Upon setting up a drawing for plotting (the problem is not printer specific) the "Print Preview" gets stuck in a loop where I am unable to exit if I choose to cancel or alter the settings. I am forced to go ahead and send the plot. If iI immediately go back and run the PLOT command again nothing happens... no dialog box, no error nothing. I must then go to any other open dwg, do a save, and then go back to the original dwg. Then the PLOT command will again work, however, still getting stuck in the preview loop.
When plotting and doing a 'plot preview' Acad crashes. This happens with ALL dwgs no matter which of our 2 printers is chosen. This is only happening to one computer in the office. All computers are running Windows 7 Professional with AutoCAD Civil 3d 2011. If the plot is sent without a preview everything if fine with no crash.
Excuse my awkwardness but I'm self taught on AutoCAD & have managed fine for last few months but have encountered an issue this evening I can't resolve. I've produced drawings, basic they may be, but when preview them the actual drawing area is barely noticable & when export to pdf it practically prints a blank page. I have very simple items in drawing, stockpiles, excavations test locations, and have been producing pdf's fine, even as recently as this morning using the same cadfile. But what ever I've managed to do since then has changed something and I can't resolve the issue.
For some reason, my plot style is applied to my viewports. So for example, when I choose a monochrome plot style for the layout, the view ports in that layout display in black and white. I want to disable this. Is there a system command to turn this off?
I have a stationing line. I've used the block PTTICL to make ticks. The ticks display perfectly. I'll run through a plot preview and the ticks show on the plot preview. I push plot go to the printer and the ticks are not plotted.
I've checked the layer. They are on a layer that should print.
I've checked the block. The block is created on a layer that should print.
I've run through a number of options regarding the alignment label properties and found "display" to be equal to "true."
Everything else plots just fine. Only the station label ticks refuse to plot. My project is fairly short so the work around was to put a poly line right on top of the tick mark.
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
When I trying to plott (or do a preview) with HP LaserJet 1525 nw configurated, autocad crashes. I have the latest drivers and updates installed Autocad 2011 64bits (sp2) on windows 7 64 sp1
I have a coworker who is having trouble printing from AutoCAD 2011 (sp2) on his Dell Latitude, Win 7 64 box. Whenever we try to print or even do a print preview, it will crash the program
He has tried several printers and uninstalled and reinstall the drivers for them. Tried uninstalling and reinstalling the program as well.the Windows Application event viewer shows this when AutoCAD crashes.
Also, I have trouble remoting into his laptop because it will not display correctly with our Landesk software. So I'm wondering if this is a display problem rather than a printing problem.
When attempting to print drawings that have been printed before...much of my drawing will print but many lines and blocks will not show up in preview, or print. i wonder whatt he problem is, as there are some lines which have exactly the same properties (ie on the same layer with no overides etc). where some will print but others wont (ie on the same layer etc). A similar problem persists where some xrefs show in preview and others don't.
Also the stuff in layout space is part there and part not, where this layout title block etc is standard for all drawings and has always printed fine.
It seems the only way to solve it is to copy everything into new drawings (including xrefs) and start again....? I have checked layers, no print etc...
I am trying to create a closed loop alignment for a track. Previously i have included a small gap between two alignments to get around the problem when a housing plot is created (see the attached dicument) when a closed alignment is created, Is there any way of getting rid of this?
I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
AutoCAD - Why does the Normal plot style plot in color? Black seems to make a lot more sense. Almost everyone in Architecture uses black prints most frequently so that should be the default. And you can't adjust Normal to all black. So what was AutoDesk's reasoning?
I know we can do this easily in AutoCAD Electrical, but I could not find any command or feature in AutoCAD to set up this function so that when two lines are intersected, the cross point will become a dot or loop.
But I can't apply it because the site states my account has not been activated. It places me into a loop to resend to my email to activate my account. I'm in a never ending loop. There seems to be a glitch to the site.
When I am in paper space I sometimes double click in my viewport. Then the viewport becomes my whole window. How do I get out of the viewport without doing an undo until I reach where I first began?
Also sometimes when I double click in the viewport, but the viewport is the only thing visible in the screen, (vs having the whole sheet and being able to click out) I don't know how to get out without Undo.
While publishing several drawings I am having problems creating Single Sheets, (a customer preference). Even though I have the Multi-sheet/Single-sheet setting set to "Single" Autocad still creates a multi-sheet PDF. I am using Autocad 2012.
When I switch tabs in my UI (I use Drafting and Annotation), they bug somehow and they don't upgrade visually. What I mean is that if I switch "Home" tab to "Annotate", it keeps showing "Home" tab maximized, but the if I click "Line" it would use "Multiline tool", as they occupy same space in corresponding tab. I can fix it temporarily by multi-clicking bar, but after next switch between tabs, it would bug again. I assume it is not hardware problem, as it used to work for me, then I reinstalled my OS and bug started.
I used refedit to freeze a couple of items that were nested. My drawing file/machine locked up when I attemped to freeze them. I had to reboot, when I opened the file again I was still stuck in refedit mode. I cannot use refclose to get out our that command. It wants me to use refedit again. I need to get back to my work.
I was attempting to hatch a simple closed polyline when all of sudden AutoCad had to pull a stunt and give me the FATAL ERROR shut down. When I recovered my drawing, it automatically launched the hatch creation window..just as i left it. However, nothing works. I can't hatch anything, and I can't close the hatch editor ribbon. If i try to select an area to hatch, it lets me select it, but then glitches out and asks me for a base point to move something. I've tried everything, DPLGMODE set to 1, save as, close, shut down, etc..
I have a user that can't move or resize his xref dialog box. He is using dual monitors and has no problem with any other dialog box. I've tried changing settings for docking/hide.
I'm having a plotting issue with one of my drawings. It's not showing up on plot preview, or even when I print it.
Any other drawing I create under the same Page Setup print fine. The paper and viewport have been have been set up for a standard 8x11, and drawing appears in as normal in the viewport. The layers are ok with no attributes (i.e transparency) set as to affect the print output. The printer drivers are up to date, and really doesnt make sense as any drawings I create under the exact settings show up normally and print out with no problem. Really don't want to recreate the drawing from scratch.
I have a site drawing which has a decently high resolution satellite image underneath. When I try to plot to a pdf, the underlying satellite image doesn't show up. In the plot-preview mode it does show up, but not in the actual pdf created.
I've created a simple drawing in CAD that contains a cropped JPEG, a two toned hatched polygon in behind it two MTexts overlaying all.
I cannot view them in either normal plotting, pdf format, jpeg format and even dwf.
I've increased the ram used in the "Raster Extension Options" (2000 MB), I've set the plotting in the "Process Document" to "...In computer", I've saved it in older formats (2000/2004/2007), I've placed the drawing on both our public drives as well as the local, I've adjusted the "Raster and Shaded/Rendered Viewports" & "OLE" settings in the "Device and Document Settings" (None to Best). Not to mention the other variations in the plot menu.
I've tried everything I can think of and have read through several threads here and nothing works.
What drives me nuts about this, is that I'm able to print from a layout with no problems a 3D drawing, with 2D hatching, an extensive title block with hatching and a secondary overall viewport (minimal detail) in the main viewport area.
I'm running Autocad Architecture 2013. My .dwg has about 15 pdf's in it (from a consultant that does hand drawings that I scan in, and use the image manager to insert into my drawing). The PDF's range from under 1mb, to 10mb. The PDFs are in model space and within my various drawing sheets, I show them in my drawing sheets via multiple viewports. I noticed that when I go to plot a sheet that has pdfs shown in viewports, and click on PLOT PREVIEW, the PDF's don't show up - everything else shows up, linework, jpegs, etc, but not the PDF's! I fiddled with the viewports and noticed that if some part of the PDF's image frame was visible in the Viewport, the PDF would appear in Print Preview. But if the viewport sat directly over the PDF's image frame, the PDF would not show up in the Plot Preview!!!
Could it be I've exceeded the maximum number of Viewports in my entire .dwg? (I have about 16 sheets), Or, could it be some mysterious autocad system variable that I'm running up against.
