I work in both metric and imperial dimensions. I specify european cabinetry, and most of the architectural drawings i receive are for US clientelle so they're in ft and inches. When dimensioning, it's important that the cm dimensions are accurate for the factory, but the inches are accurate for the contractors.
So my drawing had 1 plan and 4 elevations. All drawn correctly. All scaled together, never one at a time. Yesterday morning everything printed correctly with this drawing.
Randomly, after some very minor changes to the drawing, 1 elevation remained at the correct scale and the plan, and 3 elevations randomly scaled down and at different scales from each other. Also, when i plotted this to a printer it matched what was on the screen. When i plotted it to PDF immediately after, the PDF's reflected 5 totally different scales where all 5 drawings and didn't match the screen or print. For example: a cabinet height in one elevation was 87cm, the next 86cm , and the next 83.9cm. Printed to pdf at totally different dimensions (see attached).
The file was closed and reopened, and the plan, and 2 different elevations were at an even different scale, smaller scale than before. They more closely matched what I got when plotting to a PDF.
I purged, and audited (no errors found), I copied only the bare bones necessary info into a new document, and scaled everything by reference to the size it needed to be. Most of the drawing automatically corrected themselves to the correct dimensions with the one step.
However, certain lines on my plans scaled at a far greater scale, while one wall was accurate, and one wall was off just a fraction. So even though i selected the entire thing and scaled it up together, different layers scaled differently. Basically i had to redraw the plan almost entirely.
The same happened with 3 of the 4 elevations. One section scaled correctly, one section scaled more than it should have and made that portion off.
So i had to redo that elevation as well.I created guidelines and set them where they need to be to align every single wall and cabinet and locked the layer in the hopes that if things move again, the guides will remain.
This has happened randomly with drawings previously, but only by a degree of .1 to .3 cm. I figured this was from scaling the drawings and dimension accuracy. While that was annoying, it was minor. This time we're looking at 2-8 inches difference which can really mess up a job if unnoticed.
what could cause only portions of drawings to scale differently than the rest and at random times even when the scale command hasn't been used? And between closing a document and reopening it? AND from printing to a printer and to a PDF?
I have often problem with drawing view labels. When model is changed and I switch to the drawing then the label is moved to an random position. There is possible to little move with view, or edit label text or switch off/on label and label move back to correct position. This is very unpleasant when there s more views in drawing, is necessary to correct each label.
I have a 2D drawing that is drawn if full scale, it is 26feet wide approximate and 20 feet tall. I need to scale down to fit on a 4 X 8 for a mockup, i have tried using the scale command, but to no avail.
I'm trying to scale down 3D drawings but when I use the 3DSCALE command the perspective gets distorted. Is there a way I can scale my drawing without messing up the perspective?
I need a way to properly scale a drawing that I've pulled into AC..
Example, I get a drawing for customer in PDF that I have to trace into AC. Said PDF is marked 1/4 = 1. Up to this point I've been guessing at accuracy by measuring doors to 3'. I know this cannot be the prefered way
When I upload a drawing from the internet I save it as a wblock.when I insert it into my exixsting drawing it is not scaled to the same dimensions as the rest of the drawing.
I change the units to the same as the drawing befeore I save it as Wblock. But Im still having this Problem.
I'm having problems on setting my scaling up in dwg1 that was sent to me. dwg1 did not have any viewports set up. dwg2 has a scale of 1''=20' I need to set up dwg1 to 1 to 1 first, this is my master drawing,
I have a drawing that was given to me by an architect with a scale 1:250 (0.004 in viewport). The architect drew everything in millimeters and it's a Site Plan, why ? I do not know. The units in the drawing are decimal-millimeters.
The page set-up for layout 1 was for 24x36 drawing size (typ.)I know need to make a layout 2 for a sheet size 11x17 but I can not get my viewport to scale correctly. So, if a 24x36 sheet size had a VP with scale 0.004 (1:250) then what is the scale for a sheet size 11x17 ?
I have a dxf file that consists of multiple rectangles (filled). I need to keep the X-Y position of each rectangle / entity the same but scale the size of the rectangle.
So for example, scale by -10%. If its a filled rectangle centered at (1,1) size (2,2) I need it to be centered at (1,1) and size (1.8, 1..
DXF is a text file and I can write a piece of VBA code to go through, decode the text, find the rectangles, scale, save the text file back to DXF.
I am using the dinosaur version of autocad 14. I know it is old but is working great for what I want to do. I learned on 12 and was using 14 when I stopped working 10 years ago.
I am having trouble scaling my drawing. I remember that 1/48 xp is 1/4" scale. 1/64 ?? is that 1/8" scale?? 1/24 is 1/2" scale.
Scale in Layout. I drew my drawing in mm , and I want to use Layout to print it like I saw in a video, but how do I scale my drawing? For example, the counter and shelf I drew is 1:1 in the Model workspace(1600 by 2000mm) but in Layout, for printing on to an A3 sized paper how do I get it to print in 1:40 or something of that sort?
Right now I'm printing by using Fit To Paper with the dimensions included, but I notice our contractors are using 1:30, 1:40 etc. , my boss doesn't mind since I include the dimensions but I reckon it might cause problems in the future.
And is it possible to just select anything in my selection window, even 3/4 of a line? Because right now, I can only select the whole line no matter what, I only want 1/2 of it because I want to cut the whole drawing in half and move it apart.
By the way, is it possible to customize the panel? Instead of switching between tabs constantly, can I make my own panel? I googled this and tried using CUI but it is confusing. I just want certain sections grouped into 1 bar. Like... Draw/Modify/Attach/Windows all on the first panel.
I really want to be able to type in certain commands without hitting Enter, is that possible? If I hit M, it will move the object without me hitting Enter. Can that be done? Maybe not M, maybe Alt+1 to move, Alt+2 to Scale etc. etc.
We have recently been upgraded to Autodesk Map 3D where I work which when we first got it was a big improvement from what we were running. When I first started using the programme I found the lovely little box in the bottom right hand corner where you can change the view scale.
This allowed me, when in paper space, to double click in a viewport then click the drop down arrow next to the Viewscale box, select custom and then type in the scale I wanted (i.e. if 1:200 I typed 200 then hit ok).
However all of a sudden I am no longer able to do this. When I press ok, nothing changes. There are no error messages or any message. It appears to disregard the command. There is also a closed padlock next to this which when hovered over gives the discription "click to link/unlink AutoCAD Map 3D stylisation while zooming". I am unable to unlock this by clicking on it, the padlock seems protected almost so I am wondering if this is my problem?
i'm working on a drawing started by someone else. They do everything in model space...no paperspace and no viewports. drawing and border are both in model space. I'm not used to just model space.
How do i set the scale of the drawing in model space? do i need to use different size borders to get the correct scale? I'm drawing everything 1:1 and i need my final prints to be on 11x17 paper.
on a previous drawingi see that they used a scale of 1/16"=1' but how they determined this scale. going thru other sheets in the setd of drawings it seems that they used different border sizes (but all are printed on 11x17 paper)...some are printed not to scale if they have no set scale...like details.
example of what i need to do:
I need to show a building rooftop plan view (the entire rooftop) on one sheet. on the next sheet i need to zoom into a portion of the rooftop.
normally i would use viewports to do this. but in model space i dont see how this is done. do i need to have a set of different size borders? but how then can i print them on 11x17 without using "scale to fit"?
I have a building plan that needs to be in 1:100. When put my drawing into the new layout its there. Then when I change the scale, my drawing disappears.
I've completed a drawing, with dimensions and everything and I have to reduce it to 1:2 scale to fit my drawing frame. How do I do this without changing the dimensions? Every time I reduce it the dimensions halve as well!
I am updating a drawing that someone has sent me. The drawings are to be scaled in 1/2"=1'-0", but the drawings are all done in metric. So I reset the scale list and set it at 1/2"=1'-0" in paper space ( the paper size I am working with is 8.5" x 11") when I click on the 1/2" scale my drawing becomes huge and I cant see all of it. In page setup manager I have the plot scale at 1:1 and right below that it says 1 mm and under that 1 units. In model space the drawings have been done in 1:100.
Trying to scale a viewport in AutoCAD 2010, and ran into this error "Error: AutoCAD variable setting rejected: "cvport" 3". I've scaled viewports all the time, and this is the first time I've ran into this issue.
I had started placing dimensions in a drawing before I realized that I had to change the scale of the entire drawing.So now I would like to change the annotative scale of an existing dimension style but I am not clear on how to do it.
This would be for any new dimensions that I add.They continue to appear at the old scale. All of the dimensions are correct I would just like to see the dimensioning scaled up to the proper size for the drawing.
I realize that I could just create a new style but instead would really like to know how to change what I am already using.
I have two drawing files of arrows. One inserts uniformly and the other assumes that I want to specify the X and Y scaling separately. These drawing files do not contain blocks at the moment, but may have as some point in the past. I can't find anything in the drawing files that sets the block scaling when there isn't a block in the drawing, but one of them is behaving as if there is and the other one is not. How do I change all of my similar drawing files to insert scaled uniformly?
I see the option to scale uniformly on the insert dialog box, but I need this for a script, so I need to use the command line version.
Here is a copy of my command line for inserting the two drawing files:
Command: -INSERT Enter block name or [?]: Sign-Arrow-12-A-Left Units: Inches Conversion: 1.0000 Specify insertion point or [Basepoint/Scale/Rotate]: 0,0 Specify scale factor <1>: Specify rotation angle <0>: Command: -INSERT Enter block name or [?] <Sign-Arrow-12-A-Left>: Sign-Arrow-16-A-Left Units: Inches Conversion: 1.0000 Specify insertion point or [Basepoint/Scale/X/Y/Z/Rotate]: 0,6 Enter X scale factor, specify opposite corner, or [Corner/XYZ] <1>: Enter Y scale factor <use X scale factor>: Specify rotation angle <0>:
Command:
Note that the first time Sign-Arrow-12-A-Left comes in with no reference to option X/Y/Z, but the second time Sign-Arrow-16-A-Left has the option, and there for requires the extra line of input.
I have a drawing (attached) with the following settings: LTSCALE = 1, MSLTSCALE = 1, PSLTSCALE = 1.For some reason the linetype is not scaling based on the annotative scale. It will update correctly if I change the LTSCALE but for some reason it wants to ignore the MS and PSLTSCALE variables.
As a note, the drawing was converted from a Microstation drawing and the linetype is a converted Microstation linetype.Is there something in the linetype that is doing this.
I think the MSLTSCALE / PSLTSCALE / annotation scales are fantastic to use when showing the details / plan at different scales (1:100 / 1:50 / 1:1) without having to use LTS to show different scales. I am using AutoCAD 2011.However, I noticed one snag. In the old Autocad before the MSLTSCALE was introduced, I used a shape linetype - a sino shape which I created for insulation in the wall cavity as well for curtain in the interior plan layout (with MSLTSCALE set at 0 and LTS set at scale factor at 1 and use paperspace scaling at desired scale.
When MSLTSCALE / PSLTSCALE are set at 1, the sino linetype will of course changed accordingly to different scale .I prefer to keep the MSLTSCALE / PSLTSCALE at the default 1 with LTS at scale factor 1 as I want the dashed linetypes to updated accordingly to the scale. At the same time I don't want to have the sino linetype changed (keeping the sino linetype at constant 100mm width). Is there a way to control one linetype at MSLTSCALE = 0 and keep the rest of the linetypes at MSLTSCALE = 1.
I don't think it is possible as MSLTSCALE is for general setup. Instead I would have to forgo using the sino lintype and used a block instead. But a way to control an individual linetype scaling.
After drawing in model space(1:1 Scale) I then dimension as needed using Annotative Dimensions, Multileaders and MText using the same 1:1 scale. But when I create the variuos viewports on my layout pages the dimensions aren't scaling to the viewport scale.
This is where it may be partly my fault; When I first started using annotative dimensions etc. a box would pop up asking what scale to use. Because I am dimensioning in model space, rather than always seeing this text box I selected "Do not ask again" check box to always use 1:1 scaling.
These are some of the other settings in place;
ANNOAUTOSCALE = 4 Annotation Visibility = ON Automatically Add Scales = ON
When I xref a drawing created by Practicad into my host drawing, the text size shows up less than half its normal size. This occurs regardless of choosing or not choosing any of the radio button options in the proxy info box that pops up when I open the drawing. It happens on both my desktop and laptop. Practicad (MetaLab Inc.) web-x'd into my computer and confirmed the enabler is installed and the issue has noyhing to do with them. My host drawing scale is set to the same scale as the xref.
I have made a landscape model in meters as units in the modeling area. Now, when I want to scale the drawing in the paper layouts, within the viewport, it seems to me like it's scaling as if the drawing was done with millimeters as units.
I think this might have been caused by me starting to draw, thinking I was plotting in with meters as the unit, but then found that it was set as millimeters. I changed the unit setting for the model to meters and that seemed to work fine. But I'm guessing it didn't work.
I have tried using the INSUNIT command and it says the drawing is in 6, which is meters, so why is it scaling as if it was in millimeters on an A3 layout?
I am having trouble scaling my drawing between model space and paper space. I have it drawn in model space at 1:1, and I set the viewport scale in paperspace to 1:15. However, it does not show up as 1:15. I have drawn a 50' line in model space. The viewport is 4" wide in paperspace, so you should be able to see the whole line in the viewport at a 1:15 scale, with some space on each side. However, it does not. I can only see a small fraction of the line.
Eventually after I copy and paste with the clipboard enough times within one drawing, the ability goes away and I can no longer copy and past one item from one drawing to a separate drawing. I need to use the clipboard function because that is the only way of getting an item from one drawing to another.
I have download a clear clipboard function but it doesn't work. Closing CAD and restarting does not reinstate the function.
My Autocad has started a new behavior. When (in Win7) I double-click on a drawing file in Windows Explorer, Autocad opens the drawing file and also starts a new drawing, all in the same session of Autocad. Is there some system variable or Windows variable that controls this?
