I have a site drawing which has a decently high resolution satellite image underneath. When I try to plot to a pdf, the underlying satellite image doesn't show up. In the plot-preview mode it does show up, but not in the actual pdf created.
View 5 RepliesI am facing this problem that when i give plot command and preview the window it show fonts different other than my main window. Also it prints as per the preview window and not as per the fonts present in my AutoCAD model space and layout.
View 1 Replies View RelatedI have a stationing line. I've used the block PTTICL to make ticks. The ticks display perfectly. I'll run through a plot preview and the ticks show on the plot preview. I push plot go to the printer and the ticks are not plotted.
I've checked the layer. They are on a layer that should print.
I've checked the block. The block is created on a layer that should print.
I've run through a number of options regarding the alignment label properties and found "display" to be equal to "true."
Everything else plots just fine. Only the station label ticks refuse to plot. My project is fairly short so the work around was to put a poly line right on top of the tick mark.
AutoCAD Civil 3D 2013.
AutoCAD Architecture 2011
Windows 7 x64
8GB RAM
Created new PC3 for KIP 3100 plotter using its AutoCAD Heidi driver for Win7x64. Upon plot preview the following error occurs.
This causes a crash report which has been submitted to Autodesk. The response was to install service pack 2. Error still occurs after installing the service pack.
Using the non-AutoCAD driver works.
When I trying to plott (or do a preview) with HP LaserJet 1525 nw configurated, autocad crashes. I have the latest drivers and updates installed Autocad 2011 64bits (sp2) on windows 7 64 sp1
View 1 Replies View RelatedI have a coworker who is having trouble printing from AutoCAD 2011 (sp2) on his Dell Latitude, Win 7 64 box. Whenever we try to print or even do a print preview, it will crash the program
He has tried several printers and uninstalled and reinstall the drivers for them. Tried uninstalling and reinstalling the program as well.the Windows Application event viewer shows this when AutoCAD crashes.
Faulting application name: acad.exe, version: 24.1.208.0, time stamp: 0x4dbf9c16
Faulting module name: ntdll.dll, version: 6.1.7600.16695, time stamp: 0x4cc7b325
Exception 0xc0000374
Fault offset: 0x00000000000c6ab2
Faulting process id: 0x28c
Faulting application start time: 0x01cc5c6016a04e15
Faulting application path: C:Program FilesAutoCAD 2011acad.exe
Faulting module path: C:WindowsSYSTEM32
tdll.dll
Report Id: dcb31b1a-c853-11e0-a254-463500000031
Also, I have trouble remoting into his laptop because it will not display correctly with our Landesk software. So I'm wondering if this is a display problem rather than a printing problem.
When attempting to print drawings that have been printed before...much of my drawing will print but many lines and blocks will not show up in preview, or print. i wonder whatt he problem is, as there are some lines which have exactly the same properties (ie on the same layer with no overides etc). where some will print but others wont (ie on the same layer etc). A similar problem persists where some xrefs show in preview and others don't.
Also the stuff in layout space is part there and part not, where this layout title block etc is standard for all drawings and has always printed fine.
It seems the only way to solve it is to copy everything into new drawings (including xrefs) and start again....? I have checked layers, no print etc...
I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
View 3 Replies View Related“annotation scale” on the lay out mode,
I’m not sure about the current “annotation scale” in case of lay out mode.
Annotation scale option is displayed only in the model and viewport mode but not in the lay out mode (attached)!
Based on what annotative objects living on the lay out but neither in the model (or viewport) are re-sized? At this mode, there is no option to choose the annotation scale?
On other words, how to choose the annotation scale in the lay out mode?
Just downloaded LR 5 and noticed that I cannot jump back from a Publish Service folder preview to a different folder preview in grid mode. The only way to view photos in another folder is to restart LR 5. This only happens when I am viewing photos in a Publish Service such as Flickr.
I updated from LR 4 using Creative Cloud installer.
I have just switched over to 2014 and i cannot for the life of me get my batch plot to plot PDF's to a single file! Instead, it's printing all 37 layouts separate. I tried switching between multi-file & single file in the publish options, but nothing!
i know that it took me a while to perfect my settings the last time i set up a new version, but i am struggling to work it out now.
How can I query autocad map data in preview mode,and store these objects in a collection by using C#.
(I want to use simple query like all lwpolyline having layer = "test" and color = 3). If I run this query in draw mode multiple times what will happen? (means possibilty of duplicate objects??)
I'm having a plotting issue with one of my drawings. It's not showing up on plot preview, or even when I print it.
Any other drawing I create under the same Page Setup print fine. The paper and viewport have been have been set up for a standard 8x11, and drawing appears in as normal in the viewport. The layers are ok with no attributes (i.e transparency) set as to affect the print output. The printer drivers are up to date, and really doesnt make sense as any drawings I create under the exact settings show up normally and print out with no problem. Really don't want to recreate the drawing from scratch.
Every time I try to print or preview the following error appears and no error code or log comes after.
I already instaled SP1, changed acad.ctb e use other templates.
When plotting and doing a 'plot preview' Acad crashes. This happens with ALL dwgs no matter which of our 2 printers is chosen. This is only happening to one computer in the office. All computers are running Windows 7 Professional with AutoCAD Civil 3d 2011. If the plot is sent without a preview everything if fine with no crash.
View 4 Replies View Relatedin ps my text looks fine,. but when i go to preview for plotting its rotated 90 deg.
View 1 Replies View RelatedAutoCAD 2010 SP2:
Upon setting up a drawing for plotting (the problem is not printer specific) the "Print Preview" gets stuck in a loop where I am unable to exit if I choose to cancel or alter the settings. I am forced to go ahead and send the plot. If iI immediately go back and run the PLOT command again nothing happens... no dialog box, no error nothing. I must then go to any other open dwg, do a save, and then go back to the original dwg. Then the PLOT command will again work, however, still getting stuck in the preview loop.
I'm using AutoCAD Map 3D 2009.
I've created a simple drawing in CAD that contains a cropped JPEG, a two toned hatched polygon in behind it two MTexts overlaying all.
I cannot view them in either normal plotting, pdf format, jpeg format and even dwf.
I've increased the ram used in the "Raster Extension Options" (2000 MB), I've set the plotting in the "Process Document" to "...In computer", I've saved it in older formats (2000/2004/2007), I've placed the drawing on both our public drives as well as the local, I've adjusted the "Raster and Shaded/Rendered Viewports" & "OLE" settings in the "Device and Document Settings" (None to Best). Not to mention the other variations in the plot menu.
I've tried everything I can think of and have read through several threads here and nothing works.
What drives me nuts about this, is that I'm able to print from a layout with no problems a 3D drawing, with 2D hatching, an extensive title block with hatching and a secondary overall viewport (minimal detail) in the main viewport area.
I'm running Autocad Architecture 2013. My .dwg has about 15 pdf's in it (from a consultant that does hand drawings that I scan in, and use the image manager to insert into my drawing). The PDF's range from under 1mb, to 10mb. The PDFs are in model space and within my various drawing sheets, I show them in my drawing sheets via multiple viewports. I noticed that when I go to plot a sheet that has pdfs shown in viewports, and click on PLOT PREVIEW, the PDF's don't show up - everything else shows up, linework, jpegs, etc, but not the PDF's! I fiddled with the viewports and noticed that if some part of the PDF's image frame was visible in the Viewport, the PDF would appear in Print Preview. But if the viewport sat directly over the PDF's image frame, the PDF would not show up in the Plot Preview!!!
Could it be I've exceeded the maximum number of Viewports in my entire .dwg? (I have about 16 sheets), Or, could it be some mysterious autocad system variable that I'm running up against.
I'm creating a new project drawing and have x-ref'd my base drawing onto the sheet to be plotted. I can see the base drawing thru the viewport while in layout, but once I try and preview my plot the drawing inside the viewport is not visible. that is, I can see the preview of my sheet border & title block, but nothing within the viewport shows on the preview screen.
View 3 Replies View RelatedI tried printing a plan with my printer and for some reason it wont print in portrait mode, no matter how much i change the settings it does not change the page orientation, the preview also shows it to be in landscape mode
View 3 Replies View Relatedwhen i print somthing out i always find that the printout is in wireframe mode. How do i print the so that it is in ' hidden' mode or anything that is not wire frame. i have tried turning the view to 'hidden' and then using 'display' in the plotting options.
View 3 Replies View RelatedWhen Im in model mode mode I create txt to annotate my diamentions, when I sent up my page in paper mode and plot it to a pdf, all the text ive created in model mode appears on the pdf as outlined text ( hollow ).
View 1 Replies View Relatedwhy I get these unusual radial lines showing up in my plot preview. The drawing looks fine on the screen but when I go to plot I get hundreds of lines that converge to a point in my preview.
View 5 Replies View RelatedExcuse my awkwardness but I'm self taught on AutoCAD & have managed fine for last few months but have encountered an issue this evening I can't resolve. I've produced drawings, basic they may be, but when preview them the actual drawing area is barely noticable & when export to pdf it practically prints a blank page. I have very simple items in drawing, stockpiles, excavations test locations, and have been producing pdf's fine, even as recently as this morning using the same cadfile. But what ever I've managed to do since then has changed something and I can't resolve the issue.
View 6 Replies View RelatedUsing ACAD 2008, I am having an odd problem where when I print preview/plot this drawing with a viewport the result is a blank page but when I remove the viewport it plots fine.
View 0 Replies View RelatedWhen I try to plot my drawing, my drawing only takes up 2/3 of the page on print preview. The top half of the page is blank. How can I make my drawing take up the whole available page?
View 9 Replies View RelatedFor some reason, my plot style is applied to my viewports. So for example, when I choose a monochrome plot style for the layout, the view ports in that layout display in black and white. I want to disable this. Is there a system command to turn this off?
View 2 Replies View RelatedHave a dwg with two layouts sheets that print to pdf in paper space - one layout works just fine the other NOT.
Both include one view port and a few small details as pdf underlays(@ 150 kb each) in the PAPER space layout.
The problem sheet - ran a very slow plot preview but it did complete a full view of the layout, then when selected to do the plot it never completes the pdf.
I tried a pdf plot of the same area in MODEL space and it previews just fine and plots to a pdf just fine.
the grey or coloured lines on screen are plot in black, even in the pdf preview. How can I obtain the chosen colours?
View 3 Replies View RelatedThe Autocad 2013 x86 or x64 is not installed on Windows 8 Consumer Preview because programs can not read .NET Framework versions 2 and 4 which are integral parts of the OS.
View 5 Replies View Related