Lightroom :: Slight Bluish Tinge On Print Margins?
Dec 14, 2012
I built 3 profiles with ColorMunki for three different papers (I print with an Epson 3880). Using each of the profiles, a slight bluish tinge appears in what I'll call the "margin" of the prints. My tests were done on 4x6 paper, but the image was only about 5" wide--so there's a 1/2 inch "margin" between the edge of the image and the edge of the paper. The bluish tinge shows up here, but doesn't extend into the white border of the print. The weird part: the bluish tinge appears ONLY using the profiles. If I choose "Managed by Printer" everything is fine. No bluish tinge.
Â
This could be related to LR 4.3, which I downloaded just before making and installing the profiles.Â
View 2 Replies
ADVERTISEMENT
Feb 10, 2014
I want to print a photo in 5x7in.I have a Epson Stylus Photo PX710W printer. I select it from Page Setup button.Then i select the paper size as 5x7in (13x18cm)
Â
But i couldnt set the margins in same size.Left, right and top can be set as 2,8mm. minimum but bottom can set to 3,2mm.Zoom to fill and rotate to fitt both are selected.
Â
Cell size is: 121,0mm. maximum size.
Cell widht is: 172,1mm. maximum size.
Â
I uninstalled my Printer's drivers and software and reinstalled it, but nothing has changed.Then i reinstalled Lightroom but no changes.I use the latest Lightroom 5.3
View 2 Replies
View Related
May 17, 2012
I printed a few photos with the print function in lightroom 3 (print button). A few hours later, i reopened LR to print some more photos, and now the print button has been replaced with print to file. Print one button is all greyed out aswell.
Also, LR is adding unwanted margins to all photos in the print module, and when i try to 0 out the margin, LR tells me it needs a minimum margin...
All printer settings is as it was before.
Â
What has happened?
Â
I have been around all preferences and so on, but nothing changes.
View 4 Replies
View Related
Oct 29, 2002
I try to print images at work for my boss, the images come out aligned to two sides of the paper (ie the top and left), and not centered... even when the "center image" option, etc.. are clicked..
I have tried to "change margins" but those areas are greyed out and uneditable...
View 2 Replies
View Related
Dec 19, 2007
I have set up an A3 size print style (420x297mm) with 5mm margins all around. i am plotting a drawing to its extents (400x277mm) which should leave 5mm between the drawing extents and the page margins. when i preview the page it looks perfect. however when i open the created .pdf the result is somewhat different. the spacing left to right is spot on but vertically the drawing is off the top of the page approximatly 15mm. i have tried many things to try centre the page but the closest i can get it is a 13mm margin at the bottom and 2mm margin at the top, achieved by unchecking the centre the plot box and inputting 0 for the y offset.
View 9 Replies
View Related
Jan 4, 2013
How do I select to print a document without margins?
View 3 Replies
View Related
Feb 21, 2013
I have a layout with a border that is alligned very well in the layout view (see attachement 1) but the whole thing somehow moves to the left when I preview the plot (attachement 2). I thought the dashed lines were supposed to indicate my printer's plot area. Is there a way to fix this anomanly? I have tried to play with page setup options, application options, but nothing works.
View 4 Replies
View Related
Aug 8, 2011
Ever since updating our print server to use the HP Universal driver, my ability to tweak the non-printable margins has gone away. In the past I was always able to easily tweak margins within my PC3 files using the "Modify Standard Paper Sizes (Printable Area)" tool. Setting all four values to say "0.25" would result in an even 1/4" margin around all four edges of the paper.
Now however, that behavior is just plain different. Using 0.25 all the way around results in plots that are partially shifted off the page. Using different values for top, bottom, left and right results in one or two margins coming out much wider than I want. The frustrating part is there seems to be no rhyme or reason between these values and the plot output. The default values are 0.17 for Top/Bottom and 0.25 for Left/Right but even this results in uneven margins. Only if I make the slightest of tweaks can I get any tiny bit of improvement, which is still not up to previous standards. Anything larger and the output is much worse. I've tried all 0.0, setting top/bot only. left/right only, but none of my combinations of values works.
On top of that there seems to be inconsistency between each printer, even when the printer Model is the same. For example the output on my 9050DN printers range from just "Decent but not like before" to plain "awful". My older 8150 DN models look the best but still do not match previous output. Â
Is there an alternative way to adjust paper margins? Is there a new method to adjusting the "Modify Standard Paper Sizes (Printable Area)" ?
View 2 Replies
View Related
Jan 18, 2013
Is there a way to apply a slight boost in exposure to multiple images that have different exposure settings?
View 2 Replies
View Related
Feb 20, 2014
I'm printing from Lightroom and Photoshop (Creative Cloud) and consistently getting images off center (top to bottom). The layout in the LR print module is set to 1" margins on all four sides, but there is only a very narrow margin appearing on the top of the print. How do I get the margins to be uniform?
View 1 Replies
View Related
Mar 1, 2013
I have been shooting RAW for a while and have notice that after I import the images and then start to view them in the Library Module I will see a slight color and quality shift - almost looks like a white balance shift but not quite.  I was thinking that perhaps there was some automatic preset being applied but I don't have any presets at all.
Â
I am shooting with a Canon 1DX as well as 7D. I have not checked to see if I get this situation with the 7D, but I know for sure that I get it with the 1DX.
Â
Today I was reviewing some images in Bridge and decided to open one of them in Camera RAW.  At that time I discovered that the camera's Image Style Settings were available, Faithful, Standard, Portrait, etc. I noticed that the images did not have one of the camera styles applied to them but rather the Adobe Standard Style. At that point from within RAW I selected one of the camera's styles and bingo thats the kind of shift I am seeing when I first view an image in LR4 Library.
Â
So as far as I can tell the RAW images are getting the Adobe Standard style applied in LR.  I have no idea if this is a default behavior of if I have done something to cause it. I'm also thinking that perhaps LR does not necessarily apply the Camera's Styles automatically even though the particular style has been set in the camera -- perhaps is not imported as part of the metadata during the import and thus defaults to the Adobe Standard.
Â
1. Should I expect LR4 to apply the Style as set from the camera automatically or not at all?
2. Can I prevent LR from applying the Adobe Standard Style and apply no style?
3. Can I cause LR to apply the Style as set in the camera for the particular image to be appied automatically upon import?
View 3 Replies
View Related
Feb 1, 2013
I downloaded the trial version of Lightroom 4 onto my Macbook pro and when I try to use the adjustment brush the cursor that normally turns to a brush when you hover any part of the photograph only changes at the very edges of the picture. When I move the cursor towards the center of the photo the cursor changes back to an arrow and I cannot make any adjustments. If I start an adjustment at the edge of the photo I can drag it into the center of it, but I cannot release and then do any further painting in that region. At the point where the brush icon changes the cursor becomes a small arrow that points to the edge of the frame and if I hold down the left mouse button and move to the transition line it becomes a double facing arrow, I can then drag the area I can work in to make it even smaller, but I cannot increase the area.
View 1 Replies
View Related
Jun 25, 2012
How can I get multiple images on 1 page to line up when printing on both sides? Dimensions are 3.5x2.5, 9 to a page. They are sportscards for son's baseball team. They are slightly off by 2-3 cm on all 4 sides and in betweeen. Extremely frustrating. I tried printing in Photoshops but text is blurry. In Lightroom, Images look absolutely perfect. If they would only line up. Using a Canon MG 6200 if that matters.
View 7 Replies
View Related
Jun 29, 2009
I have PhotoShop CS3 and EVERY picture I open in PS is yellowed...I open then in MS Paint and they're fine, same as IE, FF, and default photo viewer. What is wrong with it? Just did a fresh install.
View 27 Replies
View Related
Apr 3, 2012
Every image I open in Photoshop has a purple tinge to them. I think this must be a setting I have in the program. I can't even print screen it as when I do, it comes out in the correct colors. It doesn't do this in any other programs (indesign, illustrator etc)
View 1 Replies
View Related
May 1, 2009
When I open one particular image in photoshop CS3 the thumb in the Open menu looks correct, but the image opens with a reddish tinge over the whole thing. If I then double-click the image layer in the Layers window, the Layer Style menu pops up, the tinge removes itself and the image looks as it should. None of the other images I've been working on have this happening. Does anyone know what's up here. This is a .psd file with no layers above the image layer.
View 4 Replies
View Related
Jun 18, 2012
How to create this background effect, the bluish bar that is under the text?
[URL].......
View 1 Replies
View Related
Mar 9, 2012
i've been trying since my filesystem died, to get this right, basically, i'm trying to get the blueish industrial effect of the skull, shadows and all. and if at all possible the blue glow thing in the top right of it as well, I'm about to reinstall ubuntu and Photoshop it'll be ready for tomorrow.
here's the image:
View 8 Replies
View Related
Aug 4, 2012
I just bought a MacBook Pro three weeks ago. I'm running Mountain Lion. Also, I have my copy of Adobe Photoshop CS6.
Â
Something very unusual is happening. I'm a Graphic Designer and currently doing an Interior Design major. I calibrated my monitor perfectly. But now, ever since I installed CS6, every time I open Photoshop, a bluish tint sets on the screen, affecting every program running (browsers, for example) and it's very annoying (not to mention it disrupts any color calibration I made to my monitor). The only solution to this problem is closing Photoshop (the problem persists even if I minimize Photoshop to use another program).
Â
I tried opening Illustrator and it works fine. Only with Photoshop this is happening.
Â
I searched on Apple discussion boards for similar cases and found nothing.
Â
What's interesting, I took screenshots to send them to a friend and the screenshots don't seem to be affected by this phenomenon.
View 8 Replies
View Related
Jan 25, 2009
I'm running photoshop on my Asus eee pc but I have it running on an Acer Aspire 5670 monitor (bigger screen makes it easier for my retouching work!) and whenever I shutdown photoshop my screen gets a little bit bluer.
I can fix it by doing a recalibration but it's still kinda annoying because I don't always remember to do it and I'm sure you can understand that trying to get skin tones right when your screen is blue can be an utter.
View 39 Replies
View Related
Nov 25, 2012
In LR4 print module the print and print one tabs are greyed out and I can't reset.
View 1 Replies
View Related
Jun 3, 2012
I have 8 gig of ram and a nvidia NX8600Gt vid card - never had problems in CS5.5 and expected CS6 to be better, but it is not.Â
View 1 Replies
View Related
Nov 19, 2008
Using Photoshop CS4 on Vista with a dell monitor.
I have the standard dell color profile set in windows for the monitor.
Whenever I save "for web and devices" I get a color difference between the actual webpage colour and the colours in the picture. So I searched about color profiles and I gather (I find this profiling thing very confusing) that I should set my photoshop profile also to the dell profile. So I did, but there now still is a slight difference.
For example, the color I use in photoshop is #12141A and once saved it shows up as #13151B
View 1 Replies
View Related
Jan 4, 2005
i have pictures due on the 7th this month. The only thing that bothers me in my picture is that I have a slight shadow out of my face (on my right). I have never used Ohotoshop so I dont know how to remove it. I have photoshop 7. I am attaching my pic and I would GREATLY appreciate if someone could list the steps i need to do to fix the picture. My girlfriend's picture is the same .. so Ill need to know the steps
Also if I could maybe lighten up the background ...
View 3 Replies
View Related
Nov 15, 2013
I have tried a number of different methods however I cannot seem to get rid of this problem. Every time I put together banners or any graphics/designs for that matter, whenever I save them and then display them I always end up with a slight blur. I am trying to get a really crisp finish but can never seem to get it right, please see attached photos .
View 3 Replies
View Related
Apr 15, 2005
I'm trying to save the image in Photoshop under Save for Web. However, the optimised images always have a slightly yellowish tint.
View 2 Replies
View Related
Jul 25, 2013
Today i've noticed that when i copy/paste a timeline from Premiere CC to AE CS6 unfortunately nothing happens. So i can't dynamic link or copy/paste footage in AE CS6. I can only use AE CC. Usually i make my edit in Premiere and then i use the same timeline in AE to do postproduction. If i uninstall AE CC can i be able to copy/paste my timeline in AE CS6 from Premiere CC?
I can't install Premiere CS6 because i use an MXO2 card.I can run AE,Photoshop and Encore CS6 with CC apps on the same machine,but not Premiere CC and Premiere CS6 at the same time.
View 2 Replies
View Related
Nov 1, 2013
I wanted to create an A4 borderless print in my canon mg6150 from within the print module. I can do a borderless print using the canon easyprint.
Â
I go into page setup and the properties of my printer and set the page layout to borderless and click OK.
Â
However, I am unable to set the margins to zero. When I go back into my page setup and check the page layout, it has reverted to normal so it has ignored my setting.
View 2 Replies
View Related
Jan 7, 2014
All was working OK and the printer is showing ink cartridges almost full In the Library Module the print review is fine.
Switch to Print Module and the print review is now blank (100% white)
Pictures no longer print
Windows 7
Espon Artisan 835 printer
LR5.3
View 1 Replies
View Related
Feb 28, 2014
I have just bought and installed Lightroom 5 and need to set my print size to A3 and in the future even bigger. I do not have the facility at home and need to have them sized correctly for the print shop so they do not have to waste time resizing them. I am at a loss how to do this. I cant find any settings for this size print. A3 is roughly 42 x 29.7 cm.
View 2 Replies
View Related
May 6, 2012
I had about twenty seconds to take this picture last night but only to notice it is rather dark due to the limited lighting in that area. I have tried various settings in Lightroom to brighten it up enough to see the moon and the building in the foreground but the pictures just come out to grainy and a slight purple look. what i can do for this?
View 5 Replies
View Related
