I have a Multileader Style and have the Mtext to come in with "Underline top line". The text sits right where I want such as EXIST. 24 RCP but when I enter something with an inch or foot symbol such as EXIST. 24" RCP the text will end up sitting right on the leader line. I don't see where I can set an offset for the Mtext coming in with the leader. What can I do to make this change?
View 4 RepliesUsing Autocad 2014 and would like away to put a vertical line at the text where the leader meets it. Is this a setting that I'm missing or might there be a Lisp routine to get it? See the attached jpeg.
View 6 Replies View RelatedI am using autocad lt 2010..I am labeling items in my drawings and the text looks different in some of the leaders. When i check the properties both leaders have all the same properties that i feel are relevant.
View 9 Replies View RelatedWe are trying to use the "Underline top line" option located in the Content tab of the Modify MultiLeader Style dialog in AutoCAD 2012 (See attachment).
The minor issue we have is that there seems to be no way to adjust the gap between the text and the "underline". In regular dimensions, there is a dimvar called DIMGAP that controls this distance. Is there any way to control the distance between the top line MText and the "underline"?
I would like to try and set up a Multileader that reads the description of a block.
For example when I am making the block I would like to put some descriptive text that may say "Post top insert connected to haboe pin"
After the block is compelted and placed into a new drawing I would then select the multi leader option and then it would automtically fill in the text. (from the pre-defined description)
I would like it to be similar to a callout in solidworks.
I was under the impression that you could search mult ileader text with quick select, but 'contents' or some variant does not seem to be an option.
Tell me the easiest way to find a multileader with specific text (including the wildcard)? I expect it can be done with quick select or filter but can't get it happening.
I have multiple closed areas that i want to show the sq ft. Now i use the command multileader then click to insert a feild.
Select object then area. Now i have a leader with text. Can i extract the text to a table or spreadsheet. Or approach this differently. I use autocad lt 12
I am trying to circle one of the letters and each will receive a number sequence afterwards for the comm addresses (is what I want to do anyway). This is a gov project so I have to ensure everything is addressed properly.
Circling the prefix would make this look ideal but I don't know if there's a way to do it. I tried looking but couldn't find a way to do it.
The only way I could think to do it is do it manually with attdef and create a defined block with the prefix area already circled.
I'm fairly new to AutoCAD, and most certainly to the forum [URL]......
I have a question in regards to using Multileader text. Tolerance.jpg
The guy who used to work here made this text with a tolerance to a radius measurement. The tolerance is smaller ( no problem with that), but also adjusted to the top of the line.
I have a dwg template that has a Multileader Style that uses Annotative text. When I changed a viewport to a different scale....from 1"=1' to 3/4" =1', the text is not appearing to scale. It's very large. The Mtext changed to the correct scale but not the Multileader text. Where do I need to make a change?
View 5 Replies View RelatedI'm snapping to the corners of my multileader text boxes. OSNAPNODELEGACY is set to 1 and I'm not snapping to regular text or mtext. How can I change this behavior for the multileader text?
View 6 Replies View RelatedI'm looking for a way to convert leader and text that is separate into a multileader where the text is attached to the leader. We just updated to new standards using the multileader and all the old stuff is not attached.
I'm using AutoCad 2009.
When I try to create a multileader the text size is throwing me off. I draw the arrowhead location and landing with no problem, then the text box pops up. As I am typing the text into the textbox it shows up on the screen as if it was a text height of about 5, however it is actually 0.18. As soon as I click off the text box to complete the multileader the text shrinks down to the actual size of 0.18.
I want the height to be 5 but when I change it to 5 the text box shows up as huge, like it is about 200 or something even though it is actual 5. The textbox takes up most of the screen, as soon as I click of the text box to complete the multileader it shows up as a normal height of 5 and looks correct. This is so annoying. Multileader is the only tool that does this. A simple multiline text box works fine; as I am entering the text it is the same size the entire time, visually and actually.
At a multileader when "automatically include landing" is set to "NO" or unchecked, then a small point (like that at the end of a dimension line) is inserted in the callout block, such as the circle, which then prints. This makes for less than clean drafting to say the least--is this normal? If so, (why?!), is there any way to NOT have those points print/show up?
View 7 Replies View RelatedIs this a desired behavior on a multileader? URL....
Seems to do it for anything that is not left aligned. I think it was present in 2013 as well. I use multileaders for annotations a lot since it is easier to use them with the background masks and borders than mtexts.
I have noticed on several drawings that the multileaders change themselves when the drawing is closed and opened again. I put the multileaders in, they look fine, and when I close and open the drawing the multileader has extended itself across my text. If I edit it it fixes itself but it 'breaks' itself again once I close and open.
View 2 Replies View RelatedI am just wondering how is possible to set up a Multileader style that creates text with a background mask.
I have been trying to get this feature in the Multileader style manager and I could not find it in order to avoid to set up background mask every time I create a Multileader
I use LT 2010 and have defined a multileader style which is annontative. When i use this each time i have to make he text annotative and set the height even though it uses the right annotative text style.
View 2 Replies View RelatedI don't normally deal with multileaders with text although a drawing I have has been done with these.
The leader is justified to the left of the text. If I drag the position of the leader head to the right hand side of the text, the leader still starts from the left hand side of the text (goes at the bottom of the text) so how would I justify the leader position of a multileader to the right hand side of the text?
I had a quick look in the properties pane earlier although am fairly busy and it is only a trivial issue.
Actually We are trying AutoCAD 2010 and i have a question about multileader i cannot find in the manual.we are used to set a bright background mask under our text (including Mtext, Qleader, Dimensions) this way the printed text can be seen much better in dark area.
Now i'm am upgrading from AutoCAD 2007 and discovering Multileader (and i cannot find the Qleader button on the ribbon) so i conclude the new "standard is multileader", this is annoying because i cannot find anywhere how to put text mask background inside text in mleader. any option available? i would like to begin to use this function, but the text background is mandatory here.
My company has a template setup with an elevation callout for curb and gutter. The callout displays a box around two elevations (TC and G). The TC and G Labels after the elevations only show up in paper space on a 1"=1' scale, which is how the referenced block was set up. I need the labels to show up in 1:20 and/or 1:40 scale in paper space but only the elevations appear. I edited and saved the referenced block but the changes don't appear to have taken to the template.
View 1 Replies View RelatedI have recently converted mtext to multileader text & i thought it was causing some issues but now im not so sure. Some of my users are experiencing a long time to regen & it has caused some peoples computers to freeze up. Is there a setting or a variable that could be causing this? I am not sure if this is an issue with the multileaders or with autocad release 13 or 14 in general. I had the users turn regenauto off until i can find a solution.
View 3 Replies View RelatedI'm having a frequent but random problem with Multileaders where the landing distance will change on its own from its initial standard 1/8 inch to some relatively large negative distance which also causes the landing to disappear altogether. If I use the move trick for resetting all elevations to zero (Move 0,0,10e99 then 0,0,10e-99) the landing will reappear connecting the landing grip at the strange negative offset.
The problem seems only to happen when the leader is connected to the bottom right of the note.
When I remove the leader and add a new leader it appears correct but as soon as I save the drawing the affected Multileaders will again present this problem.
Windows 7 Professional 64-bit - Service Pack 1
Intel﴾R﴿ Core﴾TM﴿ i7-3820 CPU 3.60GHz; 16 GB DDR3 Dual Channel RAM
nVidia Quadro 4000; AutoCAD Civil 3D 2013, sp1
How can I revised the line type so that the text reads in the same direction. The linetype text auto adjust to read correctly in Model Space. However In the plan and profile drawing the site is rotated 90 degrees so when the text changes direction from northwest to northeast and the line text changes direction. I need for the text to be in the same direction the entire length of the line.
View 1 Replies View RelatedI would like to use the entmod method to rotate the text in a Multileader object. Reading the DXF code tells me the dotted pair of 42 seems to be the rotation angle, but entmoding that does nothing. Obviously I don't know how to modify this complex object.
View 3 Replies View RelatedI'm looking for a lisp routine that can find and replace multileader text.
I want to replace "T." with "T+" and "B." with "B+".
All the multileaders are on layers with a suffix of "-elev".
I'm setting up styles and trying to play spot-the-difference; I can't see any difference between these three settings.
View 9 Replies View RelatedWhat to put in the override box to start a second line of text? its autocad 2013
View 2 Replies View RelatedI am using Civil 3D 2011 because of a contract. Monday I created the View Frames and cut the sheets. As of this morning everything was printing properly. Over the day I added alignment labels to the sheets and other call outs, and now the Match Line text is not printing.
I have moved the match line object to the top of the drawing order, double checked the layer to verify that it is not set to no plot, and verified that the xref with the match line is on the top of the drawing order.
Attached is a screen capture of the corner PDF I plotted.
I have some sample lines that highlight utilities needing a section view. I've now moved my sample line to highlight the true cross section stationing for these crossings. Why doesn't the station value update for the sample line once this is moved. For some reason I remember the station text on the sample line updating itself automatically in the past.
View 2 Replies View RelatedHow to put a (Return) or Break to another text line in a label? Usually it is one big long label on one line.
View 4 Replies View Related