AutoCAD Civil 3D :: Getting 2013 Linetype Set Into 2012?
Jun 18, 2013
2013 has a linetype called "proposed tile" and another one called "existing tile." 2012 doesn't have either. Is there any way I can could get those two files so I could load those two linetypes into 2012?
We previously switched from 2010 to 2012, i transferred our pipe catalog with custom pipes. I though i did it right, but when i started editing pipes that were started in 2010 the pipe sizes were automatically changing to the wrong size after edit.
We are about to upgrade from c3d 2012 to 2013, i don't want this to happen again. proper way to transfer our customized pipe catalog?
how to get the little green rotate circle back in C3D 2012 and 2013?
When you click on a point in 2011 (at least my setup), there is a little green circle that pops up that I can click on and rotate the point around. In 2012, I have to click on the point, then right click on it, then select rotate label, only then can I rotate the thing.
Any new methods for depicting flared end sections in profile views in Civil 3D 2013 or 2012? I just loaded Civil 3D 2013 last week and have been checking to see if flared end section depiction in profile views is any better than previous versions. I haven't noticed anything different. I'm I the only one wanting a easier way to depict flared end sections in profiles? In short, I have never been able to figure it out.
I am autocad 2010 user. I have drawing files from consultants with custom linetypes. I have deleted the. shx file but need to change line type. How do I select the relevant lines to convert to normal line type?
I am currently running AutoCAD 2013 LT on a Windows 7 64 bit system. I was recently running this same software on a 32 bit system computer and everything was running properly. After the upgrade, I have noticed a linetype issue that I cannot seem to get a handle on.
We use a "insul" linetype on building sections that should come out looking like an architectural insulation pattern. After upgrading to the new computer, this linetype only reads as dots, nothing else. I have gone to other comnputers in the office that are displaying this linetype properly and have copied their acadlt.lin as well as acadltiso.lin files over to my computer and it has not solved the problem.
Is there a way to start a custom line type so that is starts and ends with "O". Right now, the default "FENCELINE1" has circles in it, but it starts and ends with a line.
Here's their code for the line:
*FENCELINE1,Fenceline circle ----0-----0----0-----0----0-----0-- A,.25,-.1,[CIRC1,ltypeshp.shx,x=-.1,s=.1],-.1,1
I already tried just putting the O's at the ends, and that didn't do it.
Below is a picture of what I'm looking to get. The top one is the FENCELINE1, the bottom one is just circles and lines, but that's how I want the linetype to look when they place it... so first click would have a circle, second click would have a circle, and the circles "in" the line would spread out evenly.
Just so you know... this is for guardrail inside a where house where it has the circle pillars on each end with circular pillars in the middle (every 8', but the spacing isn't crucial).
I have a very particular client insisting I recreate a specific lineteype. The previous technician used AutoCAD Architecture 2012 to create a shape within the linetype. I have recreated the shape, with my AutoCAD 2014, but am struggling with creating the linetype 100%, and getting into other files.
I have a layer named XYZ, that contains ARC, LINE and POLYLINE. I want to get a list of all linetypes from every ARC, LINE and PLINE. If I open the properties, if I select only the ARC, under linetype I'm getting *Varies*. Instead of*varies*, I would like to have a list of all linetypes (ARC, LINE and PLINE).
Is it possible? WOuld it also be possible to do the same for linescale or weight?
Having an issue with linetypes that are proprogating within all our drawings in our office... I have tried to purge, delete all and wblock and nothing seems to work. The only thing that I found to work is superpurge...
Junk is the drawing that I erased everything. (junk drawing is 2.6M with nothing in it...) click on this link to download... [URL]........
I wblocked out wblock drawing and the size fell but the file still has all the linetype...
If I draw something in wblock and copy clip it to another drawing then I get all the extra linetype from wblock dwg...
I have a problem between my template in inch and the one in mm.
Its the linetype scale that is wrong in the mm one, when i draw in the inch one, everything is fine but when i draw in the mm one, i have to set the ltscale to like 25 to see them at the same scale that they are in the inch one.
My guest is its because i've create my template for the mm one base on the inch one and i just change the unit type to mm. Is there a setting i could change that will arrange this?
All block containing Circle, Spline or Ellipse have Linetype Reset when they are scaled in a drawing who contain more that 1 ViewPort. (tested with CAD 2010 -> 2014)
I created a macro to insert layers with a click of the button. I was wonder how I get my macro to add the linetype to it. Also would like a separate macro to make the layer not to plot.
Here is the Macro I'm using: ^C^C-layer;new;A-ANNO-AREA-IDEN;color;6;A-ANNO-AREA-IDEN;;
i had been using autocad for almost 10 years now and i always have the newer version for my line of work.
i am having trouble with the excessive styles that shows whenever i copy and paste then the problems occur after that most often. copy paste problems, fatal errors, and my computer hangs most of the time.
I have a polyline in my drawing, consisting of arcs and lines all joined together. It is a waterline and I cannot get it to reverse.. it is reading ----M----- instead of -----W-----
I have a storm linetype that looks like this"---STM----------STM----------STM---". The STM text within the linetype is reading upside down since it is placed past the 90°mark (i.e. from 11 o'clock to 5 o'clock).
Tried blocking the line out and rotateing.
Tried grouping the line and rotating.
Tried reverse comand.
Tried joining a line to it to trick it into fliping.
we use a custom treeline for all our drawings and as of late we can not publish this line type. The tree line will plot fine if you plot the individual pages but when you try to publish and plot all the pages as a group, it plots the tree line as a dotted line. I checked the plot styles and it's set to use object linetype. Like I said though it only seems to have this problem when publishing the drawing