I have some stairs which I want to be on a certain level however they are not going onto that level. I have made each row of them into a group as they are for a theatre.
View 6 RepliesI noticed that Revit likes to show the entire stair going down. This works for me in a lot of cases but I have a project that the second floor is showing the stair all the way down to the first floor, and there is another stair going from the second floor to the third that I really need to see.
Plan regions don't seem to allow me to add a break line below the second floor and see the stair from the second to the third floor. The floors are on and the view is set to hidden.
The attached png shows the up stairs in blue that I would like to see and the Down stairs I would like to cut at the landing.
I am having a little trouble with some doors showing up on the level 1 door schedule that are actually on level 2. They are curtain wall doors.
View 6 Replies View RelatedThe underlay does not show up for Level 1 when I am on Level 2, but it does show up for Level 2 when I am on Level 1. the underlay option is on for Level 1, so I'm not sure why it's not showing up. I am using Revit 2014.
View 1 Replies View RelatedMy stairs go from Level 1 to 2 and join a concrete floor at level 2.
The stairs are monolithic.
The problem I have is that at the top of the stairs the end riser can be seen and so it appears as an extra tread when viewed in plan.
See attached file, the red cross marks the lines which I need to remove.
I cannot join the stairs to the slab.
How can I remove these lines - is there something better than a masking region? can I set something in the family?
I have a stair that along one side of the sloping part is a window. I have 2 railings along this stair, 1 is a chair rail, the other is a wainscot panel. Obviously the chair rail and wainscot cannot be built to cover the window.
How can the railings be "cut" around the window?
I know how to start/stop the chair rail, but the wainscot needs to continue under the window (keeping in mind that the window is horizontal and the wainscot is sloping with the stair.)
I can't seem to get the stairs to cut say half way down. The normal view range for the view doesn't cut it, and neither does a plan region. Going up is great, I don't see why cutting it down is so difficult...?
View 5 Replies View RelatedI have the following flights of stairs running down one side of my building:
Landing, 6R with 170mm height, Landing, 3R with 190 height, Landing, 7R with 182 height.
I've modeled this as 3 separate flights of stairs because of the 3 different riser heights. The top landing is a floor slab, as is the bottom landing. I've modeled intermediate landings as either the top or bottom tread of a flight. How do I deal with the junctions of these stairs? The monolithic concrete will not join. The materials of both components are set to <By Category>.
My stairs won't extend up to second floor. I am using Revit 13 and have created many stairs in past with other models. I have tried stair by sketch and stair by component but they keep stopping about 2 feet short of the floor drawing a standard U shape.
View 2 Replies View RelatedSee attachment.
I can't figure out why the bas is visible through the floor :s while the middle part is not. The part where you can see the color of the stairs is cut out of the floor.
I'm trying to create a flight of stairs by component (Revit 2013). When I view them in 3D I notice that one of the walls from Level 1 that should be "cut" where the stair run intersects the wall @ top of wall, does not cut and instead goes through the staircase up to level 2. How to get this wall to be "cut" following the rise of the stairs? I've remade the stairs dozens of times and it still does not automatically cut the wall.
View 2 Replies View RelatedI have been trying to create a stair case but i can not get the top of the stairs to line up correctly. When i do gent one platform to line up the riser sticks up above it.
View 4 Replies View RelatedHow do you assign an exisiting stairs to be the host of a new set of railing?
View 1 Replies View Relatedwe are using a custom font throughout the whole project, I need to use the same font within the stairs family , how do I change the "DN" in stairs to the other font?
View 5 Replies View RelatedI am trying to control the height of the camera for a walkthrough so that I can go up stairs. I know that I can activate the "Mini Tour Building Wheel" and can do it that way but it is very clunky to use and I don't always get the right angles. Is there a simple way to control each key frame's heights like you normally would a camera (eye and target elevations)?
View 1 Replies View RelatedWhat is a good way to finish up the monolithic stairs?
- How can I join the top tread to the upper floor slab? (red circle in attached sketch)
- And is there a way to join the CIP monolithic stairs to the CIP walls? (blue circles)
I have a situation of one sloped floor connecting two horizontal floors. They build together a continuous surface.
I need to join them and have the layers be continuous along the structure. If they were roofs, no problem, I could use the "roof by extrusion" command.
Should I do that? If I try to use floors.....
When I model them as three separate floors, and then Join them, it doesn't work. meaning that the layers within the floor don't match (well, they can't, in fact! I have to move the floor behind!)
If I model one single floor and then add split lines, and move them... it does work. BUT..... I have a stairs on top of it! the stairs have a different slope than the floor, and i need to build a variable layer that fills the void between the floor and the stairs.
So my hypothesis was: I put a sloped floor through the slope arrow... and then adjust one variable layer to do the inflill...
My dream would be to join then floor and stairs.... The material is the same
Why am I getting different dimensions and locations in plan and section views for stairs?
View 4 Replies View RelatedI'm doing as-builts of a historic structure and the walls are very slightly out of alignment with the x-y axes. Whenever I'm drawing something that's nearly (but not quite) horizontal or vertical, Revit forces it to be aligned to x-y axes. I don't want that but don't know how to turn it off so that it snaps only to my crooked geometry.
View 3 Replies View RelatedI've seen it used quite a bit on TV recently, particularly in history documentaries, where they've taken a picture (often an old image such as the bayeaux tapestry or an old painting) and sort of 'disassembled' it and added effects, to give a front-to-back semi-3D look, almost as though the figures and elements in the picture were flats in those old-fashioned toy theatres, or maybe a pop-up book.
I've had some experiments in achieving the look in PS, using things like drop-shadows, and slightly blurring foreground and background elements, but it never quite looks right; often there's some impression of depth but the 'space' isn't quite there.
If there is no level 3 in the project browser. How can you add a 3 level to the project.
View 2 Replies View RelatedIs it possible to copy a phase from one level to the other. For example, on Level 1 I have walls that are Existing, Demo, and New Construction.
If I select the objects and copy to clipboard and paste the objects to another level they will all switch to New Construction. Is there any way we can have the walls remain the same phase when copied to another level?
Is there a way to set the visibility of elements in a 3D view according to the Level they are associated with?
The VG tab which opens the filter dialog provides a check box for the "Levels" category, and the relevant parameters are made available.
But I can not seem to create a filter rule which evaluates any of those parameters (name, elevation, etc...) to then isolate the visibility of those elements in the 3D view that either meet, or do not meet the criteria. Nothing seems to work.
To achieve a "similar" effect in a 3D view, I can use a Section Box, but that is a very clunky and imprecise way.I can also create a Shared Parameter for "Level" and perhaps filter successfully that way, but that seems redundant with the Levels intelligence already established.
It is almost seeming like you should not try to creat these views in templates to get a jump start on projects. but for the life of me I am not understanding how you can get level lines to appear elevations that have already been create. or in new ones?is there away to successfully get these back?
View 3 Replies View RelatedThe “level” indicators are not cropped exactly based on the “crop region”,the “crop view” doesn’t crop the “level” indicators exactly as they extend outside the “crop region”.
View 4 Replies View RelatedI've added some levels that are pretty close together. In elevation and section the labels overlap. How do I bend or crank the elevation line at the end so that the labels don't overlap?
View 2 Replies View RelatedI accidentally deleted the side (left side default) tool bars and how do i get them back?? I cant find the buttons in the main toolbar (top).I got the properties toolbar back but i am still wondering how to get the level toolbar back(that shows you all the different views)
View 1 Replies View RelatedWhen I open a number of templates, I will see a Basement Plan, however when I go the the Elevations I do not see a Basement Level.How do I add the Basement Level to the Elevations ?
View 5 Replies View RelatedI've been trying to construct a wal with the start leve being the ground floor and the finishing Level being First floor level. every time i try to do this tho i get this message occur
"Top Constraint is invalid for the Level."
I'm creating a Construction Template in Revit 2014. When I create new levels these appear in Floor Plans and automatically generate a new Structural Floor Plan view with the new levels but the previous levels don't appear (those that come in Revit by default).
I dont want to delete the level 0 which comes by default.
I've got a model and i created a new level as normal, propogated extents etc but when i created as section North to South (Vertical) in the model the level does not show. When i create a section from East to west (horizontal) then the level appears fine. I've tried creating many sections and this is always the case. If i select a level in the section and click on select all instances in entire project the number includes the additional level but i can't see it. It is not hidden in the view, not on a different workset or anything unusual...
View 5 Replies View Related