AutoCAD Civil 3D :: Can't Get Pastel Colors Assigned To Surface Range
Oct 5, 2012
I have a volume surface that I want cut & fill displayed with elevation banding. I created a surface style and chose pastels for the color scheme. When I analyze the surface I chose elevations>> range interval with datum and I get 2d solids but they are not pastel even though the style assigned is the one I mentioned.
How do I get the colors to be pastel?
Civil 3D 2012 & 2013
HP Z210 Workstation
Intel Xeon CPU E31240 @ 3.30 Hz
12 GB Ram
View 9 Replies
ADVERTISEMENT
Oct 31, 2012
Is there a way to automatically adjust the cut range colours (REDS) in the attached scheme such that the lighter colours denote lower cut depths in the same way that the fill range does (Greens)
I know they can be manually adjusted but when the analysis is run again the colours revert back
(No connection with Autodesk other than using the products in the real world)
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 5 Replies
View Related
Apr 2, 2012
I've got a number of scenario diagrams to produce where I want to show the volume of material to be dredged from a harbour. There will be no "fill" just cut. In some parts of the area of interest the existing ground is below the target depth, so these holes wouldn't need to dredged further.
Two question:
1. Given that the area in question contains cut areas, but also other areas that I don't want to fill. What is the best way to get a good surface map and volume estimation? Currently, I create a feature line surrounding the entire area to be less than the target depth, set the elevation of the line at that depth, then grade to surface and add an infill. This gives me cut and fill volumes (for the deep holes), of which I ignore the fill number. Is there a better way??
2. I've created my TIN volume surface (comparison of EG with the graded depth surface). Now I want to present the maps with "range interval with datum", so the cut volumes are shaded increasing from (say) yellow to red, whereas for the "fill" areas I don't want to show anything (transparent would be ideal or maybe greys). Is there a way to create customised color ranges for the elevation analysis? As I'm doing numerous maps I don't want to be manually editing and re-editing the analysis range details. I'm using AutoCAD C3D 2012.
Civil3D 2013 (infrastructure suite)
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), GTX680, Win7Pro64
View 9 Replies
View Related
Sep 17, 2013
I change my surface style to slope banding (3 ranges) and make a legend table.All of the three ranges in the table are red and my surface ranges are blue, yellow, & red.
View 9 Replies
View Related
Nov 29, 2012
Is there a way to lighten up the colors of my surface slope analysis that the rainbow gives me? My drawing will be going into a report and the colors are too bold. Pastels are a bit too bold.
View 9 Replies
View Related
Jun 24, 2013
I have a surface with all sorts of heights, and want to add color to different heights. Getting the color there is not that difficult, but how do I swap them around? i.e. red is 'low ground' and blue is 'high ground'. In Holland we use it the other way around though, so blue should be low ground and red high ground.
Where exactly do I change this? I've tried it in the surface style tab, surface properties tab, analysis tab, and some others, but no success so far.
View 9 Replies
View Related
Sep 14, 2011
When I import a STEP file or most recently a Solidworks part the assigned colors are replaced by the standard gray. Is there an option I'm missing to ensure the colors are retained? I am using Inventor Professional 2012.
View 9 Replies
View Related
Dec 15, 2012
Is there a way to create hatching for the slopes surface style instead of using solid colors?
View 2 Replies
View Related
Apr 18, 2013
in Corel X6, some spot colors, either pantone,custom or others, after re-opening files, these colors appearas NO NAME, and the object assigned to them appear withno fills?It never happens with RGB or CMYK colors.
View 1 Replies
View Related
May 14, 2012
Is there a way to change a range of colors to another. Let say I want to change a pic with different shades of red to blue. Which tool would do the trick?
View 1 Replies
View Related
Jan 3, 2013
When assigning a coordinate system to my drawing in Civil 3D 2013, the drawing does not retain the selected system.
I choose the coord system I want in Map Setup and apply it (in this case MT83IF). After applying to the drawing I go back to verify the selected coordinate system and the dialog box indicates "N/A". The only workaround I can find is to save the drawing back to an earlier version and open it on another computer in the office that is running 2011. There I can assign my coord system and then reopen in 2013 where it now shows it properly assigned.
I have tried other coord systems to make sure it isn't isolated to just the one I am selecting - and it happens with all others I try. I have also tried a repair on my install to see if that would correct it to no avail.
I have a 64 bit system and have installed all service packs to date.
View 3 Replies
View Related
Sep 28, 2013
What is the best way to insert a c3d point with assigned values. For example, I want to insert a point with the style curb stop, on a certain layer with a certain label. Going through thr insert point tool is not very user friendly for users looking to add points, not assign properties. Can this operation be added to the tool palettes? I am not familar with creating my own.
C3D 2012 or 2014
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
View 6 Replies
View Related
Oct 30, 2013
I would like to replace a range of colors with a single color in an image.
I know there is the replace color adjustment, but this replaces a single color e.g. 190,190,190 with another color e.g. 200, 200, 200. I would like to replace a range of colors e.g. from 185 to 195 with 200, 200, 200.
View 1 Replies
View Related
Jun 6, 2012
I'm setting up some computers for training some new users on Civil 3D 2011 and Im having problems with importing points and creating figure lines, works great on all the computers in the office, but in the training room can not get the figure lines to assign to the proper layers. They all go on the zero layer. All the setting I see are the same.
View 5 Replies
View Related
Jul 15, 2013
Is there any way to change a Profile Type that has "File" assigned to it to"Layout"?
C3D 2012 SP3 & C3D 2014 SP1
Win 7 Professional 64 Bit
View 9 Replies
View Related
Feb 12, 2013
When I import points from a survey database there is a very large new number being assigned to points that have overlap/numbering conflicts.
I had some survey from one source that was in the 1000 pt # range & additional survey that was in same numbering sequence.
When importing the points I chose "Resolve all" it is renumbering the Point number value to the 5xxxxxxxx range?
Is there some setting where I can change this to a lower # or how/why this is happening?
Next Point Number value @ Settings Tab>Point>Commands>CreatePoints>Point Identity>Next Point Number = 3.
I've attached a couple of captions illustrating the issue.
2012 Civil 3D SP 2.1
Win 7
C3D 2012 SP3 & C3D 2014 SP1
Win 7 Professional 64 Bit
View 4 Replies
View Related
Apr 19, 2012
I am using C3D 2012 and i know how to create a table showing volumes for different elevation ranges with different colours, but how to show the total cut or fill for the volume surface in the same table so that you dont have to manually add up all of the cuts or fills? or have to display only two ranges?
View 1 Replies
View Related
Sep 13, 2012
During an import event I get a warning message saying the Angle is out of Range. The .fbk text below is where the import is getting hung up, the red text is the specific line.
F1 VA 23211 260.52200 84.640 90.32060 "HWC1"
F1 VA 23212 260.10119 86.282 90.31600 "HWC1"
F1 VA 23213 261.27140 84.380 90.15160 "GS"
View 3 Replies
View Related
Oct 24, 2013
I am trying to insert an excel table using a datalink. If I insert the entire sheet, it includes too many cells. If I set a print area and choose that area, it will not insert the table. The first time it acts like it is going to work, but then never lets me place the table. The second attempt it just will not let me select that data link. If I actually name a group of cells, I get the same behavior as the print area. Have issues with importing excel tables? Am I missing a step?
My work flow is
Create an excel sheet & format the table.
Select desired sells, set print area.
Save & Close excel
go to annotate tab in civil 3d
select table icon
choose from data link
launch data link manager
create data link and choose range of cells as print area.
Press OK
it never let me choose insert point.
I have also tried to simply make the datalink and then run the table command with the same results.
Civil 3D 2013
HP Z400 Workstation
6GB of RAM
296GB HDD
ATI FirePro V5700(FireGL)
Win 7 Home Professional
View 5 Replies
View Related
Jul 10, 2012
I have a sidewalk project with 5' wide sidewalk and the edge of sidewalk is 5' of the back of curb. All is fine and well, I have link slope to surface subassembly assigned to one side and a link offset and slope subassembly to the other side of the sidewalk. Everything daylights nicely.
Here is the issue......my link slope to surface subassembly is an 8:1 slope to tie into the existing surface model. There is one stretch of sidewalk where I have a retaining wall behind the sidewalk for about 15'. My section views are every 10' and in one of them the wall needs to show up. I could use the link vertcial sub assembly in this area but I am not sure how to use a specific subassembly in one area. Do I split that region up in my corridor, create a new region to use that references a new assembly to use in that 15' strectch which would contain the link vertical subassembly? Or, do I create the link vertcial subassembly in my current assembly and assign a station range to it so it doesn't show up throughout the entire corridor? It's like I wante to transition in and back out of a subassembly. Incidentally, I have one assembly used for the entire length of my project.
View 1 Replies
View Related
Dec 2, 2011
I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
View 6 Replies
View Related
Oct 22, 2012
Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
View 9 Replies
View Related
Feb 25, 2013
Modifying the point size/text size assigned at particular annotation scale,
I’m wondering how the point size/text size assigned at particular annotation scale can be modified.
For example, in the attached screenshot, the point size assigned at the annotation scale of 1/1000 is big and I wanted to make it a bit smaller at that scale.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
View 2 Replies
View Related
Nov 14, 2012
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
View 5 Replies
View Related
Dec 10, 2012
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
View 2 Replies
View Related
Oct 2, 2012
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
View 9 Replies
View Related
Apr 4, 2012
Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011
View 1 Replies
View Related
Jul 29, 2013
I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.
The questions:
Would it be better to import the surface into Revit to merge surface and buildings together?
Would it be better to import the buildings into C3D to merge entities?
Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?
View 6 Replies
View Related
Dec 7, 2013
You can see in the attached screen cap that colors 1-9 appear as white on my screen and that colors 10-22 are not correct either. This is only occuring in one specific drawing. Is there a preference that I switched somewhere that would make this happen? I have double checked that everything is ByLayer or ByColor that I can think of. If I insert this color chart into other drawings it looks fine. using C3D 2012.
I would just restart my drawing, however it is the new company template file that I have invested many hours into and would really like to be able to keep working with it and not start over. Or is there a good way to import and overwrite all the Prospector settings into a blank drawing?
View 4 Replies
View Related
Sep 15, 2013
I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.
i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline. This seemed to work, but when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.
View 3 Replies
View Related
Mar 1, 2013
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
View 9 Replies
View Related
