I am trying to create a custom planter based off some line work that I did in my project. It has a curve. basically what I have done is created the line work on plan but now I want to use that curved line to create my family. which I am thinking I can create a profile and then sweep it on those lines. The problem is I can get the line work to the family.
View 2 RepliesIs there a way to load, for example, a wall created in a different project, into another project?
View 1 Replies View RelatedIm try to crop .rft format but i cant crop my family model in project file. Then how to explode family in project file.
View 9 Replies View RelatedI am trying to do the travel distance plan for fire cert saftey plan (Ireland). I have 6 levels of plan. When I place a component of "travel distance" family symbol (that I created) on the top floor plan, it is showing on the ground floor plan but not inbetween (TG).
See attach.
When I try to add a window or door, I get a message: "No doors family is loaded in the project..etc etc" and then I try to go and find a default template file to use which I assume has basic families loaded, I can't find any anywhere. I'm stuck at step 1, already.
View 6 Replies View RelatedI'm trying to make a project-file for a table that I've made as a family. In the project file I want to dimension the table, as a whole and as the differents parts of the table.
I've made visibility parameters in the family, but my problem is that that will hide that part of the table, i.e. the legs, in all views. I want to have one section with only the table top, one section with only the legs etc.
how I would go about this without copying the table in the project file and hiding different parts in each of them?
Is it possible by importing a drafting view or copying 2D details, to not duplicate the detail components families ? I tried many ways, but I always get my families duplicated.
Copying 'Gypsum' will always duplicate with 'Gypsum1', even if they are exacly the same original family.
Can revit have duplicate family names. or family names are unique in a project.
View 1 Replies View RelatedI have a very simple 'Metric Generic Model line based' family that contains 1 rectangular extrusion.
My Problem: Revit wont allow me to place a FamilyInstance of this family inside a (Architectural) project. When I click Architecture Tab->Component->Place a Component and select my Family I get a circle with a cross in it and are not able to place my family instance anywhere. Note this occurs in all levels/views from Site to Level 1, 2 etc.
why I can place it in a project?
Made a family with two family types, a red and a blue. when i load it into my project it comes up gray..Another component family the color comes in fine
View 1 Replies View RelatedI've created a Title Block Family and when I bring it into the project I want to be able to edit the text on the project without having to go into the Family and edit it from there, how do I do this?
View 2 Replies View RelatedI downloaded a grab bar family that I thought looked very good. But then I tried to place it on the toilet stall portion (I also downloaded stall partition families). When I tried to place the grab bar, it wouldn't place -- I believe because the grab bar is WALL BASED.
So now the question is how do I go about placing a grab bar (or anything else) that is not wall based so that I can use it with the stall portion? I had tried to use face based but couldn't get that too work.
I want to Create a Wall Nitch that will be in a tiled shower we are doing. Best way to create a family that cuts into a wall? I don't want to Create an opening, because I don't want it going all the way through the wall.
View 4 Replies View RelatedI would like to create a family component using the wall foundation bearing footing as a template. I cannot find the file where the templates are located. I tried using the structural footing template but it would not give me the same flexibility the wall foundation bearing footing template does.
View 2 Replies View RelatedHow to create a adjustable_angle Bi-fold door family.
View 4 Replies View RelatedI am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies View RelatedIf I can create a Diagram for my project like this diagram? For circulation and sold & void spaces ...etc?
View 2 Replies View RelatedI'm trying to align a nested family to a reference line in my host family so that it rotates around a certain point.
I've created the reference line in my host family, locked the end point to two reference planes and then gave an angular parameter to the angle between the ref. line and the ref. plane.
I then inserted the nested family and aligned it to the ref. line. The problem is that when I flex the angle, i get a "Constraints not satisfied" error..
What could be wrong?
I'm using a generic face based family for both host and nested families...
Using Building Design Suite Ultimate 2014
I used railing tools and created railing in the project files. i want to change rail and Baluster.i created metric baluster and rail from family and saved in the local drive. i used in to my project also it is working fine.
i want to use this railing to some other project. how to get it either copy past or revit link or any other way because the railing created in project file.
In Revit 2013 I attempt to load an item from the Family but I find that the “Load Family” dialog box does not appear. how to get it to cooperate? Even starting a new project the load family dialog box does not appear. I have done: 1) system restore, 2 ) repaired install, 3 ) re-installed, 4) uninstalled and reinstalled from scratch but still the problems persists on this machine. all other office PC’s with Revit 2013 behave.
View 2 Replies View RelatedI've attached a simple RVT file with a family inserted and the front view active. I need to rotate the family 90 degrees but Revit reports the following error:
"Can't draw because Work Plane is at a very sharp angle in this view. Go to another view or redefine the Work Plane."
I have several window types in my project. Let's say that the window is 3'-0" wide by 4'-8" high - Mark #1. I want to group three of these windows and schedule the group as Mark #2 - not three separate #1 windows. How do I set up the three windows together to become a single window schedulable for the entire opening of the three windows grouped together so that the opening would read 9'-0" wide?
View 6 Replies View RelatedI would like to create family type with drop down list as shown in the image.
How it is created and for what?
Recently, My revit does not load families. The process I use is the following:
In the Build area of the home ribbon, I select the Component button. I going to the Place component ribbon. When I select Load Family form the Mode portion of the ribbon, the properties box pops up. It is locked at this point and I cannot do anything but hit escape. The program functions just fine in all other aspects. I have used a vanilla project to see if the project I am working on is corrupted and I get the same results.
I'm trying to edit the keynote family with no luck. We are updating our standards and getting into using the keynote system in revit. I have added the correct keynote to most of our standard materials and its working great. I then opened the keynote family and changed the justification of the text to justify the way we do notes. I also changed the line style of the leader lines so it matches our other notes.
All went well. I get stuck when I try to change the gap between the leader tail and the text. I can't find anywhere to actually edit the line/arrow in the family that would let me change how that works. If you see my attached image the one on the top is our standard note and the other two are the keynote family.
How to set / change that gap?
I'm trying to create a frame and panel kitchen cabinet door family. It flexes correctly horizontally, but I can't get it to flex vertically. What do I need to correct?
View 2 Replies View RelatedIs it possible to create the Wall family in revit?
View 5 Replies View RelatedRemoving tag leader, I couldn’t know how to remove the leader of the tag from its family. How this might be done?
View 5 Replies View RelatedThis includes door opening/cased and opening-elliptical art. When I put them into my drawing they show up in the preview but do not insert into my drawing.
View 2 Replies View RelatedI know I must just be missing this somewhere, but I would like to shut off the geometry inside a family that's associated with a specific parameter. This is while I'm editing the family.
Specifically, the family I'm creating is for an appliance that has the option of an arched, or rectangular opening. Once I associate the geometry for the arched opening with a parameter, I'd like to shut that off, so that I can create the rectangular opening. Similar to how the family behaves once it's brought into a project.
Right now, I'm just kind of using the temporary hide functionality to shut them off, but if I turn them on, then have to go back to make edits, I have to select the individual geometry all over again to hide it. I've also noticed that some geometry, even when hidden, can still be selected.
As Revit insert a door it cuts the wall starting at the flooring level upward door height but in real building the door openning starts from the top concrete
Can I tell revit to start cutting the wall bellow flooring (leaving the door wing to start from flooring) or how can i add this feature to door family...i would like to control the height of the cut below flooring (e.g be a parametric).