Revit :: Show Edge Of Riser Finish As Hidden Line In Plan?
Jan 18, 2012Is there a way to show the edge of the riser finish as a hidden line in plan?
Also the edge of nosing against the riser to be shown as a hidden line in plan?
ADVERTISEMENT
Revit :: Show Hidden Edge Through Itself
Aug 7, 2012I have a lot of concrete walls that have been cut and shaped in many ways. When I do the show hidden lines command I am unable to show edges of the same object that hides them.
View 1 Replies View RelatedRevit :: How To Show Site Plan That One Line Represent Building Contour
May 16, 2012by default revit shows roof plan in the Site plan view.
Is it possible to show site plan that one line would represent building contour? Also is it possible to cast shadows of all the building if the first floor is selected?
i was trying to make site plan from the fist floor, but since i gave intense topography ground is being cut and i need full topography. i am using 2013 revit.
Revit :: Parapet Interior Wall Finish Above Roof Line
Aug 21, 2012I have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies View RelatedRevit :: Convert 3D Hidden Line View Into 2D Hidden Line Flatten View
Oct 4, 2012How do you convert a 3d hidden line view in Revit into 2d hiddenline flatten view? Or I have to bring it to AutoCAD to flatten it?
View 1 Replies View RelatedAutoCAD Visual LISP / AutoLISP :: Creating A Riser From Blocks Inserted On Floor Plan
Apr 25, 2013I'm looking for an easy way to generate a on-line riser diagram of blocks that have been inserted on a floor plan.Here's what I was thinking.
For every instance where the block SLC_DEVICE IS insert on the drawing, the routine would insert the block listed in the "TYPE" and place text equal to what is listed in the "ADDRESS". The TYPE is the actual block name.
Each one of these blocks have a tag of TYPE and ADDRESS. What is in the TYPE tag is the block name of what should be inserted and what is in the ADDRESS tag is the text that should be inserted under the block.
So for example; the routine would find the first instance and the tag TYPE which is "Smoke_Detector" and the tag ADDRESS which is 01:03:001. The routine would insert the block "Smoke_Detector" with the text "01:03:001" directly under it. It would insert the next instance the same way a specified distance from the last; so on so on so on until all instances of the BLOCK (SLC_DEVICE ) have been inserted.
The other part of this would be the Block "NAC&SPK_Circuit" but you would use the Tags "Type", "Candela" AND "NacCkt" to generate the one liner.
Revit :: Show Hidden Lines Command
Nov 3, 2011I am having a problem with the show hidden line command, because when used in the project I can see dashed lines and continuous lines. I was looking for how to manage the line pattern in this command but there is no way to do it.
See the attached image of my problem.
Revit :: How To Show Dimensions For Window In Plan
Apr 27, 2012How to show dimensions for window in plan , instead of default hexagon (number)
For example 60" x 48"
Revit :: Top Mullion Show Up In The Floor Plan?
Jul 24, 2012I just created a simple winodw family. I don't understand it looks fine in the reference level within the family.
But once I placed it in the project, it only shows the top mullion, I had to delete the top mullion within the family to make the plan view look right. What's the reason of it?
Revit :: Why Imported DWG 3D Model Not Show In Plan
Mar 12, 2013i have just started using revit. i imported a 3d dwg file into generic model family and loaded into my project.for some reason, the model shows in section, elevation and last level of my floor plan and site plan as well, but it is not showing in my 1st to 2nd last floor plan. can some people tell what are to possible reason for this?how can i get it show show in the plans?
View 3 Replies View RelatedRevit :: Possible To Show Symbols In A Plan View
Jan 17, 2013I'm currently looking into switching from Vectorworks to Revit due to a job application I'm being offered. What I really want to know is if the following floor plan is possible to make in Revit. I just want floor plans to be with color to better show the different things on it and make them more clear.
I also want to know if it is possible to show symbols in a plan view other than just a rendered hidden line view of the 3D part of it, so I can have a simplified version for the plan view and a detailed object for the 3D. Like you have a 2D-plan component for the plan views and e 3D component for all other views.
Revit :: Doors Will Not Show Up In First Floor Plan?
Nov 2, 2011Somehow today all the doors and cased openings dissapeared in my first floor plan.
They show up in the 3d views, sections, and second floor plan, but not in the first. I have checked the visibilty settings, and they are all checked and correct, and I have checked the height of my floor cut, which is adequately at 4 feet high. Additionally, if I make the detail level "fine" then the casings will show up around the wall but the wall will not show the door cut. The doors show up in a previous version of the model, so I'm not sure what has happened to cause the dissapearance.
Revit :: Railing Terminations Don't Show In Plan?
Nov 8, 2013I've created custom railing terminations and applied them to a handrail. They appear in every view extept plan. Railing extensions show fine. Railing Terminations don't. I am including screenshots & the families. Visibility is on for all views and all detail levels. Linetype is set to solid in Object Styles and VG. View Range is fine. Cut plane is way above the railing and bottom is unlimited.
The weird thing is that the extenstions appear in blue when the railing is selected. But they dissappear otherwise.
Revit :: How To Show Dimensions For Any Room In Plan / Instead Of Default Area
Apr 27, 2012how to show dimensions for any room in plan , instead of default Area (SQ FT)
For example ....BEDROOM 10' 3" x 10' 0"
Revit :: Show Sloped Rafters In Section And In Plan Correctly?
Mar 25, 2013How to show sloped rafters in section and in plan correctly? The attached plan shows the rafters as a structural beam system and I do not know how to slope the beam system to match the roof pitch.
View 2 Replies View RelatedRevit :: How To Get Roof Beams / Windows To Show As Dash Dot In Floor Plan
Mar 21, 2013Is there a way to get roof beams/windows/etc to show as dash-dot in floor plan without having to make changes in every family or for every new object?
View 3 Replies View RelatedRevit :: Show Rafters Connected To Ridge Beam On Framing Plan?
Mar 21, 2013How do I show rafters connected to the ridge beam on a framing plan? How to show collar ties on this framing plan or section?
View 3 Replies View RelatedAutoCAD Inventor :: Unable To Show Hidden Line Of Pattern By Direct Selection Of All Object
Dec 30, 2013I am facing small problem with inverter drafting. I am unable to show hidden line of pattern by direct selection of all object . I have to select one by one item from pattern.
In my drawing there is tie rod item ( find attached file) i have shown hidden line of only this part . and i have to select all items one by one.
Revit :: Removing Riser While Creating Stairs?
Nov 29, 2012I have been trying to create a stair case but i can not get the top of the stairs to line up correctly. When i do gent one platform to line up the riser sticks up above it.
View 4 Replies View RelatedRevit :: Create Non-plottable Line Style That Is Only Visible In Plan View?
Feb 23, 2012Is it possible to create a non-plottable line style that is only visible in a plan view? I want to use something other than the invisible line.
View 3 Replies View RelatedRevit :: Show High Level Walkways And Balconies On Ground Floor Plan In High Volume Space?
Nov 15, 2012How do I show high level walkways and balconies (in dashed outline) on the ground floor plan in a high volume space?
Obviously I can turn the first floor RCP on in the view and manually draw the information, but I assume these lines won't move if the walkways above move (or am I wrong?). Also this seems slightly wrong given the amount of automation available.
Revit :: Reflecting Ceiling Plan In Plan View?
May 30, 2012I am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
View 7 Replies View RelatedRevit :: Show Level Of Cut On Profile As Reference Line Automatically?
Oct 2, 2012How to show the level of cut on the profile as reference line automatically?
I’m wondering if there is a way to show the level of cut automatically on the elevation view.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Revit :: Modify Tab Missing Finish And Cancel
Feb 10, 2013I just installed the student version of Revit 2013. I opened it and everything seems to be working expect when I draw anything (ie topo surface, wall, etc.), the modify tab is missing all the draw options (line, circle, etc) as well as the Finish and Cancel buttons. This makes it impossible for me to use the software without those. Is there a way they could be hidden or is the software just corrupt?
View 3 Replies View RelatedRevit :: Get New / Existing Rooms Into A Room Finish Schedule
Jan 27, 2012I have a project that has existing rooms that need to stay existing and new rooms. Is there a way to get both types of rooms into a Room Finish Schedule?
I can't seem to get both to coexist in one schedule. I would hate to place New room in the new construction phase to make this happen.
Revit :: How To Insert Blank Value For Ceiling Heights In Finish Schedule
Apr 2, 2008With no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 7 Replies View RelatedRevit :: Can Ceiling Type Be Linked To Room Finish Schedule
Feb 8, 2013In a recent meeting wtih cilent, we asked her to review the Finish Schedule. She pointed out that one of the ceilings was supposed to be gypsum board rather than ACT. Looking on our RCP, it was showing gyp board, but the schedule, which is populated from the Room Properties, was calling out (the non-updated) ACT 2x2.
Is there some way to link the ceiling type directly to the finish schedule directly, rather than make double changes (updating the room properties and the actual ceiling type) in order for the proper information to be showing? Seems odd and not very useful to have this kind of redundancy and something that should have been worked out long ago in Revit.
Revit :: 2013 - Edit Boundary Tab On The Ribbon As Well As Finish Sketch?
Nov 6, 2012I am encountering issues with the "edit boundary" tab on the ribbon, as well as "finish sketch" when the edit boundary tab DOES show up. i don't know how to finish the sketch without this, so i have to undo everything.
View 1 Replies View RelatedAutoCAD Inventor :: Reference Line - Hidden Line Removal?
Jan 24, 2012how to make the lines of a reference part that are in effect acting as hidden lines become removed from a view?
We've tried making the part phantom...which isn't right as we need the line representation of the part to be as the reference linestyle...
We've tried changing variables & tick boxes in the edit view dialogue boxes...but nothing works...
AutoCAD LT :: Continuous Line At Beginning And End Of Custom Hidden Line
Jul 9, 2013I made this custom hidden line, here is the defiinition:
*SCADA_FO_HL, - - - -SCADA-FO- - - -SCADA-FO- - - -SCADA-FO- - - -SCADA-FO- - - -SCADA-FO- - - -SCADA-FO- -
A,0.2,-0.4,0.2,-0.4,0.2,-0.4,0.2,-0.4,0.2,-0.4,0.2,["SCADA-FO",STANDARD,S=.375,U=0.0,X=1.0,Y=-.1],-5
It leaves a continuous line at the beginning and end of the line. Is there a way to get rid of that?
AutoCad :: How To Change Line From Solid To Hidden Or Dashed Line
Sep 7, 2013I must be missing something fundamental when trying to change a line from a solid line to a hidden or dashed line in Autocad 2000. I use the ltype command then load either Hidden, or dashed ISO,or both, and invariably the scale is way off in that I always end up with a still solid line, after using modify properties. After all that, every line I draw after that comes out dashed. Maybe I should fool with the layers? Is there a basic procedure I should follow here?
View 2 Replies View Related