I'm having problems on setting my scaling up in dwg1 that was sent to me. dwg1 did not have any viewports set up. dwg2 has a scale of 1''=20' I need to set up dwg1 to 1 to 1 first, this is my master drawing,
View 2 RepliesWe have recently been upgraded to Autodesk Map 3D where I work which when we first got it was a big improvement from what we were running. When I first started using the programme I found the lovely little box in the bottom right hand corner where you can change the view scale.
This allowed me, when in paper space, to double click in a viewport then click the drop down arrow next to the Viewscale box, select custom and then type in the scale I wanted (i.e. if 1:200 I typed 200 then hit ok).
However all of a sudden I am no longer able to do this. When I press ok, nothing changes. There are no error messages or any message. It appears to disregard the command. There is also a closed padlock next to this which when hovered over gives the discription "click to link/unlink AutoCAD Map 3D stylisation while zooming". I am unable to unlock this by clicking on it, the padlock seems protected almost so I am wondering if this is my problem?
I've completed a drawing, with dimensions and everything and I have to reduce it to 1:2 scale to fit my drawing frame. How do I do this without changing the dimensions? Every time I reduce it the dimensions halve as well!
View 9 Replies View RelatedI am updating a drawing that someone has sent me. The drawings are to be scaled in 1/2"=1'-0", but the drawings are all done in metric. So I reset the scale list and set it at 1/2"=1'-0" in paper space ( the paper size I am working with is 8.5" x 11") when I click on the 1/2" scale my drawing becomes huge and I cant see all of it. In page setup manager I have the plot scale at 1:1 and right below that it says 1 mm and under that 1 units. In model space the drawings have been done in 1:100.
View 9 Replies View RelatedTrying to scale a viewport in AutoCAD 2010, and ran into this error "Error: AutoCAD variable setting rejected: "cvport" 3". I've scaled viewports all the time, and this is the first time I've ran into this issue.
View 1 Replies View RelatedI am a beginner for CAD Drawing and a want to scale an entire drawing in just one axis without modifying the dimensions in other.
scale the attached drawing document along X axis by reducing the lenght to be fit into an A4 sheet. Without compensating the markings' visibility.
I had started placing dimensions in a drawing before I realized that I had to change the scale of the entire drawing.So now I would like to change the annotative scale of an existing dimension style but I am not clear on how to do it.
This would be for any new dimensions that I add.They continue to appear at the old scale. All of the dimensions are correct I would just like to see the dimensioning scaled up to the proper size for the drawing.
I realize that I could just create a new style but instead would really like to know how to change what I am already using.
I have two drawing files of arrows. One inserts uniformly and the other assumes that I want to specify the X and Y scaling separately. These drawing files do not contain blocks at the moment, but may have as some point in the past. I can't find anything in the drawing files that sets the block scaling when there isn't a block in the drawing, but one of them is behaving as if there is and the other one is not. How do I change all of my similar drawing files to insert scaled uniformly?
I see the option to scale uniformly on the insert dialog box, but I need this for a script, so I need to use the command line version.
Here is a copy of my command line for inserting the two drawing files:
Command:
-INSERT Enter block name or [?]: Sign-Arrow-12-A-Left
Units: Inches Conversion: 1.0000
Specify insertion point or [Basepoint/Scale/Rotate]: 0,0
Specify scale factor <1>:
Specify rotation angle <0>:
Command:
-INSERT Enter block name or [?] <Sign-Arrow-12-A-Left>: Sign-Arrow-16-A-Left
Units: Inches Conversion: 1.0000
Specify insertion point or [Basepoint/Scale/X/Y/Z/Rotate]: 0,6
Enter X scale factor, specify opposite corner, or [Corner/XYZ] <1>:
Enter Y scale factor <use X scale factor>:
Specify rotation angle <0>:
Command:
Note that the first time Sign-Arrow-12-A-Left comes in with no reference to option X/Y/Z, but the second time Sign-Arrow-16-A-Left has the option, and there for requires the extra line of input.
I work in both metric and imperial dimensions. I specify european cabinetry, and most of the architectural drawings i receive are for US clientelle so they're in ft and inches. When dimensioning, it's important that the cm dimensions are accurate for the factory, but the inches are accurate for the contractors.
So my drawing had 1 plan and 4 elevations. All drawn correctly. All scaled together, never one at a time. Yesterday morning everything printed correctly with this drawing.
Randomly, after some very minor changes to the drawing, 1 elevation remained at the correct scale and the plan, and 3 elevations randomly scaled down and at different scales from each other. Also, when i plotted this to a printer it matched what was on the screen. When i plotted it to PDF immediately after, the PDF's reflected 5 totally different scales where all 5 drawings and didn't match the screen or print. For example: a cabinet height in one elevation was 87cm, the next 86cm , and the next 83.9cm. Printed to pdf at totally different dimensions (see attached).
The file was closed and reopened, and the plan, and 2 different elevations were at an even different scale, smaller scale than before. They more closely matched what I got when plotting to a PDF.
I purged, and audited (no errors found), I copied only the bare bones necessary info into a new document, and scaled everything by reference to the size it needed to be. Most of the drawing automatically corrected themselves to the correct dimensions with the one step.
However, certain lines on my plans scaled at a far greater scale, while one wall was accurate, and one wall was off just a fraction. So even though i selected the entire thing and scaled it up together, different layers scaled differently. Basically i had to redraw the plan almost entirely.
The same happened with 3 of the 4 elevations. One section scaled correctly, one section scaled more than it should have and made that portion off.
So i had to redo that elevation as well.I created guidelines and set them where they need to be to align every single wall and cabinet and locked the layer in the hopes that if things move again, the guides will remain.
This has happened randomly with drawings previously, but only by a degree of .1 to .3 cm. I figured this was from scaling the drawings and dimension accuracy. While that was annoying, it was minor. This time we're looking at 2-8 inches difference which can really mess up a job if unnoticed.
what could cause only portions of drawings to scale differently than the rest and at random times even when the scale command hasn't been used? And between closing a document and reopening it? AND from printing to a printer and to a PDF?
I have a drawing (attached) with the following settings: LTSCALE = 1, MSLTSCALE = 1, PSLTSCALE = 1.For some reason the linetype is not scaling based on the annotative scale. It will update correctly if I change the LTSCALE but for some reason it wants to ignore the MS and PSLTSCALE variables.
As a note, the drawing was converted from a Microstation drawing and the linetype is a converted Microstation linetype.Is there something in the linetype that is doing this.
I think the MSLTSCALE / PSLTSCALE / annotation scales are fantastic to use when showing the details / plan at different scales (1:100 / 1:50 / 1:1) without having to use LTS to show different scales. I am using AutoCAD 2011.However, I noticed one snag. In the old Autocad before the MSLTSCALE was introduced, I used a shape linetype - a sino shape which I created for insulation in the wall cavity as well for curtain in the interior plan layout (with MSLTSCALE set at 0 and LTS set at scale factor at 1 and use paperspace scaling at desired scale.
When MSLTSCALE / PSLTSCALE are set at 1, the sino linetype will of course changed accordingly to different scale .I prefer to keep the MSLTSCALE / PSLTSCALE at the default 1 with LTS at scale factor 1 as I want the dashed linetypes to updated accordingly to the scale. At the same time I don't want to have the sino linetype changed (keeping the sino linetype at constant 100mm width). Is there a way to control one linetype at MSLTSCALE = 0 and keep the rest of the linetypes at MSLTSCALE = 1.
I don't think it is possible as MSLTSCALE is for general setup. Instead I would have to forgo using the sino lintype and used a block instead. But a way to control an individual linetype scaling.
After drawing in model space(1:1 Scale) I then dimension as needed using Annotative Dimensions, Multileaders and MText using the same 1:1 scale. But when I create the variuos viewports on my layout pages the dimensions aren't scaling to the viewport scale.
This is where it may be partly my fault; When I first started using annotative dimensions etc. a box would pop up asking what scale to use. Because I am dimensioning in model space, rather than always seeing this text box I selected "Do not ask again" check box to always use 1:1 scaling.
These are some of the other settings in place;
ANNOAUTOSCALE = 4
Annotation Visibility = ON
Automatically Add Scales = ON
When I xref a drawing created by Practicad into my host drawing, the text size shows up less than half its normal size. This occurs regardless of choosing or not choosing any of the radio button options in the proxy info box that pops up when I open the drawing. It happens on both my desktop and laptop. Practicad (MetaLab Inc.) web-x'd into my computer and confirmed the enabler is installed and the issue has noyhing to do with them. My host drawing scale is set to the same scale as the xref.
View 9 Replies View RelatedI have made a landscape model in meters as units in the modeling area. Now, when I want to scale the drawing in the paper layouts, within the viewport, it seems to me like it's scaling as if the drawing was done with millimeters as units.
I think this might have been caused by me starting to draw, thinking I was plotting in with meters as the unit, but then found that it was set as millimeters. I changed the unit setting for the model to meters and that seemed to work fine. But I'm guessing it didn't work.
I have tried using the INSUNIT command and it says the drawing is in 6, which is meters, so why is it scaling as if it was in millimeters on an A3 layout?
New Responsive Scaling feature is great.
It's enabled me to add an Edge Animate file to my responsive Wordpress site using the Edge Suite Plugin.
Only problem for me is that although the 3.7MB file I’ve created scales perfectly on all devices it struggles to play on smartphones. (I assume it's too big and too power hungry to play smoothly on smartphones - even since I've added a pre-loader.)
So, in an ideal world, what I need is a separate low res Edge Animate file that only plays on smartphones.
Failing that, I’d be happy with a 'Down-level Stage' image which could replace the Edge Animate animation.
For a moment I thought I’d found a solution when I came across this Adobe TV movie: [URL]
Unfortunately this clever solution only works when the new Responsive Scaling feature is NOT selected. As soon as it is selected, the animation no longer changes from one layout size to another when the browser window is reduced.
I don’t mind whether the fix is in Edge Animate, Wordpress or the Edge Suite Plugin - I just want a solution!
We are designing some web graphics for a friend. By "we" I mean me and a guy who lives on the opposite coast.
He did the initial page layout/design as a PhotoShop tif, at 300 dpi, in layers and about 5 inches wide. The idea, on his end, was that it would be a small file size and, therefore, faster to download on my end. With me so far?
Anyway, I'm suppose to convert it to 800 ppi wide, 72 dpi, jpg. Sounds easy enough. Or not Do all the scaling and now the graphics don't look right. None of the layer effects are right!
How do I scale his graphic, for my purposes and, once it's the size I need it, have everything look the way he created it?
Example: Text at that 5 inch wide, 300 dpi size with a one point stroke on it looked find when the graphic was 5 inch wide and 300 dpi, but at 800 ppi wide and 72 dpi, it's all wrong
Is there a preference or something I should be clicking somewhere and I'm just missing it?
I have converted a PDF to DWG and the scale is out, what's the best way to scale it back to its original size?
Scale by Reference? This option works ok but no measurement seems to be spot on apart from the item you used for the scale reference.
I used the program 'Any PDF to DWG Converter' and the drawing scale in the title block is 1:50.
I'm pretty new to AutoCAD, I've been self-teaching myself for about a month so that I can do some floor plan drawings for a company I work for.I've been drawing in 1:1 scale in model space, but when I plot/print to check my work, I print on A4 paper.
My question is, on A4 paper my 1 drawing unit : 1 mm scale plots perfectly. But obviously if I were to compare that scale to real life, it would not be 1:1. How do I figure out the scaling on the viewport to compare to real life?
I have a 2D drawing that is drawn if full scale, it is 26feet wide approximate and 20 feet tall. I need to scale down to fit on a 4 X 8 for a mockup, i have tried using the scale command, but to no avail.
View 9 Replies View RelatedHow do I scale a 3D model that I have imported originally from a ".step" file (or really any 3D model). I have come from SolidWorks, and this was very easy to do. All of the help files indicate that I need access to the original sketch.
View 1 Replies View RelatedI need to know how to set up my dwg so that 1cm = 1in. when I'm drawing.
View 6 Replies View RelatedLets say that I want d drawing to be printed on scalw 1:50 why do I need to input at the plot properties 20mm to 1 unit in order to get it correct?
Also different question. If i want to print on paper roll and the one dimension of my drawing is 297 (A3) and the other dimension is undifined how can i set the paper size? Because under the drop down menu paper size the sizes are all fixed.
I am working on a drawing that started life as a dxf file from a client. I am having problems with the scale of hatching in that whilst I might normally do a line hatch at a scale of 25 to get the same spacing I now have to set the scale to 650.
Initially I had a problem that the scaling in viewports was also wrong but I sorted that one out but I cannot find how to reset the hatch scale to my normal setting.
I am also finding that when hatching it seems to find gaps in lines that it would not normally do. Even after I have filleted all the corners the hatch still in some cases 'spills out'. The measuring and dimensioning tools are all working correctly and show the correct figures.
I'm trying to scale down 3D drawings but when I use the 3DSCALE command the perspective gets distorted. Is there a way I can scale my drawing without messing up the perspective?
View 7 Replies View RelatedWe receive site survey dwgs generated in Civil 3D that contain 3D topos with elevation tags. The elevation tags are clearly scalabe anno objects that scale correctly in the received civil dwg. The elevation tags won't scale correctly in our dwgs - they come in too small to see.
- Both dwg's have units set to decimal.
- I tried copying / pasting the viewport from the civil dwg to our dwg and the text is still too small. This tells me it's a dwg specific variable and not a viewport setting.
- I have Civil 3D object enabler installed, though I don't think this has any bearing.
It would be nice to use the original tags and not have to re-create every elevation tag.
I am having problems to scale 2d objects I use the command scale but when it request a base point it said "extremely small scale factor ignored" I have to do this 5 or 6 times until the command works.
The other thing is that I can not do a 1 dimension scale in 2D.
I am trying to print on a 3d printer and seem to have a bit of a scaling issue with inventor 2012. I saved the .stl file in the same units but still get a scaling issue. Under options when I save it shows a 1:1 scale as well as the correct units.
When printing a .stl file from another computer that has inventor 10 installed we do not have this issue. Seems to be something with the files from 2012.
This is in Acad 2013. This wasn't happening last week, and I don't know what changed. I have a small drawing file with a few point blocks with attributes and some lines I'm trying to insert into a main drawing. I've made sure that both files are set to "unitless" in the following variables:
INSUNITS = 0
INSUNITSDEFSOURCE = 0
INSUNITSDEFTARGET = 0
I've run SCALELISTEDIT on both files and reset them to "metric and imperial scales", and saved both files. The base points in both drawings are 0,0,0. Both files are in the WCS.
I've run audit on both files. I've run purge in the main drawing to make sure it doesn't already contain a definition of the small drawing. I've rebooted the PC and restarted acad.
When I insert the small drawing into the main drawing, the points come in at the correct coordinates. But the lines connecting them and the point block attributes are scaled up by 39.3700787400 and are far away.
How can i scale a block have some attributes , with known factor ?
View 3 Replies View RelatedI need to scale a part up by a ration on 2, but I'm not sure how?
View 2 Replies View RelatedWhen set up my drawing in paper space it is just a big cluster. When i scale it, the drawing disappears. However, when i hit scale to fit it returns but the drawing is still in a cluster.
View 9 Replies View Related