The underlay does not show up for Level 1 when I am on Level 2, but it does show up for Level 2 when I am on Level 1. the underlay option is on for Level 1, so I'm not sure why it's not showing up. I am using Revit 2014.
View 1 Replies
I have trouble showing Underlay for level view when dealing with in-place walls. Basically, they dont work with Underlays - nothing shows up (even in wireframe mode).
Please have a look at attached file, dropbox link: [URL] ....
There is a Blend wall that starts on Ground level and goes as high as Top level. When you check whats visible on different levels (and RCPs) everything is fine (views respond to changing cut level and so on) - but when you try to Underlay one of the level views - nothing shows up. Basic idea is to show top edge for tracing with Linework tool - so it shows as Overhead.
I am having a little trouble with some doors showing up on the level 1 door schedule that are actually on level 2. They are curtain wall doors.
View 6 Replies View RelatedHow to show the level of cut on the profile as reference line automatically?
I’m wondering if there is a way to show the level of cut automatically on the elevation view.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I am working on a project with Split Levels like a Multi-level CarPark. I need to produce plans by combining two Levels which are at 3M height difference.
While using Plan Region, Some of the walls dont show as cut, though their height is more & above the Cut Plane Level.
I did find a quick solution online here - [URL] ... This trick is still not working for some of the walls..
I am currently working on a project and i created a land plot and set each level line to the proper elevation but not all of the level lines appear in every view. In the North view all of the level lines and the walls i have created appear, but the walls don't show up in any of the other views. Also the North, West, and South views show all of the level lines but the East view does not.
View 1 Replies View RelatedHow do I show high level walkways and balconies (in dashed outline) on the ground floor plan in a high volume space?
Obviously I can turn the first floor RCP on in the view and manually draw the information, but I assume these lines won't move if the walkways above move (or am I wrong?). Also this seems slightly wrong given the amount of automation available.
I am trying to adjust the noise level with the level tool but its not working. I move the arrows every which way see that it changes. I get it to were i want it them press ok and it only changes a little bit.
It become what it was in the preview. The level tool works when I add it as a new adjustment layer but I don't want like that I want to be able to copy the new level of noise I just made and can't if I add new adjustment. what should I do to fix this? O and this is the trial version and It wasn't working earlier with lots of other tool but i uninstalled it and now they are working except the level tool how I want it to.
I tried to use shortcut Ctrl+L to access Level... But, my Photoshop Elements 9 did not respond and the Level window did not show up.
View 5 Replies View RelatedSay I have an image where I'm attempting to extract a mask from and I've found that one of the channels will serve as a good starting point. Further suppose that I have found that I want to increase the luminance level of pixels in the range of 60 - 65 by 10 luminance levels each:
i.e. all pixels with luminance values of 60,61,62,63,64,65 would, after the operation have luminance values of 70,71,72,73,74,75. Is such a thing possible with Photoshop?
If Inventor 2010 has the capability of showing certain parts/sub-assemblies in phantom style lines on the idw/dwg file?
I have a box unit, where I want to show the base, but with the posts meeting it in phantom. Then when I do the drawing for the posts, I want the base and roof in phantom. Then when I do the roof drawing, I want the posts in phantom again.
I can't change the BOM level as it will apply to every level of detail. when suppressed, they completely vanish. Is there a way to do it rather than find the parts in the browser (whilst in the drawing) and change the properties (over-riding them)?
I want to show only the lowest level of folders in my LR LIbrary module. Used to do that but somehow got changed. Now shows parent folder, 2nd and 3rd levels. If I uncheck INCLUDE SUBFOLDERS it just gives me a zero photo count for the parent but still shows the folder and I still ahve to click levels to get to the photos. If I right click on parent folder....someone said to click Promote Subfolders......I do ot have this choice!
View 2 Replies View RelatedIf there is no level 3 in the project browser. How can you add a 3 level to the project.
View 2 Replies View RelatedIm using AutoCAD 2007.
I have done a land survey showing a top of bank - and the bottom of bank, which ive then contoured by using Carlson Survey (AutoCAD engined).
Im trying to draw cross sections through my model that would obviously show the level of the surface.
The bank lines and contour lines are polylines.
Is it possible to copy a phase from one level to the other. For example, on Level 1 I have walls that are Existing, Demo, and New Construction.
If I select the objects and copy to clipboard and paste the objects to another level they will all switch to New Construction. Is there any way we can have the walls remain the same phase when copied to another level?
Is there a way to set the visibility of elements in a 3D view according to the Level they are associated with?
The VG tab which opens the filter dialog provides a check box for the "Levels" category, and the relevant parameters are made available.
But I can not seem to create a filter rule which evaluates any of those parameters (name, elevation, etc...) to then isolate the visibility of those elements in the 3D view that either meet, or do not meet the criteria. Nothing seems to work.
To achieve a "similar" effect in a 3D view, I can use a Section Box, but that is a very clunky and imprecise way.I can also create a Shared Parameter for "Level" and perhaps filter successfully that way, but that seems redundant with the Levels intelligence already established.
It is almost seeming like you should not try to creat these views in templates to get a jump start on projects. but for the life of me I am not understanding how you can get level lines to appear elevations that have already been create. or in new ones?is there away to successfully get these back?
View 3 Replies View RelatedI noticed that Revit likes to show the entire stair going down. This works for me in a lot of cases but I have a project that the second floor is showing the stair all the way down to the first floor, and there is another stair going from the second floor to the third that I really need to see.
Plan regions don't seem to allow me to add a break line below the second floor and see the stair from the second to the third floor. The floors are on and the view is set to hidden.
The attached png shows the up stairs in blue that I would like to see and the Down stairs I would like to cut at the landing.
The “level” indicators are not cropped exactly based on the “crop region”,the “crop view” doesn’t crop the “level” indicators exactly as they extend outside the “crop region”.
View 4 Replies View RelatedI've added some levels that are pretty close together. In elevation and section the labels overlap. How do I bend or crank the elevation line at the end so that the labels don't overlap?
View 2 Replies View RelatedI accidentally deleted the side (left side default) tool bars and how do i get them back?? I cant find the buttons in the main toolbar (top).I got the properties toolbar back but i am still wondering how to get the level toolbar back(that shows you all the different views)
View 1 Replies View RelatedWhen I open a number of templates, I will see a Basement Plan, however when I go the the Elevations I do not see a Basement Level.How do I add the Basement Level to the Elevations ?
View 5 Replies View RelatedI've been trying to construct a wal with the start leve being the ground floor and the finishing Level being First floor level. every time i try to do this tho i get this message occur
"Top Constraint is invalid for the Level."
I'm creating a Construction Template in Revit 2014. When I create new levels these appear in Floor Plans and automatically generate a new Structural Floor Plan view with the new levels but the previous levels don't appear (those that come in Revit by default).
I dont want to delete the level 0 which comes by default.
I've got a model and i created a new level as normal, propogated extents etc but when i created as section North to South (Vertical) in the model the level does not show. When i create a section from East to west (horizontal) then the level appears fine. I've tried creating many sections and this is always the case. If i select a level in the section and click on select all instances in entire project the number includes the additional level but i can't see it. It is not hidden in the view, not on a different workset or anything unusual...
View 5 Replies View RelatedI have an issue where filtering my framing member schedules per Level by, for example, Level equals LEVEL 3 causes the entire schedule to be filtered to empty. We clearly have members constrained to and occuring on LEVEL 3.
The same happens when filtering for, say, at or above LEVEL 3, but interestingly not at or below LEVEL 3, in which case nothing happens -- that is, it still displays members clearly occuring only on and constrained to Reference LEVEL 5.
I'm just a novice when it comes to this program, a student in High school so I'm not very familiar with it.
Why is it that when I change one floor's surface (tile,carpet, ect.) and then make a seperate floor on the same floor but with a different surface, it changes BOTH floors like they are instances of each other?
How can I add a surface to individual floors on the same level? Ex. Carpet in living room, Tile in Bathroom.
I created an underground parking level but for some reason, I can't create a Space for it even though it has walls, a ceiling, and a floor.
View 1 Replies View RelatedI'm trying to create workset by view level , for example I need to assign each floor in the building to separated users and by that way I let more people shares in creating one revit model. I create worksets by views but I notice that I still can open any view level and I can add elements . Is there any way to lock the not editable views from opening and adding a new elements and make it secure ?
View 2 Replies View RelatedWhy are my Level Lines highlighted green?
Also why do some of the level symbols appear blue?
Searched and find, how to change the colors of the types, not why they are displaying in other colors than black.
Is it possible to show the exterior walls at a different detail level than the interior walls in the same view? Keep in mind they are all apart of the basic wall system family so there is no editing the family visibility at this point.
View 1 Replies View Related
