AutoCAD 2013 :: Leaders Lost Vertices And Detached From Mtext
Jun 27, 2012
While working in a drawing, I noticed that my leaders looked a little odd. They had ALL lost their verticies and upon further investigation I realized that the mtext is no longer attached to the leader (i.e. when you select text and grab the grip and move, the leader, text end, does not follow). Start a new leader command, and all is well with the new leader and text but the old leaders remain disconnected.
This is a new file originated in 2013. Audit was 0. Restarted AutoCad, checked a bak file and auto-save, no changes to mleader settings or attachments. I do no recall executing any out of the ordinary commands or changing settings.
View 2 Replies
ADVERTISEMENT
Sep 27, 2012
I created a dynamic block that contains a quick leader. The problem I have is when I go to my layout views the leader in the block does not show up. If I edit the block, change the layer of the leader and save it then the leader will show up in viewports. Other parts of the block are on the same layer and show up, it is just the leader for some reason.
View 7 Replies
View Related
Feb 26, 2013
Is there a way when creating hatches, for it to ignore annotative leaders? If the line of the leader crosses the area to be hatched, it breaks at the line. But if the arrow crosses the area, it totally freaks out and won't do what it's supposed to (usually inverses what is to be hatched.)
There REALLY needs to be an option to ignore mleader & mtext objects...
View 1 Replies
View Related
Jun 12, 2013
Why does my new lines all show their vertices, even if they arent selected? I dont want the vertices to show when the lines isnt selected.
View 3 Replies
View Related
Sep 3, 2012
When customizing the screen menus, adding a few icons or pull down menus, when autocad is restarted, Autocad reverts back to the default menu. How can I set this up to retain any menu changes I make.
View 2 Replies
View Related
Sep 20, 2013
If I put a single line text and use it several times and then select them all I can change them in the properties all at ones. How do I do that with Mtext, if I select all and go to the properties they are opened one by one and you can change that.
Is there another way to do that as a single line text with the same.
View 9 Replies
View Related
Jul 12, 2012
I have encountered an error in 2013 MEP. Autocad will suddenly not load and it appears that it gets hung up looking for a profile that does not exist. "AutoCAD MEP (US Imperial)" If I am logged in as administrato,r it opens fine. In my own domain, however, it does not. I have repaired, uninstalled and reinstalled to no avail. Incidentally, all of the other Autodesk programs work. Any thoughts on where I can find that profile so that I can redirect to it?
View 1 Replies
View Related
Oct 30, 2013
I am trying to add labels everywhere on my drawing to show the properties of my objects i.e. lines. (But the thing is, I need static text). This is because I need to be able to "distort" the drawing for legibility purposes but retaining the label information. This is a common drafting task in surveying. Solution A - add the labels and then convert then into text. (I don't think Autocad allows this) Solution B - add the mtext via script, but so far I am stuck on the text editor.
Here's what I have done so far. mtext 100,100 <-- I'll need to come up with some calculation to automatically place the text in the middle of the line. j mc r 96d08'27" 130,100 "186° 08' 27""" <-- how to you add the content of the mtext object?
View 7 Replies
View Related
Dec 11, 2013
why when I rotate the mtext to be isometric in this drawing, the multiple lines become offset.
I created the mtext orthagonally like normal and used the rotate command 30 or -30 angles. Is there some other type of isometric rotate or something.
View 1 Replies
View Related
Sep 18, 2013
I am using LT 2013. I cannot figure out how to match properties for text. I click on the 2 options and the box witdth, orientation, layer will match but not the style or font. I have tried using Quick Properties to select but have not had any success with this tool. Here is what I did:
Created a style and named it Arial.
Open the Quickselect box.
Apply to : click the box and select the various mtext objects.
Object Type: mText
Properties: Style
Operator: Select All
Include in New Selection Set is checked.
I click Ok and the objects are selected.
Next I go to the Properties Manager and change the style to the one I want to use, bu the text does not change. If Idoubleclick a text object it shows the correct style, but not the correct font. What have I missed doing?
View 4 Replies
View Related
Aug 22, 2013
I used the CHANGESPACE command today to bring a piece of mtext from model space to paper space. I had a background mask on the mtext and when it came into paper space, the height of the text box displayed right but the width stayed the same as it was in model space. I played around with column settings and also the WYSIWYG in editor settings. Nothing seemed to make difference. What am I missing? Using autocad 2014
View 7 Replies
View Related
Jul 15, 2013
The dialog box for MText is turned off. How do I turn it back on so I can edit text from the editor?
View 9 Replies
View Related
Feb 22, 2013
I have an older drawing that was created by somebody else that is chock full of bad CAD. I have to add some leaders to some text and I'm using the "QLeader" command. For some odd reason when I implement "QLATTACH" it won't attach the leader to the text.
Yes, I could recreate the text with the Qleader command but I'm trying to avoid having to do that because there is a lot of text. I'm not a fan of the rigidness of Mleader either so that is not an option.
View 2 Replies
View Related
Sep 19, 2012
When I create Mtext with a Bullet list, I want to change the bullet to something of my own choosing, instead of the blakc dot. I've been looking into this before, but couldn't find a solution. Some time back, I received a drawing from someone else. See attachment. It contains a piece of Mtext wich uses an alternative bullet, in this case a hyphen. So it CAN be done. Only thing is, I can't figure out HOW they did it?
View 4 Replies
View Related
Sep 28, 2013
I have made a dynamic block with attribute text. Everything works fine except the text comes out as larger than the mtext that it was created from. The text height & the width factor are the same since i created the attribute default by copying the mtext. when i close the block the text appears longer than the mtext it was created from.
View 2 Replies
View Related
Mar 4, 2013
Is there a way to change the defaults?
Presently, the Fill Color defaults to "Red" and I have to check "Use drawing background color" every time. Certainly there must be a way to change this?
While I am at it, how about line space distance? Ditto on default justification, height, etc., etc.?
View 3 Replies
View Related
Nov 10, 2013
Is there a way to create an attribute or MTEXT in a block where part of it is User defined and the other part is constant?
e.g.
"AUTOCAD = 12345 LAYERS"
Where "AUTOCAD =" and "LAYERS" are constant
and
"12345" is the user defined part.
The reason why I would like this is because i want to be able to Middle Center Justify the text and if i were to create 3 separate texts then it wouldn't be good (2 texts and 1 attdef)
View 5 Replies
View Related
Sep 27, 2013
sent drawing out to vendor, received back drawing where they had changed the width factor to .75. is there a way to globally edit all these mtext entities?
View 2 Replies
View Related
Jun 26, 2013
I used "save as" to create a new drawing from an existing file that I did not have any problems with. For some reason, the mtext that already existed shows up in my viewports as well as new leader text, but any new mtext that I've added does not. The viewports were also already existing from the previous file. I have not changed any settings either!
All of the layers are on, and I've tried deleting and re-adding the viewports with no luck. All of the text settings are the same as the original file, and like I mentioned before I did not have any problems with the previous file.
View 3 Replies
View Related
Aug 17, 2012
lets say I marquee select the vertices on a cube in an orthographic view (top view or side view) only the vertices facing the camera get selected. And to clarify, CAMERA BASED SELECTION IS TURNED OFF. Also, not sure if it is related, but backface culling in preferences is also turned off. This usually will not happen in perspective view; but yesterday it did start happening in perspective view as well. And even more strange, it does not affect all meshes in the scene. Only some will react this way.
This bug only recently started happening and it is driving me nuts. I have been running 2013 on this machine since it was released, but not until recently did this bug start to occur; so I am wondering if I accidentally turned something on/off?
View 3 Replies
View Related
Jun 19, 2013
I'm currently using AutoCad 2013 on a Lenovo Thinkpad X230 with windows 7 64 bit. I have 8 gb of ram and a core I7 processor which seem up to the task for the rather small files I create. My issue is that whenever I initiate the mtext command or attempt to edit an mtext object, my cpu usage will jump from about 0 to 4% up to 20 to 30% and will stay at that level until I close the drawing. This causes the fans to run constantly and makes working a little more jumpy. I've tried removing AutoCad completely and reinstlling. I've tried loading up AutoCAd 2014 (and subsequently removing it) and now I'm back to AutoCad 2013 and the problem persists.
I'm assuming it has something to do with the computer or some other software that is running in the background. It's odd that it would only affect this one command. The computer is only 1 month old and I've done the hardware checks that Lenovo offers (no problems indicated).
View 2 Replies
View Related
Jan 15, 2013
I guess it does NOT support it because it seems that it does NOT work properly. For example, in case of multiple lines of “Horizontal” setting, it works properly like followings. But in case of multiple lines of “Vertical” setting, it does NOT work properly like followings.
Configure of “Horizontal”:
ABC
DEF
GHI
Configure of “Vertical”:
ABC DEF GHI
In my perspective, it should go downward like followings.
In my “perspective” of Vertical”:
A
B
C
D
E
F
G
H
I
We are making application software for importing DXF file from AutoCAD. If AutoCAD does not support multiple lines of vertical setting on mtex, our software also should not support it, I think. I want to know the specification for multiple lines of vertical setting of AutoCAD.
View 3 Replies
View Related
May 2, 2012
When i type "qleader" and go to settings and then check the "Always left justify" option under MText Options it will not save. I go open up another drawing and have to do this again. Is there anyway for it to keep the setting?
View 4 Replies
View Related
Oct 10, 2013
Recently installed AutoCAD 2014, and I'm currently trying to type the text:
TC1: 2/90 x 35 MGP10 studs with 4/2.8mm dia nails each end
It keeps stacking the 2/90 into the fraction 2 over 90. How can I turn auto-stacking off? I know I managed to turn it off for AutoCAD 2012, but now I can't find the option or system variable.
View 3 Replies
View Related
Aug 20, 2013
I have a set of notes for a given jurisdiction that I need to show on mumltiple layout tabs within the same file. However, the notes need to change their width, number of columns, height, etc. for each layout tab to work with viewports and other drawing elements within each tab. My question is this- is there way using fields, blocks, rtext, something that will allow me to create one master copy of the note and basically have instances of the note on those other tabs that I can adjust the wrapping, height, columns etc.? I could just create a bunck of copies of the same note, but then if we get a comment from an AHJ about the notes, we need to make sure the comment is addressed in each instance of the note instead of just one master note. Is there way to do what Im asking, or is the technology just not there yet?
View 8 Replies
View Related
Jan 31, 2012
I have multiple singular text objects on my screen and I want to convert them to mtext so I can use the Background Mask option within mtext on my drawing. how to quickly select all the text and convert it to mtext without it combinin ginto 1 mtext?
View 9 Replies
View Related
Apr 16, 2009
Tool to combine multiple pieces of Mtext into a single Mtext with paragraphs?
View 9 Replies
View Related
Apr 8, 2013
I know the difference between attach and overlay for reference files.
The problem here is that the xref IS attacehd as an overlay and I am still not able to detach it.
I am working on WisDOT transportation plans. For those that are not familiar with these projects, certain reference files must plot black in some plan sections, but grey in others. When we submit the plans to the utility companies, all utilities must be black. but are grey in everyother submittal. I changed the xref level attributes to plot black with the intensions of detaching the xref and reattaching to revert back to the orignial grey level attributes. Is there anyway that changing the level attributes is somehow not letting the xref be detached?
Intel Core i5-2500K CPU @ 3.30 GHz
8.00 GB
64-bit
View 1 Replies
View Related
Feb 7, 2013
my 3D geometry going missing after I have saved the drawing. Running AutoCAD 2013, Saving file Format 2010. I draw a room. I have walls, chairs, desks, a floor, etc. I save the drawing. When going to re-open the file I can see all of my geometry in the file preview, but when opening the DWG the floor is missing. All Layers are on and thawed. When running a purge command it indicates that something is on the layer, but I can't see it or select it. Changing visual styles also has no effect. I have used CAD in 3D since CAD 200.
View 9 Replies
View Related
Oct 31, 2012
I'm in AutoCAD 2012. This xref won't go away. I've done the obvious fixes but can't get rid of it.
View 4 Replies
View Related
Mar 26, 2012
Our office recently moved all of our project files to the dropbox. Now when I open files with xrefs I have to attach them back into the file. However, this doesn't happen for my coworker. She can see all the xrefs. How could I solve this? The file names or directory has not changed.
View 2 Replies
View Related
