AutoCAD Map 3D :: Print Preview And Plot Doesn't Work
Sep 27, 2011
I'm using AutoCAD Map 3D 2009.
I've created a simple drawing in CAD that contains a cropped JPEG, a two toned hatched polygon in behind it two MTexts overlaying all.
I cannot view them in either normal plotting, pdf format, jpeg format and even dwf.
I've increased the ram used in the "Raster Extension Options" (2000 MB), I've set the plotting in the "Process Document" to "...In computer", I've saved it in older formats (2000/2004/2007), I've placed the drawing on both our public drives as well as the local, I've adjusted the "Raster and Shaded/Rendered Viewports" & "OLE" settings in the "Device and Document Settings" (None to Best). Not to mention the other variations in the plot menu.
I've tried everything I can think of and have read through several threads here and nothing works.
What drives me nuts about this, is that I'm able to print from a layout with no problems a 3D drawing, with 2D hatching, an extensive title block with hatching and a secondary overall viewport (minimal detail) in the main viewport area.
View 6 Replies
ADVERTISEMENT
Nov 21, 2013
I have C3D 2010, 2011, and 2013 installed on my pc. I use the Publish command almost daily, and haven't had any serious issues with it when using 2010 or 2011. But in 2013, when I publish it just sits on the same screen and never actually publishes. I have tried turning off Publish in Background, I have checked that the printer support paths are the same as in 2010 and 2011, and I have tried Publish with different Page Setups.
View 3 Replies
View Related
Jan 20, 2012
I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
View 3 Replies
View Related
Sep 1, 2011
AutoCAD Architecture 2011
Windows 7 x64
8GB RAM
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
Using the non-AutoCAD driver works.
View 1 Replies
View Related
Aug 29, 2011
When I trying to plott (or do a preview) with HP LaserJet 1525 nw configurated, autocad crashes. I have the latest drivers and updates installed Autocad 2011 64bits (sp2) on windows 7 64 sp1
View 1 Replies
View Related
Aug 17, 2011
I have a coworker who is having trouble printing from AutoCAD 2011 (sp2) on his Dell Latitude, Win 7 64 box. Whenever we try to print or even do a print preview, it will crash the program
He has tried several printers and uninstalled and reinstall the drivers for them. Tried uninstalling and reinstalling the program as well.the Windows Application event viewer shows this when AutoCAD crashes.
Faulting application name: acad.exe, version: 24.1.208.0, time stamp: 0x4dbf9c16
Faulting module name: ntdll.dll, version: 6.1.7600.16695, time stamp: 0x4cc7b325
Exception 0xc0000374
Fault offset: 0x00000000000c6ab2
Faulting process id: 0x28c
Faulting application start time: 0x01cc5c6016a04e15
Faulting application path: C:Program FilesAutoCAD 2011acad.exe
Faulting module path: C:WindowsSYSTEM32
tdll.dll
Report Id: dcb31b1a-c853-11e0-a254-463500000031
Also, I have trouble remoting into his laptop because it will not display correctly with our Landesk software. So I'm wondering if this is a display problem rather than a printing problem.
View 8 Replies
View Related
Oct 1, 2009
When attempting to print drawings that have been printed before...much of my drawing will print but many lines and blocks will not show up in preview, or print. i wonder whatt he problem is, as there are some lines which have exactly the same properties (ie on the same layer with no overides etc). where some will print but others wont (ie on the same layer etc). A similar problem persists where some xrefs show in preview and others don't.
Also the stuff in layout space is part there and part not, where this layout title block etc is standard for all drawings and has always printed fine.
It seems the only way to solve it is to copy everything into new drawings (including xrefs) and start again....? I have checked layers, no print etc...
View 3 Replies
View Related
Aug 29, 2013
I am a Mac user and new to AutoCAD. I am enrolled in a CAD class this semester and the instructor for my session is requiring Windows. Supposedly this is because AutoCAD for Mac does not allow for proper printing on their plot style setting.
I understand that I can install Bootcamp and Windows on my computer, but I'd really like to avoid that if I can. If I were to do my work on my Mac and then digitally transfer my files to a PC for printing purposes, would my files become corrupted or compromised in any way?
View 2 Replies
View Related
Jan 8, 2014
I received an Autocad file from another person, opened it with Autocad 2011 LT, and it looks fine. But when I go to print preview all the lines are very thick, making the detail of the drawing difficult to see. I've tried manually changing the lineweights but it has no effect on some of the layers. Is there an easier way to fix this other than recreating layers?
View 1 Replies
View Related
Jan 22, 2013
I have a drawing that I created with acad 2010 that has a pdf xref attached. I just updated to 2013. And now when I go to plot the drawing my xref shows up in preview but doesn't show up on the plot.
I can go back to my 2010 version, and it plots fine. What gives?
View 0 Replies
View Related
Jan 16, 2009
So I am working on this document and it has silver background. I go to print preview (Photoshop cs3 and cs4 on Vista) and I get color looking more like bronze looking but when I do print, it comes out just like it should (in working mode which is Monitor RGB with Proof colors checked).
This setting is the only one I've used to make sure image/psd looks exactly like what it should when printing. I tried the default Working CMYK with and without Proof colors but it's still showing me the bronze look instead of silver. I've looked on the net and no exact easy fix for this was found. I really really appreciate any help.
Another simple question is regarding size. I'm working on a document size of 17.5 x 8.7 inches and the actual Banners will be printed at size 175 x 87 inches (5 banners each at 35inch wide but combined into a big one). So essentially, I'm working at 10% the size of what the final print will be and my file size is 760mgs. You can only imagine how big the file would be if I work on the actual size.
View 4 Replies
View Related
Apr 8, 2013
Using ACAD 2008, I am having an odd problem where when I print preview/plot this drawing with a viewport the result is a blank page but when I remove the viewport it plots fine.
View 0 Replies
View Related
Oct 18, 2012
When I try to plot my drawing, my drawing only takes up 2/3 of the page on print preview. The top half of the page is blank. How can I make my drawing take up the whole available page?
View 9 Replies
View Related
Sep 20, 2013
Have a dwg with two layouts sheets that print to pdf in paper space - one layout works just fine the other NOT.
Both include one view port and a few small details as pdf underlays(@ 150 kb each) in the PAPER space layout.
The problem sheet - ran a very slow plot preview but it did complete a full view of the layout, then when selected to do the plot it never completes the pdf.
I tried a pdf plot of the same area in MODEL space and it previews just fine and plots to a pdf just fine.
View 7 Replies
View Related
Nov 28, 2012
I am facing this problem that when i give plot command and preview the window it show fonts different other than my main window. Also it prints as per the preview window and not as per the fonts present in my AutoCAD model space and layout.
View 1 Replies
View Related
Jul 12, 2013
I have a sheet that has several alignments data referenced and labels applied. Recently some of the alignments changed (slightly extended), I checked the sheet and all of the labels have auto updated. Everything looks good. A Print Preview looks good.
When create the print (to pdf), the alignments that changed and all the labels do not show up. Nothing changed with layers, styles, etc. I tried Synchronize and Refresh from Prospector. I can create another Data Ref but don't want to go thru all the labeling again.
Preview and pdf attached.
C3D 2012
C3D 2012 sp1
W7Pro 64bit
HP Z400 Workstation
16 GB RAM
Intel Xeon CPU W3565@3.20GHz
NVIDIA Quadro 4000
View 2 Replies
View Related
Nov 1, 2012
I have a problem with previewing effects in Illustrator. When I do this:
- create or select object
- go to appearance panel
- choose FX -> Stylize -> Drop shadow...
- check Preview in the effects window (it works as expected)
- now uncheck the Preview checkbox (when unchecked, the fx is still visible)
So, unchecking this Preview checkbox doesn't work right. It is very annoying. It is broken for most of the effect in illustrator. Strangly, it works fine with rounded corners effect. But other effects... not.
View 6 Replies
View Related
Jul 8, 2013
Here's the screen shot. If I ignore the preview, and set with the print area tool, I get what's in the print area tool. Something is amiss in the land of tiling settings, but I can't get to whatever setting is messing this up.
View 1 Replies
View Related
Jun 18, 2013
This is a serious workflow disruption: In CSx I could open any file, choose a print preset, click on 'custom' for Media Size and it would automatically adjust the print width and height to whatever the artwork boundaries were (Ignore Artboards ✓'d). Now in CC it just uses whatever I had set for the print preset when I created it rather than adjusting like bfore. Is there something I'm overlooking? Can/will this be fixed? This might sound like small pease compared to the overall view, but this makes a design that would normally take a few seconds to print to our screens to almost half a minute.
View 2 Replies
View Related
May 21, 2013
I have one drawing per file at model tab. When I need to plot a multiple page file, I use:
Print > Batch Plot.
The problem is that I have to set plot configurations ( plot style table, plot area, paper size, etc) in each file before use Batch Plot.
Now I received 722 files with a wrong Plot Style Table. For this time I change the associated *.ctb file at Plot Style folder, but I will need to associate the right *.ctb to each drawing. It's also common to have to change other properties.
View 1 Replies
View Related
Jun 8, 2012
in print module main window for image control (not preview window in the left upper corner) is blank. what is the reason and how can be remedied? os Mac Lion 10.7.3 lightroom 4 ( the 3-rd version had the same problem)
View 8 Replies
View Related
Nov 29, 2012
I have a stationing line. I've used the block PTTICL to make ticks. The ticks display perfectly. I'll run through a plot preview and the ticks show on the plot preview. I push plot go to the printer and the ticks are not plotted.
I've checked the layer. They are on a layer that should print.
I've checked the block. The block is created on a layer that should print.
I've run through a number of options regarding the alignment label properties and found "display" to be equal to "true."
Everything else plots just fine. Only the station label ticks refuse to plot. My project is fairly short so the work around was to put a poly line right on top of the tick mark.
AutoCAD Civil 3D 2013.
View 5 Replies
View Related
Aug 21, 2012
Can users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?
View 1 Replies
View Related
Aug 29, 2011
When I publish a drawing as a multipage DWFx (or PDF for that matter) with "Include Layer Information" selected, the Plot Stamp (Simple Date/Time and Text) comes out but on different layers on different layouts.
Example:
First Layout : Plotstamp resides on Layer 0
Second Layout: Plotstamp resides on Layer 3P
Third Layout: EQPT-VC
etc
Some general information:
Autodesk AutoCAD 2011 64bit
Autodesk DesignReview - 2012
Adobe Acrobat X Professional
Layer 0 Is thawed/plotable and on in all layouts, viewports all layers, viewports. It has at least one entity per layout
Is there anyway to rectify this and still use the built-in Plot Stamp?
View 2 Replies
View Related
Jan 17, 2012
So the firm I work at has AutoCAD 2000 and 2007. 2000 is installed on 5 out of the 7 computers, and 2007 installed on 6 of the 7 computers. 2 of the computers running just ACAD 2007 are Windows Vista, while all the other computers are Windows XP. We have an OCE TDS320 CAD Printer, an HP Wide Format Printer and a Panasonic 330 Copier/Fax/Printer. Our Problem is that When you try to plot an ACAD2007 drawing it will only plot it in color. This problem did not exist before 1/12/12.
When I select the Plot Style to print I select "monochrome.stb" which has always worked, now all of a sudden it doesnt. The only way i have found to fix this problem is to change my drawing to layer "0" which is white, so when it tries to print in color it will print black. Another Guy in the firm i work at has ACAD2007 on his computer running XP, he also has 2000 running on the same computer. When he tries to plot on ACAD2007 the same thing happens, so it is not isolated to my computer.
There is a difference though between his Plot Styles on his computer and the ones on mine. His end with .ctb, which works. It only doesnt work when he tries to print a drawing i made off of my computer. Because of this we copied his Plot Style folder for AutoCAD 2007 and installed it into the folder with all of my plot styles on my computer, replacing the ".stb" with ".ctb" That did not work at all. The last thing we tried was to copy over a file that plotted correctly, delete the drawing and draw what we needed, This also did not work. So basically we are thinking that ACAD2007 is not reading the Plot Styles correctly, or the Plot Styles are wrong or currupt.
View 1 Replies
View Related
Jan 17, 2013
I have several objects on various layers in model space and they are exposed through a viewport in a paperspace layout. I also have a corporate CTB plot style.
Here is my problem: If i plot the objects from model space, they all plot with the correct lineweights as defined in our corporate CTB, but when i plot them from the paperspace layout, some but not all objects plot with a heavier lineweight than what is defined in the CTB.
I thought the CTB was supposed to override any settings applied to individual objects, but more importantly, why the different results, on the same objects, depending upon the space from which they're plotted?
View 3 Replies
View Related
Aug 13, 2012
I have found that when I Publish, the drawing comes out shifted about 1/8" down and 1/8" left as compared to when I use Plot. Which of course is just enough to cut off the sheet border which is 1/2" from the paper edge. I am using the same Page Setup for both Publish and Plot, same drawing.
This is to an Oce TDS600, and it only happens with 15x21 paper size. All paper sizes are set to 0" border. Probably an Oce issue, but have any of you seen this before?
View 1 Replies
View Related
Aug 8, 2012
I recently upgraded from 2010 to 2012 and when trying to plot, using the very same page setups as before the upgrade, the quality (or resolution) of the plot is very poor and pixelated. I am using very high resolution aerial imagery. The output is not at all high resolution (totally pixelated, not presentable as professional). It seems like AutoCAD is reducing the image quality now. Is this a system variable that can be adjusted?
View 1 Replies
View Related
Jun 25, 2013
In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to "None".
The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.
I tried to add this plotter through "Add-A-Plotter Wizard", but each time I obtain an error massage "Autodesk Hardcopy component failed..."
[URL]
View 2 Replies
View Related
May 9, 2011
Unfortunately I am using ACAD 2000 so bear with me and the only ACAD training I have is a 3 day crash course at the local software reseller.
I am attempting to plot a drawing that was created from a template into a .pdf but it is plotting colored lines instead of black lines.
Here is some background info. My template is set up as a .dwt which I will save as a .dwg when I begin to make my drawings. Plot style table is “monochrome.stb” and I have selected Adobe .pdf as my plotter configuration. I then select the “Properties” then go to “Custom Properties”, “Paper/Quality” tab and then select “Black & White” as my color.
When I go to plot the drawing as a pdf and do a preview of what I am about to plot, I see that the lines that make up the drawing are a shade of gray in color. All my lineweights in the layers property manager are set to default. I have attached a blank drawing that is based off of my template.
View 1 Replies
View Related
Aug 14, 2012
2004 and how to turn "plot to file" off? Any time they go to plot the plot to file is already set and grayed out. It has been way too long since 2004 and I don't know where to have them look although I assume it is in Options somewhere.
View 2 Replies
View Related
