AutoCAD 2013 :: LAYDEL Command - Delete Unused Layer
Mar 30, 2013
I'm trying to delete a unused layer. But when I do that I get the following error (see attachment). I googled a bit and figured out that the LAYDEL command might solve my issue, but as I'm using Autocad 2013, that's not possible, as it doesn't have this command...
The block that causes the error can also be deleted, I tried with the purge command, but must be doing something wrong cause it didn't work. Oh yeah, with regard to the purge command, I see it this way (attachment 2), how can you display it in a window kind of view to get a better overview?
View 3 Replies
ADVERTISEMENT
Mar 30, 2013
I'm trying to delete a unused layer. But when I do that I get the following error (see attachment). I googled a bit and figured out that the LAYDEL command might solve my issue, but as I'm using Autocad 2013, that's not possible, as it doesn't have this command..
The block that causes the error can also be deleted, I tried with the purge command, but must be doing something wrong cause it didn't work. With regard to the purge command, I see it this way (attachment 2), how can you display it in a window kind of view to get a better overview?
View 4 Replies
View Related
Jan 3, 2012
sometimes i can't delete an unused layer, why? if there's a causal factor, can i ignore and just DELETE it?
View 9 Replies
View Related
Oct 4, 2013
Everyone at the office where I work is having the same problem with AutoCAD 2014:
1. When creating a new layer state, and selecting all layers and clicking "remove from layer state" and then "okay", upon going back into the layer state, about 80% of the layers have returned and you have to select all and delete again and hit okay, and then go back in and do it again, about 7 or 8 times total before the layer state is cleared out and ready for you to add back just the desired layers. Even if you don't create a blank slate layer state to begin with, whatever layers you delete, once you hit okay and go back into the layer state, most of the ones you just deleted are back.
2. Even more of a problem is that sometimes all the already created layer states will suddenly reassimilate ALL layers in the drawing, and the above process has to be done to all existing layer states.
This takes an enormous amount of time to correct for multiple layer states, which we typically have in a drawing.
View 3 Replies
View Related
Jan 14, 2013
I have assymbly wich linked to excel sheet.
I can delete the excel sheet from the assmbly and its parts too, but I can't delete the unused parameters in "List parameters "
And, I can't link a new excel sheet to this assembly, even if I changed the name or made a new one,why?
I use inventor 2012
View 4 Replies
View Related
May 3, 2011
I have an CAD file with a lot blocks which I don't use. I would like to delete them. So I do "Purge" which took care of some but not all. There are still a lot of "cannot purge" blocks. So I do "Insert", I see about 30 blocks. Choosing one of those, I can edit the block. (Doing the "Insert" was just my beginner's test step to see how many unwant blocks I still have.) I believe they cannot be purged because they are nested.
How can I delete the 'cannot be purged" unused blocks?
I know a lot of the blocks have other blocks nested in them. Is deleting the 'parent' blocks enough for me to purge?
View 3 Replies
View Related
Dec 1, 2012
How to purge or delete all unused bitmaps, that collected in bitmap gallery, that no longer is needed, except those, in my page?
View 2 Replies
View Related
Jan 18, 2014
Is there a way to delete an unused keyword tag I created in Elements Organizer 11?
View 1 Replies
View Related
Feb 1, 2012
How does one delete unused or unwanted walls from the properties list?
View 1 Replies
View Related
Nov 19, 2012
instead of isolating the entity selected, it LOCKS all other layers, except the one you select
View 3 Replies
View Related
Dec 13, 2012
I've been using AutoCAD 2013 Korean in Windows XP and Windows 7(32/64bit).
I have a question the command prompt.
The line have the name of layer : 0 (default layer)
I create another layer. It's unicode
And I will change name of layer 0 to 도면층1.
But I can not input unicode character to command prompt.
But It was changed from property dialog.
Can I input unicode character from command prompt?.
Previous version(AutoCAD 2008,2009,2010,2012) CAD worked well.
View 6 Replies
View Related
Dec 23, 2011
I have user parameters that are no longer needed and are not being used anywhere. They each takes 4-5 seconds to delete, prior to 2012 this would happen instantly.
IV2014 SP1 64bit
Dell Precision T7500, Geforce GTX 480, DirectX11 306.97
SpaceExplorer 4.04, 3DxWare 3.12.2
Twin Intel Xeon E5506 2.13GHz, 12GB RAM, Win7 Pro SP1 64bit
View 6 Replies
View Related
Nov 2, 2013
I can delete every unused material except one in the Material Editor.I am trying to make the custom Material library and somehowI have got the Material I cannot delete. URL....
View 9 Replies
View Related
Feb 22, 2013
I have a drawing that has hundreds of text styles that do not seem to be used by anything that I cannot purge. I have even deleted everything in the entire drawing, and it still says that the text styles are in use. Is there a way to override the purge since I know that the text is not in use.
View 9 Replies
View Related
Nov 7, 2012
We've having an office wide problem of drawings getting bogged down with, in some cases, hundreds of linetypes. Not sure where the source of the problem is coming from but as we contiunally use the drawings they keep gaining more and more linetypes, like a snowball rolling down a hill, and the files become so large they are almost unusable. The linetypes don't purge out of the drawing and are not connected to anything. I've tried everything I can think of to clear out the linetypes and the only thing that seems to work is wblocking them. Which when we're talking about hundreds of projects consisting of hundreds of files is a lot of work. We do wblock the drawings in a project on occasion to keep the files usable but they just become infected again eventually.
What might work to clean them up on a batch basis? I've attached a file that's infected so you can take a look. This is a file that has never had anything xref'd into it and was created as a brand new file when originally created. At some point over the last 3 weeks it got infected with the linetype disease.
View 6 Replies
View Related
Nov 21, 2010
I am currently writing a series of routines for setting the layers for text, leaders and dimension commands. The end goal is a system where any annotation command sets the correct layer for the duration of the command, then reverts back to the layer that was active before the command.
I have managed to complete all the code, and it appears to be working fine, I just have one question: I have used -layer "m" "Lay_name" etc... for all layer setting commands, rather than any code to see if the layer exists already. In my limited testing this seems to be suitable, nothing that exists on that layer seems to be affected.
I know how to write code to determine if the layer exists already and set the layer instead, but so far it seems unnecessary??
View 8 Replies
View Related
Jan 4, 2014
After installing the VBA Module, I get the message "Unknown command "VBARUN"". I've rebooted, restarted and tried reinstalling the VBA Module to no avail.
View 4 Replies
View Related
May 15, 2012
I press CTRL+9 to make the Command Line disappear while drawing. When I plot (or when doing a plot preview) , the Command Line appears again by itself. So I always have to turn the Command Line off manually after each plot
The bug still happens;
- if Dynamic Input is turned off or on
- if I plot to a real device or in PDF
- if the Cammand Line Palette i docked or floating.
This is not an issue in AutoCAD 2012 so I guess it has to do with the new way they programmed the revamped Command Line palette in 2013.
Using Windows7
View 2 Replies
View Related
Aug 15, 2013
Why can you no longer delete layers with the delete key?
View 4 Replies
View Related
Jan 31, 2012
At my job, we are 15 drawers using acad 2008 and 2006. For some reson, on 1 computer, when the guy explode a block, acad delete that block insted exploding it. It make the just for some block, not all block. It make this with acad 2006 and acad 2008 but just with that computer.
View 4 Replies
View Related
Nov 10, 2011
I want to know if I have understand this correctly or not: layer previous undos the last change in layer related command. Then If my last action is on layer, unod command will do the same. layer previous advantage is when you want to perform an undo which is not your last action.
View 0 Replies
View Related
May 19, 2012
how to draw a certain line and be able to delete part of it.
Example 1: I would like to draw a bunch of seried resistors, so I made a bunch of rectangles and draw a wire across them. But there are wire crossing through each one of them, how do I remove/erase that part in between each of the resistor? The line is made by using command: LINE
Example 2: Drawing some polygon and random shapes. Simplest example, drawing a half circle, so I draw a circle and want to remove the other half, how do I do it?
Yes, I know in example 1 I can do one object first then copy paste... But that is not what I am asking. I am seeking the command how to remove the lines or object in between.
View 3 Replies
View Related
Aug 1, 2012
It appears that the Layer Filters functionality is broken again with 2013. Unchecking the "Apply layer filter to layer toolbar" disables the function of layer filters in the tool palette.
View 5 Replies
View Related
Jan 17, 2012
Where is the command delete duplicate objects in AC2012? In version 2011 it was in express tools. Whether this command is not in version 2012?
View 2 Replies
View Related
Nov 11, 2012
I'm working on a project that details with topo lines. I have the contours, however because I imported them as DWG's from sketchup they're a bit messy. Basically, instead of being one continuous line, their endpoints intersect and overlap, making it look very messy. Is there anyway I could delete these extra lines? I tried the overkill command to no avail.
View 3 Replies
View Related
May 18, 2013
I cant delete layers named : ceco.net1/ceco.net2/ceco.net3...how can i delete them
View 9 Replies
View Related
Jul 28, 2012
Sometimes in CS6 the delete command just acts as a non-optional "clear" command, and does not show a menu providing the content aware option. Sometimes this cures itself by closing and reopening the program. Sometimes not.
How do I get rid of this defect in the program?
View 1 Replies
View Related
Apr 16, 2012
I am using AutoCAD 2008 and I have a layer that contains no objects which I cannot delete. If I try I am told there are objects on the layer but I cannot find any at all. I have turned off all other layers to try to find the object I need to delete but there is none. How to manage to get rid of the layer.
View 8 Replies
View Related
Sep 7, 2012
I have a layer that contains no objects at all but which I cannot delete. I have tried LAYDEL, QSELETE and other commands which I found by reading other posts with similar problems. Unfortunately nothing appears to be working at all. I am using AutoCAD 2008.
View 9 Replies
View Related
Nov 30, 2012
No Clean button or command in document palette settings.. Of course there are reset command but not to positive results.. I want to delete the colors in document palette but no clean or delete colors command... Also color styles is not useful and very sophisticated.
View 6 Replies
View Related
May 25, 2012
In this particular drawing I have a layer I can see in my Layers Properties Manager but I cannot find in my drawing and it will not let me remove it.
this is a record of what I have just done:
Command: PURGE
Purged *D19.
Purged *D27.
Purged *D32.
Purged _None.
Command: *Cancel*
Command: <Switching to: 3D>
Regenerating layout.
Regenerating model - caching viewports.
[code]....
View 9 Replies
View Related
