I have a drawing xrefing another drawing which has the ecw attached to it - if I change the UCS the ecw disappears.
So the image only shows when the ucs is set to WUCS - I should also note that just the image disappears I can still see the image frame.
When using Autocad 2013, the minimize, maximize, and close buttons on the right side of the title bar frequently disappears. I can make it reappear by selecting the drawing name under the window tab.
View 1 Replies View RelatedThis has been occurring numerous time more than it should. While in a drawing mid command, panning, typing anything pretty much my cad freezes. The rest of my computer is fine everything works properly but CAD is frozen and when i bring my pointer into the program it disappears. I can even open cad up again and the old CAD will stay open. It shows the drawings i have open on the tab bar and i can’t close out of them. I have a computer that’s more than capable to work properly.
View 1 Replies View RelatedI use object grouping for several different things in AutoCAD. With the release of ACAD 2013 I occasionally get the following message upon opening a drawing:
Associative Network Evaluation Error
The object cannot be resolved or value limit has been exceeded.
Inconsistent associative objects my display geometry and grips incorrectly and update in unexpected ways when edited. You can undo to restore the associative object to its previous state.Upon receiving this message, all groups have been removed from the drawing.
All of a sudden my cursor will become invisible. This happens only with AutoCAD. and if I switch between drawing windows it will appear on another drawing file. I have to close the drawing and open it again and then the cursor will be back only to disappear again. The cursor is visible if I move it back to the ribbon or bottom controls. It seems to happen only when it becomes the cross-hair cursor. I can still make selection windows and right click.
Mouse is working fine with all other programs and drivers are up-to-date.
I have a small office and 2 of the associates are using autocad lt 2014 1 is using 2013 and I am using 2007. Up until a few months ago we were all on 2007.
Now when I open drawings from the 2007 version, I cannot see some of the text. I have tried the following: Checking layers to make sure they are onChecking font to make sure they are availabemaking sure annonotation is visiblemaking sure proxy graphics are onMaking a block of just the drawing objects and opening that I am not that familiar with 2014, so I cannot figure out what is happening. Note - when i look at the drawing in the preview window, I can see the text. But when I open it, it is not there. If I save in 2014, the text no longer shows up in the preview.
In 2013, when I place a balloon, or drag an existing one around, the text inside the balloon either disappears or gets mundged. My hardware setting is on "Performance". I tried it on "Compatability" as well with the same results.
[URl]
Graphics card supports both DX10/OpenGL. Worked fine for 2011 and 2012.
Upon selecting anything in 90% of any drawings the crosshairs disappear and CAD2014 freezes for 2sec.
It's a Dell Presicion T1600, Xeon 3.4Ghz, 16GB RAM, Quadro2000 with a 120GB SSD as the primary running CAD2014 premium.
It started recently.
This happens even if I toggle HW acceleration. We draft mainly in model view with the 2D Wireframe style.
I have a library of blocks that I built for our company to use. We recently upgraded from 2013 to 2014 and boy did it throw our library for a loop!
There is a check box (reflectivity) that leaves the materials black when the drawing shade mode is changed to Realistic (unless you go in and uncheck the reflectivity box) and while I have figured out how to alleviate that issue (by unchecking it on our tempate and saving it) I am still having a materials issue with our blocks.
I can open the block (and turn on Realistic mode) and all the pieces have their materials like they should. I then open a new drawing and insert the same block into the drawing .. one piece is sans material.
I cannot for the life of me figure out why it's there on one drawing but it gone when inserted. The new drawing has been purged and doens't contain anything it shouldn't.
[URL]
As you can see when I drag the appearance swatch to apply it to the text. The text disappears and only comes back when I change color.
View 2 Replies View Relatedwhen I try to change the font in corel draw x4, the text disappears, this happens with new documents, old documents etc.
It works in Photo Paint, but for some reason draw has stopped working. I restarted and tried everything I could think of!!! This seemed to happen after the latest windows 7 update.
Also on a sidenote is it possible to get rid of the ads when i start up Draw and PP x4? It keeps hassling me to upgrade. It is really really annoying... seriously I bought this product, why does it have pop up ads???
I am using PSE12 with Mac OS X Mavericks. If I use the type tool, type some text then want to change maybe the font or size, the text disappears! If I set the parameters before typing everything is OK, but it is really inconvenient.
Also when I do a return in text the first letter of the next line is always a capital whether or not I start a new sentence!
I didn't notice when and why it happened, but now when i draw white line, it appears brown. I didnt change any settings, just did my usual work, when it appears. Other colors are normal. What could it be?
View 6 Replies View RelatedAutocad 2014
One of our company standard template has preloaded dim styles.
I wish to change all of them so that the text is closer to the baseline.
How do I amend all of them in one go.
I always imagined they were all based on the standard one and if I changed the standard they would all reflect these changes.
If I put a single line text and use it several times and then select them all I can change them in the properties all at ones. How do I do that with Mtext, if I select all and go to the properties they are opened one by one and you can change that.
Is there another way to do that as a single line text with the same.
How to change the koordinates in a 3D dwg to 2D?
View 9 Replies View RelatedHow is possible to change the name the block? I tried to do that through the properties window and it was not possible.
View 2 Replies View RelatedI pulled in a survey from an outside vendor and was just going to work with what they have. Their MLEADERS are a different font than what I would like and changing the Text Style doesn't work. I notice in the properties for the MLEADERS that the contents don't have just the mleader text, but is says this instead:
{fSansSerif|b0|i0|c2|p2;W1;TEXTHERE}
Obviously its overriding with the text style with the bit of code. But is there a way to change it? Hitting the ellipses in the Contents properties just transfers control to the model space. I can't edit from the properties panel like you can with a DIM or anything. I don't remember how it functioned in '08 or '12. MATCHPROP also does not change the font.
Yes I could just create the MLEADERS but I feel it would take less time delete that fSansSerif junk than it would be to place and retype every single MLEADER in the drawing.
I have a drawing that was drawn in 3D CAD and I need to convert to 2D CAD. I changed the view, but I cannot remember what the command is I need to type in to change to 2D.
View 3 Replies View RelatedI know that when I select a group of objects and then list them, the list displays the properties in the order I drew them, is there any option I can change this order? I mean, for example the direction I select them or something like that.
View 1 Replies View RelatedWhen I export text using data extraction, I make another table xls. Can I change text in the XLS file, and then update the text in my drawing to match the new text in the XLS file?
View 2 Replies View RelatedI am looking for a way to change the toggle polar On/Off from F10 to F6. I already did it with the "delete" and the "Ortho" keys but i can't find the macro for the toggle polar on/off.
Has you can see on the picture for Delete it's ^C^C erase;
For ortho it's ^O
Maybe for Polar it's ^P but i could validate with you before i do any changes. (;
How do you change the limits of a drawing in AutoCAD 2013? I have specified the limits for the bottom left and top right, yet it still isn't working. Is there something that I am forgetting or not doing right?
View 1 Replies View RelatedIn a sketch block how do you change the line weight..i tried through Block Editor but cannot change...lineweight is currently 0.25mm but i want to change to .70mm..
View 2 Replies View RelatedI trying to change dimensions but they will not change.I add a block and then try to dimension it against another block but when i go to change the dimension it just remains the original dimension size. E.g. it currently is 2.895 and i go to make it 3.00 but it does not accept the new dimensions....is there a setting i could check?
View 3 Replies View RelatedWe have a drawing with 100 tabs,
How can we change the printer on all tabs at one time. Example: All tabs are now for printer 78 but we need them to print on printer 77.
This was working in 2010 but does not work in 2014.
routing attached.
Can I insert a field in the title block in the layouts that will show the date of the last change made to the part of the model that is shown in the layout view.
View 2 Replies View Relatedhow can I change the scale of a dwg from AutoCAD 2013 version on 1'=1/4" into 1'=1/8" AutoCAD 2006?
View 4 Replies View RelatedI have a problem between my template in inch and the one in mm.
Its the linetype scale that is wrong in the mm one, when i draw in the inch one, everything is fine but when i draw in the mm one, i have to set the ltscale to like 25 to see them at the same scale that they are in the inch one.
My guest is its because i've create my template for the mm one base on the inch one and i just change the unit type to mm. Is there a setting i could change that will arrange this?
Product Design Suite 2013
Currently when ever I render an image using Inventor 2013 the reflection shows a parking lot. It doesnt seem like it matters what type of material I choose or the color that I choose. I have found some older fixes that date back to 2008 but nothing for 2013.This link is the only thing that I can find and as I said it is for 2008.
[URL]
We went in to the registry and tried following the steps but some of the working is different and didnt want to mess things up.
I write plug-in for AutoCAD in C# and I have a question. How I can change dws-file in active document?
I know how it's doing in LISP, but not in C#.