AutoCAD 2013 :: Midpoint Of A Line
Apr 25, 2012Say you have a square and you want to draw a line from the midpoint of one side to the other, can you set something so that it tells you when you are exactly on the midpoint of a line?
View 9 Replies
ADVERTISEMENT
AutoCad 2D :: Midpoint On Line Not Visible (Grips)
Aug 23, 2012on my work pc i'm missing two features i used to have:
- Firstly, when i click a PL i can't see the midpoint of the line, and can't drag the line like i used to. I tried to change GRIPS, but can only choose between 0 and 1 when choosing grips. 0 being nothing visible, 1 being visible endpoints of the polylines. 2 is NOT valid options that i can choose.
- I can't add a new vertex. I think the way i used to do it was to hover over the midpoint and it would suggest if i wanted to add a new vertex. If this is the case, it's obvious that if i get problem 1 fixed, problem 2 will solve itself.
AutoCad 2D :: How To Dimension Midpoint Of One Beam To Midpoint Of Another One
Apr 21, 2013Im trying to dimension the midpoints of a series vertical beams thats perpendicular to the x axis. How to dimension the midpoint of one beam to the midpoint of another beam?
Normally i just select dimlinear and then ctl + right click "mid between 2 points", but this way just seems time consuming when you have a series of them to do, is there a better way to dimension a series of beams from one midpoint to another midpoint?
AutoCAD Inventor :: Unable To Snap To Sketch Line Midpoint
Nov 26, 2012When I use a tool such as 'move'/'select base point' in the sketch environment, I used to be able to select line midpoints.
Is this no longer possible? My constraint options seem to be fine.
Recently upgraded to 2013
Revit :: How To Place Midpoint Of Window On Midpoint Of Wall
Oct 1, 2012How to place the “midpoint” of window on the midpoint of wall?
In the screenshot below, I wanted to place the window from its midpoint to the midpoint of the wall. How this can be performed on Revit?
AutoCAD 2013 :: Pick An Existing Line To Create A New Line With Current Layer?
Sep 12, 2013For example, I'm making revisions to a plan and drag a block or xref of the floor plan changes where walls/doors/windows have moved. I want to be able to simply pick the underlying linework as opposed to tracing over each line of said xref/block.
View 8 Replies View RelatedAutoCAD 2013 :: Select Line Then Enter Command - Line Unselects
Jun 28, 2012if I select a line, then enter the move command, the line unselects also when I select a line, then hit delete, the line is still there both of these used to work
2013 Civil 3D
AutoCAD LT :: Unable To Find Midpoint
Dec 22, 2011I can't snap to a midpoint in a line. For example, If I draw a line 10" long, I can't draw a line from the center of that line. It used to give me an auto snap option to go to, but now it only allows me to snap to the ends of that line.
View 6 Replies View RelatedAutoCAD Inventor :: Sketch Dimensioning - Midpoint
Apr 30, 2013It must surely be in there somewhere but I cant find a way to dimension to a line's midpoint in a sketch.
View 3 Replies View RelatedAutoCAD Inventor :: Turn Off Midpoint Snap?
May 16, 2006IV11, IDW.Is there a way to Disable Midpoint snapping while Dimensioning?It seems to get in the way a lot.A lot of the Lines i have to dimension are small and it's Always trying to dimension to the Midpoints of them rather than end points.Not a bad concept.. just in my case it really gets in the way..So just wondering if there is a setting somewhere to turn it off?
View 9 Replies View RelatedAutoCad :: Dynamic Block Midpoint Snap?
Nov 7, 2011I'm new to working with dynamic blocks, using AutoCAD 2007. I have a base cabinet elevation block and want to have it so that when I change the height the door swing line stays at the midpoint of the door.
View 9 Replies View RelatedAutoCAD 2010 :: Mirroring From Apparent Midpoint?
Mar 22, 2013Is there a command out there that allows you to mirror objects from an apparent midpoint from like an otrack without physically drawing a line then having to erase it later? I thought there was a way to do it, but my memory is failing me.
View 1 Replies View RelatedAutoCAD Inventor :: Add Sketch-point To Midpoint Of Arc?
Mar 16, 2012How would one add a sketch-point to a midpoint of an arc? For a SketchLine its easy...
oSketch.GeometricConstraints.AddMidpoint oSketchPoint, oSketchLine
However, I can't see how to do the same operation to find the midpoint of a SketchArc. The interface of course has a selection filter for this so I assume the API can do the same?
AutoCAD 2013 :: Draw A Line From End Of Line To Start
Jul 31, 2013I was drawing a lot of lines with the pointer that stuck at the end of the line and after that it stuck at the beginning of the other line (i hope you understand what i mean). I don't know what i pressed but now this function is not active and is very difficult to draw the lines.
View 3 Replies View RelatedAutoCAD Inventor :: How To Obtain A Vertex From Edge Midpoint
Nov 7, 2012I need to define a mate constraint with a workplane as EntityOne and a midpoint from an Edge as EntityTwo.
API-Help tells me valid objects are planar faces, linear edges, vertices, cylindrical faces, conical faces, spherical faces, revolved faces, work planes, work axes, and work points.
The Edge object gives me StartVertex and StopVertex, but what about the midpoint?
AutoCAD Architecture :: OSnap Endpoint And Midpoint Does Not Work In Display Set
Sep 1, 2010I'm electrical and have my own display set oddly enough named "electrical". When I set the display to "electrical" I can't osnap to endpoint or midpoint of smart walls in the background (nearest works fine). When I change the display to something else, generally it works.
Is there an "osnap" setting for displays?
AutoCAD Inventor :: Create Work Point On Midpoint Of Curved Edge
Apr 1, 2013Is it possible to create a work point on the midpoint of the curved edge of any feature.
I was not able to access the midpoint of an edge.
Config :: Intel (R) Xeon (R) CPU E31245 @ 3.30 GHz, 16.0 GB, 64bit win7
Inventor 2013 and Vault Basic 2013
After Effects :: Aligning / Landing CC Page Turn To Midpoint
Aug 24, 2013I'm having quite a bit of trouble with achieving a desired effect with CC Page Turn
I'm attempting to make it look as if an open books page is being turned with the centre of the book acting as the Page Turns limit.
When I pull the fold position out fully the page lands way out, I've toyed around with the layers anchor point, and adjusting keyframes of CC Page Turn halfway but no success.
I've included a quick gif to indicate where all is going wrong. I basically want the page to land flush on the left side
AutoCAD 2013 :: How To Label A Line
Aug 8, 2013I can dimension a filleted line. I want to show total length of filleted line.
View 2 Replies View RelatedAutoCAD 2013 :: DWG TO PDF - Line Weight
Apr 26, 2013When i convert to Pdf the line weight is very board on the pdf, I have never had this before.
View 3 Replies View RelatedAutoCAD 2013 :: Cut Line Command?
Apr 13, 2013I've been searching for a command that could actually cut lines for purpose. For example, if I'm drawing a 2 line crossed, wish I could cut the 2 lines so they are now 4 segments. On a circle, I could actually draw a line that pass trough the circle on cut it off the way I wish. Does such command exists for autoCAD? Very often, I've many lines at the same time that I wish I could cut with a single one. The problem is that I don't wish to trim 'em and extend (losing time and long process). Sure there is also the div cmd, but this isn't what I'm seeking for.
View 7 Replies View RelatedAutoCAD 2013 :: Snap To Anywhere On Line?
Aug 19, 2013I need to snap to guide lines but the only snap I can get is to the endpoint, which results in some very diagonal lines. I actually have ortho turned on because I need only 90 degree angles. Sometimes I need to move an entire line and I would like it perfectly lined up to the guideline. The line being moved is part of a polyline.
I sometimes do need to start or end at an endpoint but how do I do that then also snap to just anywhere on the guideline while maintinaing a 90 degree angle?
AutoCAD 2013 :: How To Add Text To A Line
Jun 29, 2013For a current assignment I have created a drawing with several property lots. I am supposed to label the lengths of the lot borders. However, I am having difficulty doing this. I would like text to appear on/above the top line of each block, but I cannot seem to find a way to get the curser to appear on the line. My first question is whether or not this is even possible. How to do this online and come up with nothing. Secondly, if it is possible to add text to a line could this text then be centered?
If this is not at all possible, what is the closest alternative method for inputting text on a line that is centered between the lot corners?
AutoCAD 2013 :: Inclination Of Line
Dec 24, 2012How do the inclination for line. For example I need 2% inclination for some length.
View 3 Replies View RelatedAutoCAD 2013 :: Won't Allow To Specify Length Of A Line
Jun 13, 2013I have used AutoCad for a few years and I installed 2013 to my laptop recently.I noticed that I couldn't specify how long a line should be. When I select the line tool and specify the base point and type how long it should be i.e. 3' and a red box appears around the dimension box and the line isn't drawn. I tried not specifying a unit of length and it draws the line just fine. But for some reason it wont complete the line if I specify feet or inches.
View 2 Replies View RelatedAutoCAD 2013 :: Line Type With Two Colors
Aug 6, 2013I need to represent some lines, in model space, that alternate in color, yellow/red, that are "scalable" with respect to different scale view ports in paperspace.
my initial idea was to use two lines, each in which the dash and space between were the same distance, then just offset the yellow/red lines enough for each to fill the others gaps. But, wondering if it was possible to represent that in a single linetype?
AutoCAD 2013 :: Length Of Line On Mouseover?
Dec 5, 2012In previous versions of autocad after I select a line, and put the mouse pointer over a vertex, there would be an on screen number displaying the length of the line. In Autocad 2013 this seems to have disappeared. how to get it back?
View 2 Replies View RelatedAutoCAD 2013 :: Dimension Line Distance
Jan 22, 2013I used direct-distance entry to place the dimensions 3/8 away from the object lines... needless to say, while most horizontal dimensions are 3/8 away, the vertical and inclined dimensions are not. see attached. other than creating construction geometry and physically moving the endpoints of the arrows to the correct location, is there any way of getting this precise and correct the first time i do it?
View 1 Replies View RelatedAutoCAD 2013 :: View The Line Thickness?
May 13, 2013How is it possible to view the line thickness that you have set at the drawing surface? before you polot. I mean drawing and working with the actual line thickness that you set for the layer? and i do not mean using pline
View 4 Replies View RelatedAutoCAD 2013 :: Extending To Line With Z Elevation?
Oct 17, 2012There is a coworker of mine that seems to have an issue pop up in random files here. He is drawing his siteplan on a file received from a consultant, the issue he's having is that if a line has any sort of elevation to it, he can't extend another line to it. He can flatten the line and then extend to it, but if the same issue is tried on any other machine, the rest of us can extend the line without issue regardless of it having elevation or not. The frustrating part is that he couldn't tell the line had any elevation to it until he took the precision value out to 8 digits. The line he couldn't extend to had an elevation of 0.00000004. But as I said, his machine is the only one that has this issue. We are all running AutoCAD 2013 on Windows 7 64 Bit. Is there a setting or variable somewhere controlling this behavior?
View 5 Replies View RelatedAutoCAD 2013 :: Text Overlaps With Line?
Jan 7, 2014The text"shower"is overlap with the line, how can I erase the line around the text.
View 9 Replies View Related