I have received a drawing from a consultant that appears to be locked to a plan view. How this has been done and I would like to switch it off.
Just to be clear it is locked in the modelspace tab not a viewport.
I am trying to insert blocks into my drawings and for the most part I have been successful using Design Center. However, I have difficulties turning some of those blocks from the Plan View into the Elevation View, even when they show as elevation blocks. Even the downloads that show as 3-D end up being inserted as 2-D in plan view. In floor plan mode, I have no problem; so how do I turn them into 2-D in elevation mode?
View 1 Replies View RelatedI am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
View 7 Replies View RelatedIs there a way to align a modelspace rectangle to viewport extents in paperspace? My situation is that I have several page 'layouts' (complete with paper size boundaries and title blocks) drawn in 2D modelspace, as this is how I have been plotting up until now. I am trying to set up these 'layouts' in actual paperspace Layout Tabs for batch processing, and I would like a way to position my view within a viewport so that the recatngle that I have drawn in modelspace snaps to the viewport extents. I am sure this is a 'day1' type of question, but I'm very new to paperspace Layouts.
View 4 Replies View Relatedi draw up all of my walls, i connect them properly, cleanup etc. then i want to trim them with my roof slabs and what i see? i see my walls suddenly dissappear in 3d view but are still correctly shown on plan view? i know it has something to do with roofline because when i tried to project them automatically to ontu my roof slabs the walls dissappeared too!
View 1 Replies View RelatedI was given a horizontal centerline of a 5 mile bike path. We have to stake all the even stationing every 50 feet and all the VPC's and VPT's with vertical elevation. I have created the horizontal profile and also the vertical profile including all the vertical curve information. Is there an easy way to incorporate the elevation information back into the plan view so I can create points that carry x,y & z points that I can transfer out of autocad as a .txt file so we can upload it on our gps equipment?
View 9 Replies View RelatedIs there a way to easily add an object from a profile view to a plan view? I have developed a pipeline profile that has high and low points and I would like to show these points on the plan views.
View 9 Replies View RelatedIn modelspace I have a drawing that is aligned perfectly, but when I create a new viewport in a layout the drawing that was created in modelspace seems slightly rotated in the layout view?
View 3 Replies View RelatedResidential custom home design. I come from the good old fashioned background of pencil and paper drafting. Although with the recent technology advances I have migrated to the AutoCAD side of the fence, and loving every minute of it. Upon purchasing a copy of AutoCAD 2004, I continued drafting the way I knew how, lines on paper. I have recently upgraded to AutoCAD 2007, and with no formal training, I am looking in drafting in 3D.
My main question has multiple parts;
What is the best way to draw walls in 3D?
What is the best way to add windows and doors? and is there a way to have the "plan view" relate with the "elevation view"?
How do you go about adding a roof?
I have played around in the isometric views attempting to solve the previous questions, although I have been doing all of it with line work. I know there has to be an easier and more efficient way of going about this....
We have our first project in Revit that we are having to split among multiple sheets because of the size of the building, so I have made 3 dependent views from the main overall view, named them, cropped them and placed each part (A,B, and C) on separate sheets. Now that I am trying to do enlarged toilet plan views, I want to tag the plans with the plan callouts on the 1/8” sheets that are the dependent views, but all the view tags are referencing dependent view A since it is the first dependent view in the list. If I change sheet A to be named Sheet X for instance, all the view tags now reference sheet B since that becomes the first dependent view alphabetically. I want them to reference the sheet they appear in, but I can’t seem to figure out how to do that, even though they are in different dependent views completely and within the crop region, they all default to the first dependent view in alphabetical order.
View 4 Replies View RelatedHaving issues plotting. I have a sheet with 3d piping in plan view, viewport is set to Legacy Hidden as always. I have a 3DCLIP plane set to only see pipe at a certain elevation. When plotted, some of the pipe lines are missing. If I change the viewport display view, then the piping is fine but random objects show up that shouldn't b/c of my 3DCLIP plane.
View 0 Replies View RelatedI have a message pop up when i am trying to save an assembly. it is:
'The current Design View Representaion is locked. Changes againstit will not be saved. If you want to keep those changes please create a new Design View Representation or unlock the current one.'
How can I Unlock the Design View Representation?
View 5 Replies View Relatedthe panorama vista in one of my users civil 3d 2012 is locked in place and cannot be moved.
View 2 Replies View RelatedA problem we are having in our office on 1 computer is that this message appears in the command line
'viewport is view locked switching to paper space'
It happens whenever we zoom or pan into one of our locked viewports. We have purposefully locked the viewport so we don't lose the scale when we zoom or pan and want to leave it this way, however, whenever we zoom or pan this message appears and it takes 30 seconds before the screen readjusts to the zoom or pan we require.
I have had this issue for about two weeks. I am not aware of any changes to my system though Windows 7 updates automatically.
Often, but not all the time, when I am in a floating viewport which is locked and I zoom in, the part of the drawing disappears as if the view on the viewport has adjusted to one side so that I cannot see any of what I am working on. If I escape the command and 'undo' last command it takes me back to the correct view but in paperspace.
This is a pain as I cannot zoom in to locate a point accurately. It only happens when I zoom in quite close. The viewports are locked and it is only a problem recently. I have used CAD for 20 years and LT 2008 for the last 4-5 years so I dont think it is a user issue. Maybe a settings issue or bug, but I have not knowingly changed any settings which would do this and cannot see why this would be a 'feature'.
Are there places where I can find plan view furniture pieces for AutoCAD 2012? I have found some, but most are commercial. I'm looking for residential furniture like sofas, loveseats, and chairs in victorian era styles.
View 1 Replies View RelatedAutocad Architecture 2012: my dwg is fully visible in 3D View but partially visible in plan View. What could be causing this problem? See screen shot attached.
View 4 Replies View RelatedI am simply xref'ing a profile drawing into a sheet drawing to print out. AS shown on the attached, when the profile comes into the xref I lose all the band data and the EG line does not come in as a dashed 2 line as the layer is set to. It almost looks as if the PL linetype generation is off for this line.
View 1 Replies View RelatedI found super elevation labeling for profile, but not for alignment in plan view. Is there a way to label alignment, f.x. in critical points of super elevation automatically?
View 2 Replies View RelatedIs there a way to make 3d view of an object ( say a box) from its plan and elevation? I'm requesting you to all to get a solution.
View 9 Replies View RelatedI am using AutoCAD Architecture 2011. I've inserted 3 windows in an exterior wall. They all can be seen in Plan (top) view. I've gone back and changed the height of the windows. Now when I look in Plan (top) view, the windows I've changed the dimensions on are no longer visible.how to make these windows visible again in plan (top) view?
Note: These re-sized windows can be seen in any other perspective except Plan (top) view.
I need drawing a set of winder stairs in plan view. I am using autocad 2008.
View 9 Replies View Relatedi have some simple profiles and just want to show the pvi's in plan view on the alignment.
i made a reference label and it works great. now i am trying to figure out if there is a quick way to locate the pvi station on plan view other than doing something like create a point using sta. and offset as parameters hand typing in the info.
Is there a way to label corridor links in plan view ?. I would like to show my pavement cross slopes from corridor in plan view.
View 5 Replies View RelatedI've been using autocad 2012 student version and all the blocks I've used in my dwgs up until now, is blocks I created myself or blocks that I get from someone else. Now, I've been told that autocad comes with a library of blocks in plan and elevation view. How do I access them?
View 9 Replies View RelatedHow can i get Floor plan etc to drafting view whitout export to Auto cad and back to revit 2012?? Or freeze a Floor plan will be okay.
View 2 Replies View RelatedI'm working with plan production sheets and having some trouble. My vertical exaggeration makes me want to split the profile, but when I do it, they get glued together. My left vertical grid numeration stays on the middle of the grid and I get a lot of information overlapped. What I need is to put some gap between these, or split'em. Other issue is that the axis offset of my Profile Style isn't being applied, as well as other configs.
View 2 Replies View RelatedIs there a way of adding superelvation data such as full superelevation cross slope to an alignment curve label in plan view?
In my case we add a label for each horizontal curve with critical curve data such as PI Station, Delta, Degree of Curve, etc... but I can't seem to find a way of adding any superelvation information to the plan view as a label. Ideally I would like to be able to add the maximum cross slope value and superelevation critical stations to the label.
There is a way of adding the superelevation critical stations a labels to the alignment similar to how PC's or PT's are labeled, but it does not give the cross slope value.
From my project manager > views, I select a view, it opens in model. I change to paper space and have my plan and an isometric view (in wire frame). I go to view and select shaded with edges. Perfect, colors on both plan and isometric are where I want them, now I want to print this.
I select my print icon and change my paper size select my printer. I select extents, center the plot and fit to paper. I preview.. And my color disappears. What.. Am I doing wrong. Should I be making my paper representations from a different start?
Yesterday.. I was trying to do the same thing.. But starting with the drawing in constructs. I end up with the same, my isometric drawing looses most of its color, the windows have color as does one layer (a line showing the outline of the floor under). The plan drawing has most of the colors but some of the layers are black where in the model they have color. To further complicate the problem.. The same procedure making a first floor drawing has the plan in complete color.
I placed walls at 12'0" elevation as they wereconflicting with walls below (overlap). I can't see them in plan view - In 3D iso view they are visible.
View 4 Replies View Related