I'm doing a road project. i've got profile grades of existing left and right ditches. in some sections we're redoing the ditches so i've got proposed left and right ditch profiles. what i want to show is where i've got proposed ditch grades, i don't want to show existing ditch grades.
The new ditches happen intermittently on the road so i would need to be able to turn off the existing ditches at various places. is this possible without exploding my existing ditch grades?
The intersection wizard makes dynamic EOP profiles based off of the cross slope from the centerline. Well the intersection tool doesn't always work with funky intersection layouts. Is it possible to manually create a dynamic EOP profile based on the cross slope from the centerline profile?
I seem to be having trouble changing the lineweight of my profile line. I have changed the line weight in the layer properties, in the Profile properties and tried changed the line weight in the pen style. Everywhere I could think I try to make the line thicker but when I plot, the line is still the same and difficult to distinguish from the grid blocks of the profile view.
I have a profile view with the existing ground profile shown. The alignment the profile is referencing was stretched at the front and now the profile markers do not line up with the profile line. The profile line updated as it should have, but the markers did not.
is there a way to draw a line in the profile view and create that line into a feature line? and if there is can i project that line into the plan? i know that you can make a feature line in the plan and project that feature line into a profile view, just wondering if you could basicly do the reverse. i don't want to make a coridor.
we use three line road profiles. If there is a bus pullout or lane transition we show the curb profile based on centerline stationing. I'm able to generate a the corridor using a transition lane assembly from centerline and targeting a widened offset alignment or just a feature line. I can import the corridor curb feature line into a profile which would be a perfect solution, but it is all truncated. (i.e. no vertical curves) I can create a profile of the offset alignment, but the stationing doesn't match centerline.
How can I either generate a non trunidicated profile from the corridor for my curb profiles? How can create a design profile of a transition/pullout curb line that I can target and plot against centerline stationing?
I want to create a profile layout by feature line. Is it possible?I have a pipe about 3 miles long, an alignment along the pipe, and a provie view showing the exisitng surface and pipe network. The pipe network was created from a feature line. I projected the feature line to the profile.
This is why I want to do this: I need to label the horizontal and vertical angle points of the pipe in plan view. I crated a style that shows the station and elevation. I want the elevation to reference the profile. But it only gives me the elevation of the surface and I need the top of pipe elevation.
I tried crate profile by layout and traced over the top of the pipe in profile but its 3 miles and it will take a long time. How to get what I want done faster?
I have a special ditch profile that I'd like to use a linetype with arrows on. Currently, it shows the arrows going up station with my mainline profile. i.e. now water does flow uphill...
I have a regular AutoCAD line in a profile view and wondered if there is a way of labeling the grade of the line. I'd think I could use and expression to calculate it. But I don't know how to automatically adjust for the vertical exaggeration without having to have a separate expression for all possible situations.
I have cut a ground line in profile view. Is there a way to "mask out" a portion of the ground line in the profile? I need to detail some stair but the surveyors only shot the top and bottom tread. I don't want to add points to the surface, I just want to draw the steps in and place them in the correct profile location. And I don't want two horizontal alignments.
When I try to create a feature line using an alignment/ profile, sometimes it gives me a feature line for the entire alignment, even though my profile is only a small segment. I made sure I selected the correct profile, and I even deleted all other surface profiles just in case. But it still gives me a wonky feature line for the entire alignment.
However, in the same file, other profiles have worked perfectly.
I created a 2d drawing of a river I am building and constructed a centerline. I already have a surface of the existing ground created from which i created an alignment of the centerline and created a profile showing the existing grade along the centerline. Then I created another alignment on the same profile which shows the bottom of my river that I want. I now want to calculate the cut and fill of my project but don't know how. Is there a way I can create a surface of my river from my profile? Or what process do I follow to apply my centerline profile to my 2d river.
I remember seeing an article or web cast on how to create a style to display a single line for a manhole. It may have been about using the parts create tool. But for the life of me, I can’t remember where I saw it.
Also I had created a style in C3D2007 to display the pipes in profile as a single line. This was done by drawing the flow arrow in a non printable colour over the top of the pipe.In C3D2008 this is no longer possible. So now what?
We are using Civil 3D 2010, Version 4.1 and it is being used on both WinXP and Win7.
This is an issue that has been coming up at different times with profile views and them shifting when viewed from our viewports in our layout tab. It looks correct in the model space. But it shifts to the right 10' in the layout tab. We have 7 tabs in this drawing. I have looked through all of the profile view settings and it does not seem like any of these are the issue. I created a new viewport in the same tab and received the same shift to the right. I then created a new tab in the same drawing (not copied from the one that has the issue), created a new viewport, and the shift is not there. The PSLTSCALE, MSLTSCALE, and LTSCALE are all set to 1 in all of th tabs.
Woudl there be a layout tab setting that is causing this? This is happening on all of our machines with this drawing so I know it is not a specific user/machine issue. I have attached a .pdf showing the three cases described above if that were to provide any additional insight.
I am wondering why the maximum hydraulic gradline in my profile plot is not matching the maximum hydraulic grade levels reported in the report or excel spread sheets.
Is there a way to project just one feature line (or anything appropiate...polyline, 3d poly etc) into the sections group or profiles ?
The thing is that Projection tool, labels everything that's a Block, Point, 3d poly ...etc to the sections group.
And it puts all labels in the same layer.
My project theme requires to project forest limit on every section. This is appearing on the survey as a polyline along the road. Civil Engineer / Infrastructure of metropolitan transports [URL]
I have a finished grade surface and I have a feature line that is my waterline. I created an alignment and then recreated my feature line so they would be linked. I can then create a profile using my alignment and that shows my surface at that alignment. I can even add the waterline by using project objects to profile view.
I need to be able to edit the feature line elevations in the profile view by creating and erasing PVIs so this will tie back to my geometry.
We have a big piping job coming up and as Civil3d still lacks some of the labelling abilities we want in the profile view bands. I am updating some old vba that adds a profile line of the invert of a pipe network to a profile view effectively tracing along the bottom of the network like I know a lot of people do by hand.
My original code works on assuming that the start and end structure are at the start and end of the alignment in the revised code I want to allow for situations where this is not the case.
Leading to my question is there and easy way to find the distance a profile view part is drawn along the parent alignment or do I have look at writing my own function possibly extracting a polyline from the alignment and finding the distance using intersectionwith and distancefrom functions with the structure.
I made an alignment of road, inserted with sample line, then i made a profile. But on the sample line on profile, there is not a data of height and lenght of profile. How to get those data in road profile. I can manually draw that, but i think there is an easier way?
I created a road centerline profile and corridor and then created a profile of the two curb lines from the corridor. The road profile that I made has a vertical curve in it but the curb profiles do not show that information, just grade breaks every 25 feet based on the corridor sampling distance.
I would like to have the vertical curve information on the curb profiles.
C3D 2013. We have profile line labels, some of which get manually edited (for example, change the "<[Tangent grade(FP|P2|RN|AP|GC|UN|SD|OF)]>" to a static number such as 0.29%).
However, if you CTRL+Click and select one of these labels and change the style of that one label, then the manual edits are lost and the label reverts back to the default string.
I am working on a cylindrical part, and I need to CAD an internal feature for the part. I set up a parallel plane at the point within the geometry that the feature is to be located, and am attempting to sketch the profile of the part using the 2D sketch feature. However, the lines that I am sketching are not visible through the rest of the existing cylinder, for example, if I have draw a 30 mm line from the centre point of a 20mm radius cylinder, only the final 10 mm of the line will be shown. While the line is still functional, it is highly inconvenient when trying to sketch these features, they are difficult to work with as I can not see them through the part. Is there any way to set the defaut visibility for 2D sketches to be so that they are visible through solid parts?
I have an alignment label that I normally use to show the PVI's of a profile in the plan view.
This is a little unusual, but in a specific case I wanted to design my profile at one alignment, but show it at another. I designed my swale profile in the pathway profile view and then superimposed the swale profile on the swale profile view. I then went back to the swale alignment to add these labels.
It's a no-go AFAICT. The only profile available for me to select for these labels is the original ground profile from the surface.
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
Im creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
Ive tried to write my own code using the profile 2 as an example but it doesnt seem to work as a 3rd surface/profile and only seems to mimic the profile 2 elevation when placed in the band
My questions are as follows
1) does Civil 3d only allow 2 surface elevations in any band set? if it does allow more profiles/surface elevations what am i missing to create it?
2) if Civil 3d does alow for multiple surfaces to be shown in the band set how do i get the text component editor to supply the extra profile elevation codes? or would i need to create from scratch
3) if i need to write the code from scratch does any listing of the codes and meanings of each code ie what does RN, Uft, Sn and so forth do and mean .
I have a group of profiles in a drawing and I want to change how one of the profiles is displayed through the profile view style manager, but I do not want to change how all of the profiles look. Is there a way to change the way a single profile looks without changing all of them?
