Is there a method to obtain the overall Site boundary? I have not found one, if there is, but it would sure come in handy when creating reports. We must always include the project Boundary as the first item in a report, so being able to add it to the existing reports would be a huge timesaver.
View 6 RepliesI've got a series of cross sections that show an existing and proposed scenario and I need to show the location of the site boundary on the (multiple) sections.
I tried making a feature line from the site boundary but all the feature lines get projected - how can I just get the site boundary to be shown?
i need to know if there is any way to control the points in the point cloud.
1. either only import the point cloud in a polyline area i specify
2. add all the points within a boundary not limited to the pointclouddensity = 100, freaking default is 15 almost cost my job today. extremely stressed out right now.
i am talking about extreme lidar surveys. 1km 1km LAS/0.5m contours/xyz files times 355 of them. covers a 2km wide corridor. but i only need 100m wide after i define the road alignment. no need to have all the extra points.
right now i densify the heck out of it and end up like 5-12m points. decent but not good enough because the geotech is bitching about that accuracy is not good for some feasibility study. or is there any software i can do this besides civil 3d.
what i want can also do is automate the 'add points to surface" under point cloud and have the software do multiple boundaries without having me baby it over the night. right now every click is 5 minutes and adds like 400k to 1 million points. Civil 3D 2012
I used a 2d polyline to create a surface boundary for a surface created. The polyline is a closed loop. For the boundary type it is outer, unchecked Non-destructive breakline, and mid-ordinate distance = 1.
My problem is that when I do this I only get a small portion of the surface to show up within my surface boundary. If I don't have a surface boundary the entire drawing surface shows up no problem.
The purple polyline is my boundary and the light blue is the surface created within the boundary.
Is there any reason to have aligments in a site instead of jsut under the general alignments?
View 3 Replies View RelatedI would like the grading of a site to happen only on part of the site; I need the rest of the site to remain unchanged.
I thought I was finished with this project, the volumes seemed about correct, and then I noticed in the comparison surface (showing areas of Cut and areas of Fill) that soil is being taken from parts of the site that need to remain undisturbed. This is a residential site with a conservation easement and other forested areas that we won't be disturbing.
How do I set a boundary or breakline (or what?) to limit the grading/cut/fill to the area I want?
AutoCAD Civil 3D 2010
If I have a site that I want to grade using two different configurations whats the proper hierarchy of everything? I am confused as to sites-grading groups-surfaces and how they mesh.
Concept A - Site with FFE of 471
Concept B - Site with FFE of 465
I want to print off a site using a makerbot that contains some retaining walls as a present for our client. I was hoping to use 123D to print it off to a makerbot, but I have been unable to load a drawing in it. How to 3d print a site, and if so what tricks you have used. I am currently trying to make a solid from a surface and see if that will export.
View 6 Replies View RelatedI am trying to fix the grading on a flat site. As part of that I have all the islands labled A1, A2, A3, B1, B2, B3.
I would like to have the feature lines have the same prefix as the islands. I can create feature line and it will give me the option "Feature". I over write to A1, etc. The next time I add a feature line it flips back to "Feature"
How it picks the prefix for the 6" offset for top & bottom of curb. It would be nice to be able have it keep the prefix until you tell it differently without having to flip to the settings tab for each island.
2012
I have a rogue feature line that I do not know where or why it appeared from. (Somehow it is a duplicate of my curb line, but offset.)I cannot delete this feature line. It is not applied to any surface as a break line, but when I go to delete it, it freezes autocad.
I have done all the basic steps of purging, audit, recovering, even tried mapclean and I still cannot delete it.
Is there a way to control what layer a site is created on?
I am surprised I hadn't noticed until now that a site is actually an AECC_PARCEL In 2012 it comes in on the current layer. This causes some undesirable behavior. If your current layer is locked you are unable to create a site. If you later lock the layer the site is on you are prevented from changing site properties. I found it when I could not purge a layer because it contained the site.
Civil 3D 2012 SP3 | Win 7 64-bit SP1
Xeon E5-1620 @ 3.60GHz, 16GB Ram | NVidia Quadro 600
i have a preliminary alignment used to create some proposed profiles now we have pin point the location of the correct alignment and i want to copy serveal profiles from the preliminary aligment to the new alignment all at once instead of one at a time with superimpose.
View 4 Replies View RelatedHave a site plan and about to make a revision to building layout, storm, sanitary, parking layout. Have a project folder, with Drawings subfolder, and then subfolder for Model Files and Sheet Files. How do most go about archiving the original drawings without affecting shortcuts and xrefs.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
I created a few different Sites as I created Feature lines in order to keep them separate and avoid having one affect the others. The problem is that I am now stuck in the Last Site created. So commands like "QUICKEDITFEATUREELEVS" only see those feature lines in the last Site created. How can I switch to another site so I can quickly edit those feature lines?
View 3 Replies View RelatedI have survey data of the inside floor of a pond ( the pond has a flat floor ). The surface made from the survey data needs to extend to the outline of the pond instead of the outline of the survey points.
I tried the smooth surface method of kriging with a grid base and I sellected the outline of the pond for the output region and that worked somewhat but there are still gaps between the boarder and the surface.
I have alignments that go in and out of a surface boundary (this is because I have a surface that represents the bottom of pavement.) I want to show the surface profile with the gaps in the profile view (where there is no surface. However in the profile view the gaps are sometimes connected with a straight line instead of being blank.
How can I have a surface profile represent the bottom of pavement properly? (An alignment that is not fully withing the surface boundary.) I know I could add the profile multiple time with different start/end stations But, I don't want that, I want it to be dynamic, as the alignment will change.
I would like to show the title boundary of our site on a profile in a way that is dynamic. Same idea than on cross sections, where you can create an alignment running along the title boundary and then show a block where the boundary lies on each cross section. I know I could project a cogo point where the alignment intersects the boundary.
This method is not perfect because, if the alignment changes and, therefore, the intersection point with the boundary changes too, the cogo point won't follow the alignment, staying at its original location. Hence, I'll have to update it manually. I tried using a feature line, but it seems I cannot show a marker only where it intersects the alignment.
The odd shapes are outside the daylight line. They follow a straight-line around the daylight limits (see third attached file), apparently triangulating unwanted areas. I've used a corridor shrink wrap for the surface boundary.
What is the best bet? I'd rather not draw a polygon along the daylight line and use it as a surface boundary, since it could change. Setting a max triangle length in the surface does not seem to provide a desired result.
I've attached a screenshot of the issue I'm dealing with. I have a closed polyline and when I first hatch the area it appears to be correct, but then I'll go do another command and then the hatch seems to extend beyond the boundaries of the polyline.
View 3 Replies View RelatedI have problems applying an Outer boundary to eliminate a small area within a big surface (and a few Hide boundaries within that Outer boundary): Civil 3D somehow creates extra triangles within my surface (that don't really make sense to me). I am applying the boundaries as non-destructive boundaries as I need the surface to extend all the way to my applied boundaries. The surface needs to be untouched (except applying a few Outer and Hide boundaries) as it is design data.
View 4 Replies View RelatedWhen I create a corridor surface I usually create a suface boundary automatically by daylight.Half the time this works fine, half the time it doesn't work at all. If I view the corridor in 3d view it looks fine.
I tried to create a shrinkwrap polyline to use as a boundary but when I picked the corridor in the shrinkwrap command
it locked up my computer. These are just simple corridors with no intersections. Why the automatic boundary only works intermitently? Is there a better/easier way to create the surface boundary?
I need to adjust a surface boundary. I need to remove a corrupted area in my surface. I do not need it. Is there any way to drag a boundary so I can exclude some of my contour area? Is there a command under settings on tool space that I may have overlooked? This surface was furnished by a client so I do not want to rebuild or alter except to exclude some contours.
View 1 Replies View RelatedC3D 2012
I have a number of Sites in my drawing. I want to be able to set a Site current (in LISP) so that when you create or draw a feature line, the site is set to the desired value. I haven't seen a variable or setting for this.
how to use Civil 3D to create a grading plan for a solar PV site or a golf course?
Here is the situation. We have a large 100 acre site that is not flat. We want to do minimal grading to "smooth out the surface". So that maximum slope on the site is 10%. The site does not have to be graded completely flat. We are trying to work with the existing contours and terrain as much as possible.
Is there some functiion or some way for Civil 3D to "smooth out a surface"? We want to work with the existing slopes and contours of the site and just need a grading plan that will smooth out mounds, holes, or high slope areas.
When a file has many surfaces, gradings and sites manually delete them is slow ¿is there a method to select multiple sites, surfaces and gradings on prospector and delete them all at once and not one by one?
View 1 Replies View RelatedI'm using C3D 2013. I received a survey drawing (unknown version) from a third party. I tried both xref'ing and inserting as block into my drawing and it was over 7,100' SW from my site. BUT when I copy from 0,0,0 in his drawing and paste 0,0,0 in my drawing, it lands on my site. If I xref my drawing into his drawing, it lands on his survey information. Why doesn't his drawing land on my site when I xref or insert as block?
View 6 Replies View Relatedwhat is the trick for holding triangulation within a surface boundary? I recall a setting somewhere but can't seem to find it... attached graphic, would like to hold the surface triangulation within the arcs which are in the surface definition as boundary
View 5 Replies View RelatedI like the 'Extract" feature for surfaces, where I get get the contours or boundary of a surface in PL form without having to explode the surface. I have not figured out how I can do that same thing for grading objects. So far I have been exploding grading objects and then remaking them. Seems cumbersome.
View 7 Replies View RelatedI need to convert my surface boundary to a polyline so I can use it to clip another surface. Is there a simpler way than tracing it with the polyline command?
View 3 Replies View RelatedI have a surface that I created by joining to surfaces, and now I want to reduce my boundary, how can I edit it?
windows 7, intel I7, 8 MB RAM, civil3d 2013.
I've set the corridor's surfaces to use the corridor boundariy & the datum's overhang correction to top links & bottom links, but for some reason it doesn't respect the corridor's boundary.
View 2 Replies View Related