How would one add a sketch-point to a midpoint of an arc? For a SketchLine its easy...
oSketch.GeometricConstraints.AddMidpoint oSketchPoint, oSketchLine
However, I can't see how to do the same operation to find the midpoint of a SketchArc. The interface of course has a selection filter for this so I assume the API can do the same?
It must surely be in there somewhere but I cant find a way to dimension to a line's midpoint in a sketch.
View 3 Replies View RelatedWhen I use a tool such as 'move'/'select base point' in the sketch environment, I used to be able to select line midpoints.
Is this no longer possible? My constraint options seem to be fine.
Recently upgraded to 2013
Is it possible to create a work point on the midpoint of the curved edge of any feature.
I was not able to access the midpoint of an edge.
Config :: Intel (R) Xeon (R) CPU E31245 @ 3.30 GHz, 16.0 GB, 64bit win7
Inventor 2013 and Vault Basic 2013
I was trying to query some sketch points data from a profile Path using code as below. However the program stopped without telling the reason.
Code below:
i = 0;
foreach (ProfileEntity oSourceProfileEntity in oProfilePath) { switch (oProfilePath[i].SketchEntity.Type) { case ObjectTypeEnum.kSketchArcObject: { SketchArc srcSkArc = default(SketchArc); srcSkArc = (SketchArc) oSourceProfileEntity.SketchEntity; // error points[i] = srcSkArc.StartSketchPoint.Geometry; break; } default: { SketchLine srcSkLine = default(SketchLine); srcSkLine =(SketchLine) oProfilePath[i].SketchEntity; // error points[i] = srcSkLine.StartSketchPoint.Geometry; break; } } i++; }
Im trying to dimension the midpoints of a series vertical beams thats perpendicular to the x axis. How to dimension the midpoint of one beam to the midpoint of another beam?
Normally i just select dimlinear and then ctl + right click "mid between 2 points", but this way just seems time consuming when you have a series of them to do, is there a better way to dimension a series of beams from one midpoint to another midpoint?
I use vb.net draw a cube frame (just point and add edge to link points) in 3dsketch. But at the corner, I got only one edge, the others are filled that is a arc is inserted between the 2nd & 3rd edge to the corner point. There is no second edge is extended to that point.
Just wondering why I got the result. There is no fillet command in my code.
I want to concide two points of two different lines.These two lines have been created in two different workplanes with 2D sketch.
View 7 Replies View RelatedI'm trying to contrain the end points of 2 lines using iLogic. I know the end points but I cannot get the values into the SketchPoint object. The real odd thing is I can create the lines no problem. I tried it 2 different ways shown below. The first way gives me this error..."Object reference not set to an instance of an object.". The second says "Unable to cast COM object.."
Dim oTG As TransientGeometry
oTG = ThisApplication.TransientGeometry
Dim EntityEndPt As SketchPoint
EndPtX = 0 * 2.54
EndPtY = 3 * 2.54
‘Code Fails Here!
EntityStartPt.Geometry.X = EndPtX
I just want to know that how can I get the center point from a Sketch Object ?
View 1 Replies View RelatedHow to place the “midpoint” of window on the midpoint of wall?
In the screenshot below, I wanted to place the window from its midpoint to the midpoint of the wall. How this can be performed on Revit?
The screen shot below shows three coincident constraints and a projection icon on the origin.
looks like a projection icon - what does it mean?
I want to delete the three coincident constraints. But when I delete the coincident constraints there is no Sketch origin center point (the sketch origin center point is a square-yellow dot at the x-y intersection). How to delete or move the three coincident constraints with out deleting the sketch origin center point?
I have this assembly shown in the pic. below. I'm trying to create a point or axis in the blue corner points (to attaches something later on) but it just won't let me choose it for some reason. I know that it's possible to to do that (almost sure I already done this trivial thing in inventor.)
Any reason it's not letting me choose the sketch points/line to in order to create points or axis(s)?
Inventor 2012 Pro.
I7 workstation
I cannot make a plane parallel to a surface and through a sketch point.
I can't also select the sketch point or line in order to make an axis. the sketch point, line from the sketch or anything from a sketch isn't selectable.
how do I retrieve the centre point in my design axis in Inventor, when I create a new sketch, like the point at x0:y0:z0
View 2 Replies View RelatedIt goes f.e. like this:
I draw a line (no constrains) and I can move it by grabing an end or whole line by click&hold mouse button, great.
But after couple minutes of work with part and sketches I can't grab anything. Even on new created sketches and new lines. Click and drag just open rectangle selection. Oh, between these phases there is a phase when 2nd click&hold works...
When I open/create another part it is normall, but this one I must close and open again.
Inventor 2010
Some how I turned off the snap to end point in the sketch mode. where is the dialog box to control snap settings
I would like to use iLogic to find the location of the points of a line, determine if the line is approximately vertical, and apply a vertical constraint if it is vertical.
Here is the code process I envision:
1. Automatically select a straight line.
2. Find the location of its end points.
3. Compare the X-value of the end points to see if they are vertically aligned (or almost so).
4. If they are vertically aligned, apply a vertical constraint.
5. Select next line and repeat.
Is this possible with iLogic? I don't see any way of calling a line's sketch points or finding their location.
I know why you cant loop select and offset the rectangle but surley if you are going to take the time to listen to users and create requested tools, you should do it well?
View 4 Replies View RelatedIn assembly mode, how can I click on two lines in a part sketch and get there intersection point using VBA?
View 3 Replies View RelatedUnfortunately, it's chock full of proprietary customer data, so I can't share the parts or the assembly. But I can pretty well explain what needs to happen, and I've attached a JPG that shows a bit of what I'm doing.
I need to design a bracket to hold an RPM sensor at a certain gap to a spiral bevel gear. I've got a huge assembly model (non-Inventor) from the customer, as well as the model for the sensor. My plan is to start a master IAM, insert the customer assembly, insert the sensor and constrain him, and draw the various hardware I need around the sensor.
So I start by making a work plane that matches the bevel angle and is in a location so the end of my sensor will be flush to that plane. Create a sketch on that plane, then project 2 relevant axes to create the appropriate "origin" from which my location will be based. Place a point on one line, at a certain radial distance and constrain my point.
So now I've got a point and a plane that are where I want my sensing face and my centerline axis to be. What now? I was thinking that I'd create a work axis "normal to plane through a point", but this workflow isn't available in the assembly environment. I can't constrain a solid to a sketch point, so I really don't know what to do at this point in order to put the part where I need it.
I have been searching for a macro to export the start and end point of a line coordinates to excel, but I can only find information on how to export 3D Points.
Is it possible to program a macro that allows me to export the start and end point of various lines in a sketch?
The objective of this is to connect an excel file which is updated when I create a line with it correspondent points, then i could not only import these x,y,z coordinates from excel to inventor but I whould be able to update my spreedsheet whenever I change my sketch.
IV11, IDW.Is there a way to Disable Midpoint snapping while Dimensioning?It seems to get in the way a lot.A lot of the Lines i have to dimension are small and it's Always trying to dimension to the Midpoints of them rather than end points.Not a bad concept.. just in my case it really gets in the way..So just wondering if there is a setting somewhere to turn it off?
View 9 Replies View RelatedI need to define a mate constraint with a workplane as EntityOne and a midpoint from an Edge as EntityTwo.
API-Help tells me valid objects are planar faces, linear edges, vertices, cylindrical faces, conical faces, spherical faces, revolved faces, work planes, work axes, and work points.
The Edge object gives me StartVertex and StopVertex, but what about the midpoint?
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
View 2 Replies View RelatedHow do I duplicate the 2D line work from a part level sketch into a drawing level (overlay) sketch?
I started a simple 2D piping system diagram sketch by opening a new part file and using a sketch to stick draw the system schematic including some annotations. Then I opened a new drawing file and made a base view of the part file to bring a view of the original sketch into the drawing.
I realize now that it would have been much easier to have created the schematic directly in a 2D sketch at the drawing level, which would have made editing the annotations much easier at the drawing level, and there is really no need for the part file to exist. I have no intention of creating a 3D model or "real" part in the .ipt file, was just using it as a jumping off point to sketch.
I was thinking that I could correct my error in judgment by just copying the sketch and pasting it into a new sketch on the drawing, but it doesn't want to work that way. I have tried copying both the whole sketch at the browser level, and the entire sketch contents (all of the lines and annotations) from the opened part sketch, but when I attempt to paste either of those into the drawing, paste does not seem to be an option. I'd rather not have to draw the whole thing again, as in typical fashion, my once simple sketch has grown in proportion and complexity from its simple beginning.
First we imported an ".igs" file to inventor, which produced "wires". Then by promoting the wires it produced a 3-d sketch.
The model is in one plane and 2-D, and we are trying to use Ansys 2-D analysis, but in-order to do so it needs to be in a 2-D sketch.
The model is too large to be redrawn on a 2-D plane, how to convert it to a 2-D sketch
want to change sketch 2013 into the sketch of 2010
View 1 Replies View RelatedWhen I edit certain sketched some other sketches disappear. see attached.
This is causing modelling to slow down as I can not project lines from the sketch that has disappeared.
After I create a adaptive part from projected sketch. How to modify the sketch? Please see the part attached.
View 6 Replies View Relatedwhat is the difference between a sketch and a planar sketch?
View 2 Replies View Related