple surfaces in just a few clicks.
I've attached two screenshots of my issue. I simply need to change my major station from 1000' interval to 500' interval. As you can see from the screen caps, I can manage to get the band details on the stations I want, through a workaround, but the vertical gridlines get all messed up.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
I am using Civil 3d 2012. What I have is a surface along railroad tracks. Each set of tracks has a different alignment because they aren't parallel. I have a baseline alignment with my stationing set on that. What I want to do is have one profile view showing the multiple track alignments based on the baseline alignment. I can't use the offset alignment because they aren't parallel.
View 1 Replies View Related2012 SP2
I'm having a problem with profile shortcuts showing up under multiple alignments. I have 16-alignments and profiles in their own drawings. I didn't create the shortcuts right away as I was still figuring out how I wanted the project dir structure. When I had that solved, I started creating the shortcuts. When I checked them, some of the alignments had up to 6-profiles from other alignments listed under them. One alignment had 3-profiles, and not one of them was for the alignment.
I removed all the profile shortcuts and started bringing them in again. Same problem. This was after shutting C3D down, cleaning up the tmp files and restarting.
There are shortcuts for 36 other alignments, and none of them appear to be affected, only these last 16. Validate Data Shorcuts doesn't do anything.
I am working on a water line replacement job in a residential neighborhood. Some of the streets are getting the water line replaced and some are not. I have created an alignment for the water line on the streets that are being replaced.
When I create my view frame group along each alignment, there are some overlapping view frames from different alignments. I need to create a matchline for these instances. How to create matchlines for view frames on different alignments? Or create one view frame group from different alignments?
How do i export multiple alignments from civil 3D 2013 to hecras?
View 2 Replies View RelatedI have an alignment and have station labels. The alignment is labeled with "Major Stations" at every 100 feet. I need to change the station increment to 25 feet and have labels. I have done this although station 1+25 is still reading 1, station 1+50 is reading 1, etc. There is a precision variable somewhere, and I can't figure it out. I have played with the alignment labels style but no luck. Is there a global drawing settings somewhere that might be controlling this?
View 2 Replies View RelatedWhen creating plan and profile sheets with multiple alignments in the view, what is a common practice in civil 3d?
- Data shortcut all alignments that are in the view into the plan and profile model
- Create a dwg that has all the alignments data shortcutted and xref that into the plan and profile dwg
- Create a dwg for each alignment and xref into an overall alignment dwg via attach and then xref the overall into the pp sheets dwg model.
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
Is there a way to change the settings on the Profile Layout Parameters to display as Gradients instead of the default Slopes?
E.g. I'd like to type in 1 in 150 instead of 0.6666666% etc
How can I transfer (download) measured data from total stations 'Trimble' and "Leica" to AutoCAd Civil 3D 2013? Must I find a module from the sites of these manufacturers? Or how can I change from total stations formats to the Feald Book format?
View 6 Replies View RelatedI am using the profile sample VB.net program to create an alignment, profile view and profile. The profile view defaults to start at station -0+25. I want to set the Profile View starting station based on the "Align_strt_sta" value I have defined based on the Alignment Stationing. I have tried the .StationStart() shown below, but I just get a unhandled exception.
' Create the profile view and add it to the alignment's ' collection of profile views. If oProfileView Is Nothing Then id = ProfileView.Create(m_CivilDoc, Prof_View_Name, PROFILEVIEW_BANDSET_STYLE_NAME, Align_Name, pviewposition) oProfileView = pviewTransaction.GetObject(id, OpenMode.ForWrite) End If 'oProfileView.StationStart() = Align_Strt_Sta oProfileView.Description = "Profile view of alignment '" & m_SampleAlignment.Name & "'" oProfileView.StyleName = PROFILE_VIEW_STYLE_NAME
Have a site plan and about to make a revision to building layout, storm, sanitary, parking layout. Have a project folder, with Drawings subfolder, and then subfolder for Model Files and Sheet Files. How do most go about archiving the original drawings without affecting shortcuts and xrefs.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
Creating points at the stations of an alignment,
I wanted to get the (x,y,z) of the stations of an alignment, but sounds not to work.
In the screenshots below, I got the message “The specified station is not valid for this object” and couldn’t proceed!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I was trying to find a way to not have the last ending Station Label show up on my centerline is there a override or way to tell it to just label to the last 100 or 50 foot station?
View 4 Replies View RelatedIs there a way to model an intelligent petrol interceptor and pumping station in Civils 3D?
If so will these integrate with Windes?
How do I get Civil 3D to put pipe elevation labels at even stations?
View 1 Replies View RelatedI have created a slope stake report and have just noticed that there are stations missing. The stations are there in the cross secitons but not there in the slope stake report.
All sample lines were created at the same time. All surfaces are present throughout the entire cooridor.
How to calculate in a table the volume of cut and fill between the stations, The horizontal and vertical alignments are generated along with their sections. I’m wondering if there is a tool that summarize the volume of cut and fill between the stations in a table.
View 3 Replies View Related(Again): Plotting points at stations of horizontal alignment,
I wanted to plot points at the stations of horizontal alignment to be then able to capture their XYZ and thus can be stored on the GPS devise for setting out on the field.
The points are not plotted (see the attached screenshots
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Land desktop anchored the alignment stationing at the "+" sign directly on the alignment.
Is there a way to do the same in C3D 2010 without adjusting the x,y locations?
I have daylight_cut at say station 100, then sampled every 20m, however it connect from station 100 all the way to 1000 for example. because there is no such code in between. why can't it create seperate features lines? the thing is sometimes it does it and sometimes it doesn't.
see the redline cutting across the corridor? shouldn't be there.
I have an alignment and would only like to label stations and specific geometry points such as EC/BC. When I add geometry points to my label set it automatically gives me curve midpoints and beg/end of alignment. How can I turn off these labels so that I only get BC/EC?
View 1 Replies View RelatedI am having an issue with my section views. Some of my subassemblies are only showing on certain stations. If I view the stations on the cross section editor, the corridor looks just fine, but when I go to the section sheet where the corridor is x-referenced, the driveway disappears.
I have rebuilt the corridor numerous times, detached and reattached the drawing, made a new drawing and recreated the sample lines to no avail. Attached are some pictures to show the disappearing driveway on the right side of the street.
When I change to process 2012 on an image that has been worked in 2010 I'm seeing a big change in the image, much brighter, less contrast. Any way to closely preserve the old look while updating the process?
Also wondering what the new 2012 process brings to the image, aside from access to the new tools. Will I see a better (or just different) rendering of the image from older files?
Can I turn off the begin and end vertical grid of a profile? Currently it can be turned off using the GRID AT VERTICAL MAJOR, even though I'm starting/ending my profile view at stations that are neither major (100') nor minor (50').
Civil 3D 2010.
I attached a pdf to show the vertical line at 19+90 that I want turned off.
What could be the trick with corridor section editor in C3D 2014, applying overrides to a stations range won't work. After selecting or typing end station in the 'apply to a station range' prompt nothing happens, the overrides just will not be applied.
To apply overrides for an subassembly (curb depth etc) I must go through all the stations set by corridor frequency in the station range. This is not file specific, as it is the case with all my projects.
I create the sampleline on the option "by a range of stations" so the sample lines were created on the horizontal geometry points. When I change the geometry of the alignament, the sample lines's local change or I need to do the process all over again?
View 1 Replies View RelatedI have an alignment that starts at station 1+00 and runs through 20+00.
By right clicking the station labels and editing the label group, I have updated my major station increments to 200' and my minor stations (ticks only) to 100'. The problem is, I want the 200' increments to begin at my starting station (1+00), so that the labels would read 1+00, 3+00, 5+00, etc.
As it is now, the above settings make my labels read: 1+00, 2+00, 4+00, 6+00, etc.
Is it possible to insert a "field" instruction in the drawing template to get automatically the stations (beginning and end) of the long profile for the sheet considered ?
Example 0+700 - 1+400
This is using Civil 3D 2012 Service Pack 2.1
When a Station Equation is added to an alignment it causes all of the profile views to get messed up. In addition once the EG profile changes the entire FG profile may also need to be changed. See this video I uploaded to Youtube that fully explains and shows the problem: [URL] ........
So, any way to some how lock the profile views start and end stations? Or to some how lock the PVI locations on a a proposed profile to certain stations?