I have a small site where i've essentially designed a storage pond. I've cut 3.0m off the original ground at a 2:1 slope and built a berm at a 2:1 fill slope to a designed elevation. I've managed to balance the site to zero. The contour drawing I have shows elevations - which is great - however the client has asked to see the contours showing a Fill or Cut label from the original ground.
View 5 RepliesI can create pond quick profile,but it can not be saved.
if I press the section view command ,it tells me no alignment .you know ,I only create pond without any alignment .I only created pond by grading .so I don't know how to create pond section.
I have a manure storage pond that I am trying to figure out the total storage volume for. It has 2.5:1 Side slopes and a 10 foot wide ramp at 10:1 entering the pond to the floor bottom. I am trying to figure out what the volume of this pond is. What is the fastest and most efficient way to get this volume? I do not want it compared to any other surface such as existing ground.
View 7 Replies View RelatedI have a surface and i have the outer border of a pond i want to create (see attachments). What makes it difficult for me is that different areas of the pond have different slopes. The area marked as "A" has a slope of 1:5, the are has a slope of 1:2 and the rest of the pond has a slope of 1:1.
My problem: I do not know how to grade the borderline so i end up having a surface with different slopes as my pond.
How to open subassembly designed in SAC 2013 in the SAC 2012 ?
Civil 3D 2012, SAC
16 GB Ram 64 Bit Win7
I have a surface built for the bottom of a pond. The way to get the surface area (not the volume) of the bottom of this pond?
View 2 Replies View RelatedI have 2 feature lines, one is at elevation 132 (TOB), and the other at 123 (TOE). I inserted elevation points at an increment of every 3 ft., which should make a smooth arc of contours around the pond.If the issue was resolved by this method, please click on "Accept As Solution".
View 9 Replies View RelatedI am trying to add an entry point to a retention pond that was created by grading tools. I will to entry point to be shaped like a trapezoid. I also want to grade a entry point to the slope of pond to control water erosion.
I have been trying to add the entry point for days.
I am designing a retention pond in an existing surface. I set the base of the pond and execute the grading at the desired slope and it generates the pond just fine, with the exception of rounded corners. I need the corners to be square, mitered corners instead of the round.
I'm using Civil 3D 2013.
I created a Pond Grading object with the associated surface. How can I cut and plot Section Views of the Pond Grading object just as I could do(using "Create Multiple Section Vtews" command) with Corridor object of a Linear project?
View 2 Replies View RelatedAfter crating my squared pond (or waste landfill for that matter) I runned a cross section from an alignment running across the the entire pond. The cross section did not show the bottom of the pond. I noticed that I forgot to do an infill to the bottom of the pond so I did it. But, still the bottom of the pond its not showing up in the cross section, just the side slopes. Do I have to delete the alignment across the pond and recreate it? That is probably the only thing I have not done. BTW, I have an access road coming down the side of the pond with a corridor created already and is not showing up neither on the cross section.
PD: I am running Civil 3D 2012!
Attached is my 1st project using SSA for detention pond design.
Where is the best place to view the results for the detention pond peak outflow and maximum HGL?
Also, the program seems to separate the results per year storm...anyway to view the results for all year storms in the same report?
how do you attach the .spf file?
2013 Civil 3D
I have a site, on which I've created both a berm and a retention pond to contain runoff. I now need to see if this is retaing enough water at a certain surface elevation.
The existing site is one surface and the berm/pond are another surface.
Is there a way to do this?
I have recreated two surfaces for my design, existing and proposed. I had used polylines for contours for in each surface. I tried labeling the contours but it will not let me select the contour itself.
I then tried to make the contours to 3d polylines and again added them to the surface and rebuilt. I still am not allowed to label the contour since it doesn't let me select the polyline. I am able to select the surface however.
how to create a section view for a pond other than quick view.
View 2 Replies View RelatedAny way to label a pipe part way between structures? I would like to be able to label a sanitary line where a service ties in with the main line invert.
C3D 2013
I read through the previous posts but still I am not able to do this. I am using C3D 2012.
What I need to do is label Deflection angles of an alignment (delta angle). The alignment does not have any curve.
So basically it will be some kind of PI or geometry point label showing the deflection angle.
Labelling LT or RT would be great but at this time I dont need that.
I hope it explains.
I want to label the surface sections (eg, fg) in a single location something like what is shown in the attached image.
Currently I am using a major offset label which refers to the surface description* where the surface name is stored. I set the increment to a suitable number which results in multiple labels along the section. I then drag one into position and delete the rest using ctrl-select. While it would be far easier to use multileaders to acheive the correct look, they don't update location with the section views.
We use the description to store the 'friendly' name as our object naming standard wouldn't necessarily make sense to the viewer of the plans.
I am labeling structures in a network on the profile view. I cannot get the leader when i drag the label to anchor to the top of the structure? Is there a way to do this, i figured out how to have the label insert at the middle of the top line of the structure.
Civil 2014-Infrastructure Design Suite
Windows 7 Professional-SP 1-64 bit system
Intel Core i5-2500K cpu @ 3.3ghz
NVIDIA GeForce GT 430
8.0 gb ram
how label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
I'm running 2012. Is it still true that I need to label my contours in every drawing? I have a drawing that contains my existing surface (about 90 Acres). I have labeled the contours in that drawing. I then have a output drawing that the existing contours are a data shortcut. The contour labels do not show up.
View 3 Replies View RelatedLabeling lines with their azimuth, I wanted to label lines with their azimuth but sounds not to work. I got question marks instead (attached)
View 9 Replies View RelatedOften I've found myself dealing with some pretty complicated surfaces that have a lot of nooks and crannies, and many of the contour lines are only in a corner of the surface or are small and closed, and thus when I find myself wanting to have contour labels on all of the contours, there's not really one line I can draw using the "Create Multiple Labels at Interval" option to ensure that every contour is labeled. Thus I end up doing "Create Multiple At Interval" with a few different lines intersecting contours, but I often end up hitting some of the contours multiple times and I get a mess of labels.
I haven't been able to find a way to automatically just multiple labels on all of the contours at an interval in one fell swoop, so I started trying to program one...but then I got stuck with that, too.
Does any built-in method of doing what I want to do, or do I need to continue pursuing a programmatic solution?
How can I make better the second labeling precision in Civil 3D? It's only has four digits precision for the seconds. I did change the ambient settings (Lat Long precision to 8) but haven't got the result.
View 4 Replies View Related I have a drainage model, the data for which has been imported from microdrainage into Civil3d (.sws file) .
The engineer working on the project is playing around with the Invert and Cover levels so I reload the same updated .sws file into my model almost daily expecting the information shown in the labels of the pipes and manholes to simply change. Instead mine seem to disappear and I have to relabel the whole network again.
This wouldn't be much of a problem because labeling only takes a few minutes but with this particular scheme, the client wants the labels shown in a box with a leader. When I relabel, the boxes automatically snap to the center of the manholes without a leader and i then have to drag each one away from the manhole to get the leader to show up.
Where do I set the contour labeling line to not show or be on layer defpoints. When I click on the label line and right click I can edit the contour label line properties and change the Display contour label line to false but not sure where the style is.
View 9 Replies View RelatedIs there away to label (Dynamically) slope arrows and percents on a tin surface (Without Exploding it)?
View 8 Replies View RelatedHow can I show the description (in this case, MUDSTONE) in a profile label? I've tried modifying the style but the description refuses to appear even though it is one of the available labels.
View 3 Replies View RelatedWhen I draw in the profile layout I'm getting odd results when the labeling is placed. See attachment. I have been looking through the styles trying to find what is wrong.
View 9 Replies View RelatedEverytime I use the label line command, when I go to plot my drawing I see a box around my label and the label is either chopped off or missing. A rectangle prints out around where the label is.
View 9 Replies View RelatedIs it possible to ask Photoshop to save TIFF images using tile internal storage rather than strip storage? A little-known setting, a registry patch perhaps?
View 2 Replies View Related