Lightroom :: Why Print Will Not Print Full Image
Mar 14, 2014
Was printing 4x6" from LR 5.3 fine. To an Epson 3880. Then went to Page Settings (MAC) changed paper size to 8.5x11". The preview responded with a larger page. I scaled the image up to 8x10 via lightroom cell size. But when I printed to the Letter size paper, LR printed only a close to 4x6" top left corner. This was not a full image like the 4x6. It was just a corner.
Exported to PS and printed fine.Can not figure why the print will not print the full image?
View 1 Replies
ADVERTISEMENT
May 10, 2009
i have made a poster in photoshop. when i created it i selected A4 but when i print it i am loosing alot of the image all around the border especially at the bottom.
what should i do to make it print from corner to corner and everything that i had on the page?
View 1 Replies
View Related
Nov 25, 2012
In LR4 print module the print and print one tabs are greyed out and I can't reset.
View 1 Replies
View Related
Apr 10, 2008
Is it possible to designate a full bleed print or a smaller bottom margin than .56in in the print module. How?
View 4 Replies
View Related
Oct 1, 2012
I've been trying to print full bleed images to 3880 epson printer from LR 4.1 and for some reason won't let me make 8.5 x11 borderless prints to printer. both the left and right side of image has white borders and top and bottom has none.
both page grids sides go as low as 1 and cell size reads properly of 11.00in x 8.50in. but when you look at image in print mode in LR- it shows white borders on both sides of picture.
been on phone for 3 hrs with adobe and 30 min with epson tech to no avail?
View 13 Replies
View Related
Nov 1, 2013
I wanted to create an A4 borderless print in my canon mg6150 from within the print module. I can do a borderless print using the canon easyprint.
I go into page setup and the properties of my printer and set the page layout to borderless and click OK.
However, I am unable to set the margins to zero. When I go back into my page setup and check the page layout, it has reverted to normal so it has ignored my setting.
View 2 Replies
View Related
Jan 7, 2014
All was working OK and the printer is showing ink cartridges almost full In the Library Module the print review is fine.
Switch to Print Module and the print review is now blank (100% white)
Pictures no longer print
Windows 7
Espon Artisan 835 printer
LR5.3
View 1 Replies
View Related
Feb 28, 2014
I have just bought and installed Lightroom 5 and need to set my print size to A3 and in the future even bigger. I do not have the facility at home and need to have them sized correctly for the print shop so they do not have to waste time resizing them. I am at a loss how to do this. I cant find any settings for this size print. A3 is roughly 42 x 29.7 cm.
View 2 Replies
View Related
Apr 1, 2012
I cannot seem to reset the print template screen while in the " Print " module. It has adopted the smallest pic size with three times the normal border. I wish to reset to full screen in print module
View 1 Replies
View Related
Oct 14, 2012
How to ADD (almost) white Border around photo(s) to print in print module (not for creating a JPEG) WITHOUT TRIMMING the photo?
I dont understand why I'm so stupid not to be able to acheeve this simple task with Lightroom WITHOUT TRIMMING the image (altering it's proportion and cutting away photo-content)
(on light-gray backgrownd for instance, to use as cutting indications. I know how to use cutting-indications for images i print without a border)
(i do not whant to use workarounds, the kind of preparing "identity plates", a new one each for infinite variations of proportions to use as fullblown-up backgrounds..)
View 1 Replies
View Related
Oct 13, 2012
How do I get my photos printed? I select a photo but I get the maessage that no photo was selected.
View 2 Replies
View Related
Sep 26, 2012
Epson 3880.
Lightroom 4.
Moutain Lion.
All current.
I am trying to print on 5x7 paper. I set the page setup to 5x7. I have the margins set to .2" on each side. The layout image inside Lr looks exactly how I want it to.Then I print. I end up with a .125" margin on the left and top, and a .625" margin on the right and bottom.
View 6 Replies
View Related
Apr 13, 2012
It seems that, no matter how many times i save and update the profile, all the print setting (image size, sharpening, bit depth, color management, ...) are store within the preset, all but the Epson Driver settings, which have to be selected every single time.
I really can't remember if this bug was present in 4.0 or not (I'm currently running 4.1 RC), but I'm quite sure it was working OK under 3.x. Here's the thing.
I configure the printing settings and create. a profile: Profile1.I change all the settings and create a second profile: Profile2. The "Print Settings" settings are different, same printer, one for Color (Profile1), one for Advanced B&W (Profile2).I click on Profile1 (which was created with color Print Settings). Clicking on "Print Settings" or "Print", the printer settings selected under the epson driver is the ABW one (the one that belongs to Profile2).I reselect the correct setting from "Print Settings..." (Color).Click "Save" again.Righ-t click on Profile1 -> Update with current Settings. Setting seems to be saved.I then click on Profile2 and bam! The "Print Settings..." seems to be rverted to color instead of ABW.Update the correct settings, back to point #3
Can you reproduce this? This behavior is vanishig the power of the "Print One" button, unless you constantly print with tha same Driver settings.
---
Lightroom version: 4.1 RC [820174]
Version: 10.7 [3]
Application architecture: x64
Physical processor count: 4
Processor speed: 2,4 GHz
Built-in memory: 8192,0 MB
Real memory available to Lightroom: 8192,0 MB
Real memory used by Lightroom: 2388,3 MB (29,1%)
Virtual memory used by Lightroom: 4759,6 MB
Memory cache size: 866,7 MB
Displays: 1) 2560x1440, 2) 1680x1050
---
Epson R3000, latest OS X Epson Drivers.
View 2 Replies
View Related
Jun 6, 2009
How do I batch print several exposures at one time that differ in orientation (Landscape, Portrait) or print size (4X6 - 8 X10) or both orientation and print size? I currently have Lightroom 2.3 installed on a XP SP3 machine.
I have been unable to find any documentation on this subject.
View 2 Replies
View Related
Mar 13, 2013
My "Print One" button in the Print Module of LR3 is not activated. What is amiss and how do I reactivate the button?
View 1 Replies
View Related
Feb 11, 2013
I set up a print package in lightroom v4.1 and adjusted the image in the cell to fit properly, however when I try to print to file the resulting file moves the crop to cut off the top of my subject's head. It seems that I can get around this by intentionally moving the image so that it appears to cut off her head, then when it prints it looks correct (the adjustments im doing are moving backwards?). This works for now but I have no specific control over my crop, I just have to guess and check which does not work for large quantities of images
View 1 Replies
View Related
Jun 29, 2013
I am trying to print a 16" x 20" photo through Lightroom's print module. I am using an Epson 3880 printer and 17" x 22" paper. I have done this in Lightroom 4 with no problems. Now I am getting a print that is 16-3/8" x 20-1/2". I have the cell size set at 16" x 20" and borderless printing is turned off. I also checked zoomed to fill. This has also happened on a couple of 12" x 18" photos.
View 2 Replies
View Related
Nov 1, 2012
I get a pop up of "Save Files To Folder", but no file names are present, so "save" does nothing. I have all the boxes checked in Print Job, e.g. print to Jpeg file. I have searched, re-read Kelby etc. and come up blank. I have a profile entered for a custom lab.
View 1 Replies
View Related
Aug 23, 2005
iv'e just created a montage of photos for a portfolio project im working on and now its time to print the montage.
I need to print the page so it fills the A4 or maybe slightly have a 5ml whit border all abpund,
View 5 Replies
View Related
Jun 27, 2012
I am using lightroom 3.6 and I would like to know how to print an image at 100% of it's size for a given resolution. In other words without any ipscaling or interpolation.
View 8 Replies
View Related
Mar 6, 2013
in dummy terms, how to crop a image for print. If I have a image that I have cropped, and I want to print a 4X6 and a 8X10, how do I crop it so parts of the edges do not get cut off?
View 4 Replies
View Related
May 3, 2012
Could be handy to set print "File Name" to image name.
View 1 Replies
View Related
Mar 14, 2013
I have a document which is sized for full bleed printing. I would also like to make PDF prints of this document, but if I simply print, then everything will be off by a little. Is there a non-destructive way to 'crop' the document back to the paper size?
View 4 Replies
View Related
Dec 6, 2012
A few weeks ago I tried to print from the print module and instead of a picture showing up, there was a white space. I have uninstalled and reinstalled LR 3 times.
View 2 Replies
View Related
Dec 27, 2011
When I try to print a JPG from the Print module in LR 3.6 (and tried it also with 3.5), it does not always recognize the resolution settings. Most of the time (and I can't see what makes the difference) it prints the JPG to a 96 ppi resolution regardless of what setting I use for resolution.
View 6 Replies
View Related
Jul 24, 2013
I tweaked an image in Develop and printed some 5x7s until I got it right and then went to 13x19 (first time ever using that size with my R3000). The print preview and the print were way too red. I went back to a 5x7 and it was way red as well in print preview, so I didn't print. I replaced a light magenta cart that I think ran out during the 13x19 print, and then some others that were low, and did a nozzle check and that was okay. I have spent hours looking around all of the settings (sRGB) and can find nothing that would explain what changed between my last good 5x7 print and the red 13x19. I went back to earlier versions and had the same problem. Monitor is due for recalibration, but that probably has nothing to do with it since it changed so suddenly.
R3000, LR 4.3, Win 7, NEC PA 271w
View 4 Replies
View Related
Aug 4, 2012
I have resized the image in Photoshop CS5 using Perfect Resize. The image dimensions are 20.00 inches x 13.33 inches. In the Lightroom print module, I chose these settings: cell size to 20.00 in x 13.33 in. All the margins are set to 0.00. "Zoom to Fill" is not checked.Page Setup: 17 x 22 paper. Manual - rear-borderless (retain size) .The size printed is 20.5 in x 13.75 in..What should I be doing to get the print size to match the cell size of 20.00 x 13.33?
View 8 Replies
View Related
Apr 11, 2012
Can LR 4 display the image (document) size in inches? The only metadate I can locate provides this in pixels, My current solution is to open in Photoshop then to Image-Image size-document size. .
View 2 Replies
View Related
Sep 12, 2012
In PS CS4 Mac, I used to be able to print the full document info that appears in the title bar, including the currently selected layer/group. This would print at the top of my document and might look like:
File Name.psd 100% (layer name, RGB/8)
I always thought this was a function of selecting "Label" in the Output window of the print dialogue box. However, it does not seem to be working anymore, and now it simply prints the file name, like this:
File Name.psd
How can I turn this feature back on so that I get the entire document window? Or another method to accomplish something similar? I am printing individual layers from a single document and having them automatically "labeled" is useful.
Mac OS 10.6.8
PS CS4
View 3 Replies
View Related
Dec 22, 2012
I'm using pse10 on a computer with an i7 processor with 12GB of ram and windows 7 with a color laser printer. The print function works fine while in organizer and sharing mode, but not from full edit. When I try to print from full edit, I get an error message with a red "X" on it that says: "Before you can perform printer related tasks such as page setup or printing a document, you need to install a printer." I can't figure it out. The printer is in "ready" state, and works fine in the organizer mode, and in share.
View 2 Replies
View Related
Mar 27, 2012
When I construct a multi image contact sheet and send it to my printer the file is aborted. Mac Pro, 15 GB ram, OSX 10.6.8, Epson 7890. LR4.
View 2 Replies
View Related
