I can edit the cleanup in place just fine and in plan all is good, but in 3D, the height of the modfied region is not the full wall height, just some random height.
View 4 RepliesWhen building wall styles and configuring cleanup priorities for components, what is the methodology? Do I sketch out a bunch of scenarios of various wall styles meeting each other at Ls and Ts and crosses and whatever, and then try to puzzle it all out: "if I set the outer airspace to 400, then when it gets to this T, the airspace will cut through the rigid insulation with its 600 priority, but will get cut through by the sheetrock with its 200 priority....". That seems like a recipe for headaches. So instead, do I just start from one side of a wall (the wall with the greatest number of components, I guess) and assign the lowest priority number (300, say) to the structural component, the highest number (1200, say) to the finish material component, and numbers in between for everything else, and then see how it works, tweaking by trial and error? The table of priority numbers for various materials provided is useful, but I'd like to have a better understanding of how those numbers might have been derived, so I can do a better job of assigning my own numbers to components that don't appear in the list.
Also, if a wall type contains two components of the same material (I'm thinking of the layers of rigid insulation on either side of the concrete in an Insulated Concrete Foundation system), should those two components have the same priority number (probably not), or different ones (seems more likely)?
We just upgraded from ACA 2011 to ACA2012 and we are getting some wall cleanup issues with foundations. some walls, the footings show while adjacent wall (same style) footing disappears.
also, when i copy a wall where the footing is missing, the new copied wall shows the footing. when i move a wall without a footing, the footing shows up.
I am using AutoCAD Architecture 2011.
I have a complicated interior area where my walls can't clean up properly even though they are located in the right place. The wall is located at the center point of two columns which are all drawn as metal stud walls and gyp board with correct material cleanup priorities. I have a curtain wall anchored to the stud wall with sill height of 1'-4" and head height of 10'-8". I want to see the wall show up below and above the curtain wall which it does in axonometric view, but in plan, the cleanup error hides the wall completely. The fact that the wall below the curtain wall doesn't show up in plan is not the main issue, I just want to know if this wall will be able to take part in the conflict resolution I will be running later in the model or will it not because it has a cleanup error?
When I try edit block in place this error occurred:
Errors found in references to other objects:
Object reference missing: AcDbXrecord, to AcDbBlockTableRecord
Cancel
I'm getting very long run times to edit x refs in place. Once the exref drawing opens, sometimes after 2 or three minutes, and I make my edit, It can take ten minuted to close the xref.
Drawing are clean, purged, -purged, recovered audited. Computer is new workstation and dedicated to CAD only. Very little opportunity for corrupted files.
I know I can probably overdraft this in 2-D; but is there a way to clean this up?I'd like to stop the inside finish surface of the roof element, inside the building (horizontal pine boards).I tried the similar trick like a wall base extension; didn't seem to work. (?)I'd like to have the rafter to top-plate seat cut out of the rafter also.
View 1 Replies View RelatedAny way using autoCAD LT 2014 to get CAD to display the elevation heights of survey points without having to type the heights in text bozes next to each individual point. i can insert a field which displays the elevation of the point but doing this again i would have to do every point individually.
Another words is there a way to select all the survey points required and get CAD to display a certain property, which in my case is the elevation height of that survey point, next to it? so it looks like x 23.35 x 23.57 etc..
I want to run one wall just a few inches past another. If I override the Cleanup Radius at the appropriate ends of the walls, setting the radii to a small number (1/2"), shouldn't that allow one wall to be run a couple inches past the other? The attached image shows the end of Wall 2 pulled as close to Wall 1 as I can get it. Both walls have the Cleanup Radius override at 1/2". If I nudge the end of Wall 2 down any further, it jumps down to form a corner with Wall 1.
View 1 Replies View RelatedThe table in the Help that lists suggested cleanup priority values for various wall components does not include sheathing. The table lists 900 as the index for siding, but I assume that's a different number from sheathing. If I have steel studs, then 1/2" sheathing, then 2" rigid insulation, then 3/4" strapping, then wood siding, the priority number for sheathing should be higher than the studs, and lower than the rigid insulation, strapping, and siding, right? 500 for the studs, 600 sheathing, 700 rigid insulation, 800 for strapping (which could also be considered an air gap), 900 for siding?
View 1 Replies View RelatedI have a slab with a edge style for a thicken slab (haunch). I have the materials for both objects identical. When I make a 2d section, the slab on top of the haunch does not clean up with the haunch on the bottom. When I go ACA out of the box slab & slab edge styles, there is a thicken slab (slab with haunch) live section the way it should look. I can't reproduce it even when I bring it in to my drw. from the out-of-box Does it have something to do with 2d section? This might sound simple but I'm just not able to figure it out how to make things cleanup.
View 1 Replies View RelatedI can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
In Revit 2012, how do I place a wall at an angle to the ground plane, so it can be connected to a roof above? I have tried placing a wall on level and rotating it, however it does not appear to work. I can rotate other elements, but not walls.
View 1 Replies View RelatedIs it possible to add a standard wall opening in a wall that i have modelled in place?
I know i can add a void extrusion to the model just wondering if there's a setting i can change to allow me to use the standard wall opening comand.
I used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies View RelatedI am trying to create a sloped wall by creating a mass in-place. First I draw a line on a surface at a pre-determined level that I've set up in elevation. Then I offset this line in the vertical plane. My next step is to offset this second line so that it is not directly above the original line, but offset in the horizontal plane. How do I change from a vertical to a horizontal offset? I’ve tried different work planes, but they all offset vertically.
View 6 Replies View RelatedI quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedIn Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies View RelatedI did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies View Relatedhave trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View RelatedIs it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 Replies View RelatedI have received some architectural models which were modeled in AutoCAD MEP and only have walls modeled as type Standard. Is there a way to transform Standard walls into cavity walls etc., giving wall makeup as you go - or do I have to re-model in order to get quality 2D cuts?
View 1 Replies View RelatedI'm just trying to put a wall under a stair and it seems like I can not succeed. Already tried with interference, body modifiers and trimming.
View 2 Replies View RelatedWhy would a window not go into a wall?
I have a client who is having this issue - when I open the file it works fine for me.
Is there a system variable or setting that could cause this?
I've got a wall style that has multiple components. I have changed one component so the bottom starts 12" below the baseline ht of the wall.The section window display reflects the change, but the wall style won't update.Is there a setting I'm missing somewhere.
View 2 Replies View RelatedHow to group wall types together when scheduling a drawing?
I have multiple wall types within a drawing but scheduling produces multiple entries per type depending on length, only grouping them together when lengths are identical. All I need is a total length per wall type within the drawing.