With no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 7 RepliesIn a recent meeting wtih cilent, we asked her to review the Finish Schedule. She pointed out that one of the ceilings was supposed to be gypsum board rather than ACT. Looking on our RCP, it was showing gyp board, but the schedule, which is populated from the Room Properties, was calling out (the non-updated) ACT 2x2.
Is there some way to link the ceiling type directly to the finish schedule directly, rather than make double changes (updating the room properties and the actual ceiling type) in order for the proper information to be showing? Seems odd and not very useful to have this kind of redundancy and something that should have been worked out long ago in Revit.
I have a project that has existing rooms that need to stay existing and new rooms. Is there a way to get both types of rooms into a Room Finish Schedule?
I can't seem to get both to coexist in one schedule. I would hate to place New room in the new construction phase to make this happen.
Is there a way to get the ceiling height automatic in a schedule?
View 4 Replies View RelatedWith no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 3 Replies View RelatedHow to change the appearance of lines in a room finish schedule? I want to be able to have some appear bold, others to be a double line, and some to be thin? Currently when i load the standard room finish schedule the lines are not what i want them to look like.
View 1 Replies View RelatedAny way using autoCAD LT 2014 to get CAD to display the elevation heights of survey points without having to type the heights in text bozes next to each individual point. i can insert a field which displays the elevation of the point but doing this again i would have to do every point individually.
Another words is there a way to select all the survey points required and get CAD to display a certain property, which in my case is the elevation height of that survey point, next to it? so it looks like x 23.35 x 23.57 etc..
I'm using autocad 2008, and up till now I have never had to draw a 600x600 ceiling grid into a room (I always adjust what others have done before me), now i can do it in a lot of different ways but are all time consuming, but i bet there is a easy auto fill/fit way of doing this.
View 9 Replies View RelatedIs there a way of displaying mounting heights of fixtures and fittings on elevation in revit architecture, like using a 300mm grid or something
View 1 Replies View RelatedI have a 3 story building. We are almost finished with design development. I need to raise the building's first floor which will cause all the other floors to change their level heights. I have been told that we need to fake in level markers because to change the level heights will cause all the information (for example dimensions) to disappear because they are 'tied' to the original level height. Is there a way to raise the building without loosing all the work that has been done?
View 9 Replies View RelatedAny example of inserting a schedule tag?
View 1 Replies View RelatedIs there a better way of achieving this (screen snip attached). To get the roof segments off lower plate heights I have added in temporary walls corresponding the higher plate height, picked by footprint then extended the overhang on these segments to hit the lower plate height. Then erase the temporary walls. But this detaches the edit footprint-edit overhang function.
Is there a better way? If only a line element would host a roof to enable slope and overhang association.
I just installed the student version of Revit 2013. I opened it and everything seems to be working expect when I draw anything (ie topo surface, wall, etc.), the modify tab is missing all the draw options (line, circle, etc) as well as the Finish and Cancel buttons. This makes it impossible for me to use the software without those. Is there a way they could be hidden or is the software just corrupt?
View 3 Replies View RelatedIs there a setting to export the grid lines of ACT ceiling in a 3D view to DWG?
I don't know if there is because I can't even get the grid lines to show in a 3d view. Right now the view shows the ACT ceiling as a simple geometric shape.
I read a 2009/10 thread, "Rotating lighting", describing how to work around the problem of family lighting fixture members not rotating. I would hope there is a better solution today.
I simply want to place a lighting fixture - std 2x4 flourescent, on a 7 deg sloped ceiling. The axis of rotation is the long run of the light fixture. Is this not possible in Revit 2013?
Or, do I have to dredge up the work around from 3 releases ago and attempt to discern how to make it work?
It seems like I should just be able to set the family to use a work plane-based assignment and then place it with the correct work plane active. That is not happening. The light fixture doesn't want to rotate the 7 degrees to align with the work plane.
Basic master bedroom with a view. roof has a 9 pitch. I cannot figure out how to put a cathedral ceiling in. How do you?
View 4 Replies View RelatedI have an exterior wall with plaster and lathe on the exterior, and gyp board on the inside. When I edit the wall structure, and modify the layers so that I can take the interior wall finish only up to the sheathing line, the wall does not join at the corners properly. It leaves a gap for the interior fininsh at a corner above the sheathing line when looking in 3d. What are you all doing with parpet walls and the interior finishes above the roof line?
View 1 Replies View RelatedI am encountering issues with the "edit boundary" tab on the ribbon, as well as "finish sketch" when the edit boundary tab DOES show up. i don't know how to finish the sketch without this, so i have to undo everything.
View 1 Replies View RelatedI am laying out a simple structure. Bearing wall to bearing wall is 35’, with a few non bearing walls between the bearing walls. I will be using a truss to span from bearing wall to bearing wall. What would be the best work flow for the drywall ceiling material. The ceiling seems to require a core element. I cannot seem to manage drywall alone. If I create a ceiling with 2x4 core and drywall finish and create a ceiling over the whole area the ceiling seems to auto dim to the ceiling finish and not the core 2x4. Then there is the issue of the clean up at the top plate were the wall and ceiling finishes meet
View 1 Replies View RelatedI have one of the floors in our building doing something wacky. The 5th floor reflected ceiling plan looks fine so I create detail plans for the suites at a different scale. this new suite blowup has what looks to be the same suite but everything is greyed out and when i switch from coarse detail to fine detail it doesn't do a thing.
The orignal full reflected ceiling plan looks fine. The line are black. The detail swithces back and forth... I can;t figure out what the problem could be. I used the same process on other floor and everyting is OK. The View Ranges are the same and everthing else in the properties seem the same too.
I have a problem. The linked model from our electrical engineer its lights are at the correct height but the ACT ceiling is still running its lines throiugh the lights. how do we take care of this to where the linked model which has the lights in it cut through our ACT ceiling from our central model?
View 2 Replies View RelatedI'm using Revit 2014 & have not been able to fade the ceiling grid lines so they don't plot out so heavy on my dwgs. I've tried overriding graphics of these grids with half tone which didn't work then I tried transparency & that did not work. They either stay on or turn right off!
View 4 Replies View RelatedAre there any plans to add the simple yet productive feature of moving an object in the X and Y directions at the same time?Also, I would love to be able to select the ceiling grid and hit the space bar and have the grid rotate 90 degrees.
View 4 Replies View RelatedI'm use to working with autocad layers.In AutoCAD if I'm drawing electrical plan and floor plan, HVAC...ect I just freeze in viewport the things I don't want to see for that particurler sheet.
In Revit I duplicated my floor plan to create my electrical plan. I can add my recepticals and switchs but it won't let me add light fixture. Do I add the light fixture to ceiling plan then some how move them to my electrical plan?
How can I move my air vents to the ceiling plan from the floor plan ?
View 1 Replies View RelatedI have fixtures on the reflected ceiling plan showing up in the foundation. How to stop this
View 1 Replies View RelatedHow We can to change the default height Ceiling plane In Project Browser.
For example, the Default is 2600mm.
I want to Over 2800mm set.
Not in Time Drawing Ceiling.
I want to place a Skylight on a Slope Roof that will be channel vertically thru the Raked Ceiling System. I need to show this skylight on Roof and Ceiling plans. without tracing lines or using Vertical command.
View 3 Replies View RelatedIs there a way to show the edge of the riser finish as a hidden line in plan?
Also the edge of nosing against the riser to be shown as a hidden line in plan?
Any lighting fixture families in revit Architecture that snap to the ceiling grid? I've seen them in Revit MEP. Would be a lot nicer than having to align them manually.
View 1 Replies View RelatedI've got some troubles creating a proper ceiling plan. What goes wrong (imo) is that my wall sweep is shown on my ceiling plan while it shouldn't.First image shows the ceiling plan. (on image 3 you will see the wall sweep I mentioned in red).
This image shows the view range used.This images shows the section (right), 3d (top left) and ceiling plan (bottom left) highlighted the wall sweep.Why / how do I prevent this wall sweep from showing up?