I am using vertical wall reveals for joints in concrete tilt-up panels. They work just fine until I need to dimensions to their centerlines. I tried using two 'half joints', but as soon as I align them I lose the option to snap to the side of the reveal in the center of the joint. The attached image shows both attempts. Is there a way to get this to work?
View 9 RepliesI need to model a wall in plan which has a section that is inset on one side. The inset having beveled faces. I have achieved this using a vertical wall reveal with a profile to suit the shape of the inset. This works very well until I place a door in the centre of the wall where the reveal has reduced its width, the reveal disappearing and the door appearing in a full width wall.
Does this mean that a reveal cannot be used in this way and that I should find another way of modelling the reduced width wall? See drawings below:
How do you control the line weights of wall reveals in 2011? The default is way to heavy for our need and I see no way to modify this.
View 3 Replies View RelatedI'm trying to Join First and Second Floor walls that are interrupted by floor framing. I've separated sheathing and siding layers and extended these over to the lower wall. All looks good, except for the joint line. In section view, I use Join Geometry tool and it works, the joint is gone. However on Elevation and 3D viiews the line is still there.
View 2 Replies View RelatedHow im going to make it just a single vertical frame in 45 degrees wall?
View 3 Replies View RelatedAt Home>Opening tab>Wall in Revit 2012 I cut an opening in a brick rainscreen wall and the brick coursing turned vertical at the wraps.
View 1 Replies View RelatedI am trying to create a custom curtain wall which will contain vertical strapping for the vertical mullions and horizontal wood boards. I created the two profiles and am able to create the curtain wall type control spacing etc...This looks great in elevation and plan, but when I cut a section detail the vertical strapping is cut at every horizontal mullion.
My question in short! If I want to create the look of continuous horizontal boards how can I prevent the vertical mullions from being cut? I'd rather not offset them apart so I can use this model element in details. See the section detail view attached.
Is it possible to put Reveals in concrete columns?
View 3 Replies View RelatedI created a curved, sloped wall (it's actually a tower) using in place mass, model by face - wall. I need to place reveals in the wall to simulate ACM panels. I've tried using the reveal tool in the wall drop down but it won't allow a reveal to be placed in the custom wall.
View 4 Replies View RelatedAny way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedWhat's the best way to create the attached: EQ ashlar panels, and wall sweeps with joints?
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
1. IS there a way to take a 10ft 2.5inch by 7ft picture and cut it up into 3inch by 12inch and have all of those save as output?
2. My second question is if I can also save it to a file with white background with .5inch margins on the left and right (so its a 4x12 inch image)
I intend to make a wall poster on my venetian blinds and ill fold the .5inch margins over and tape them to the back of the blind.
I have a problem inserting the slanted columns when I use the "Beam/Column joints" commando. When I insert the slanted column, the beams are divided.
It should look like picture 1, but it always ends up as image 2. How can I solve this?
My problem is trying to move the project model to a new elevation some 1000+ feet higher than the 0'0" schematic design elevation. When using the "shared" solution, it will work for the model but not for the Topo as the topo is also tied to the Project base point, so when one uses shared it also moves the topo map 1000+ feet higher. I'm trying to find a way where the project elevation can be adjusted to the base point elevation so both topo and model elevations coordinate with each other. It's a 4 level project with many exterior retaining wall levels. I'm almost to the point of doing a full copy of the project to the clipboard and then importing it at the level 1000+ feet higher.
View 1 Replies View RelatedAlright, I made a custom bookshelf to fit under my stairs, however, when I created them, I made them on a horizontal plane, so when I loaded into my project, my book shelf is laying down in the middle of the living room floor, which was fun at first, but nearly an hour later I am not so amused. Is there a way to flip it vertically or do I have to remake the whole bookshelf?
View 4 Replies View RelatedHow can i get horizontal mullions to cut through vertical instead or reverse?
View 2 Replies View RelatedI've created a non-symmetrical curtain wall mullion profile. When I assign that profile to a vertical curtain grid line, it is flipped in the project. In the attached image, you can see that the brace on the right in the family plan view is on the left in the project plan view.
View 9 Replies View RelatedI'm trying to create a 3 digit grid bubble that will align vertically along an elevation, but my grid bubble in use within the project insists on the text being horizontal... Is there any way to force the alignment to vertical...?
View 2 Replies View RelatedIs there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View RelatedShort story is I made a wall sconce from scratch but I can't see the symbolic lines in my ceiling plan in the project.
I needed a linear wall sconce for a client presentation based on one of theirs already installed. The manufacturer doesn't provide BIM for this model so I had make my own. I haven't bothered with photometrics. At this point all I need is a placeholder for the ceiling plan and a 3D model for a hidden line view. I used the wall based light fixture family. There was a plane elevation but no apparent parameter so created one and called it 'mounting height'. After about ten minutes of modeling (and over an hour of tedious aligning, dimensioning and locking of the sketches to keep the model from distorting with changes in wall thickness) I opened the ceiling reference level plan and drew some symbolic lines to represent the fixture on the ceiling plan in my project.
Here's what happened.
The symbolic lines for the CPRL (Ceiling plan in the family editor) are also visible in the FPRL. I don't know why this is and there doesn't appear to be a way to hide them in just one plan. I suspect it's because both are at the same height (the reference level.) I tried changing the working plane before drawing the symbol lines to another plane above the reference level and out of its view range but it had no effect. I can still see them in the floor plan.When I loaded it into the project nothing appeared and I got the message about 'no elements are visible because yada yada'. The symbolic lines didn't show up at all. I checked the detail level and that wasn't it. As far as I can tell the view range for the CPRL and the RCP in my project are the same. They don't show up in the project floor plan either. The sconce is visible in 3D views so it's definitely in there. I tried monkeying with the height of the symbolic lines like I stated in part 1. but it had no effect on there visibility. Symbol lines are visible in other families so it can't be an issue with visibility overides.In my project I noticed there's a parameter for the fixture called 'Elevation'. Changing it moved the fixture up and down on the wall. Changing the 'mounting height' parameter in the project had no effect! This parameter worked fine in the family editor. Playing with the 'Elevation' parameter and the cut plane elevation brought the symbolic lines into view. Apparently the symbolic lines are only visible when the cut line is passing through the sconce. Unfortunately my sconce needs to be mounted at 6 ft and my cut plane is at 7'2 to avoid cutting doors and windows. How do get these symbolic lines to display?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I want to turn off a metal stud wall but leave visible the pre-cast wall.
View 5 Replies View Relatedrevit should give a sub category for wall so it easy to on and off using visibility and give different line color in the object style
View 2 Replies View RelatedI am using revit LT 2014 and just can't get a material to be be painted on a wall. I would like to apply a 6" veritcal line pattern to look like v-groove board - I create the material, applied the pattern, but when I use the paint function I get nothing
View 1 Replies View RelatedIs it possible to edit a Revit schedule template? We need the schedule to be vertical not horizontal.
View 4 Replies View Related