I am using Illustrator and I want to be able to select the arm or leg of a line drawing cartoon character and reposition it to create a new position without having to redraw the arm or leg.
I know you can do this in After Effects with the puppet tool. Is there a similar function in Illustrator?
Voorstel spantenlijn.dwg
I have created a dynamic block. Herein I placed stretch actions parameter set to strecht parts including anotative text.
Now the block seems to work fine.
- When I am in modelspace and I change the annotation scale the text is changed correct
- When I am in modelspace and I change the stretch value of the dynamic block everything goes fine.
But when I am in modelspace and I change the stretch value in one of the annotiaton scales and then switch to another scale my text is changed annotativly (this is what I want) but the stretch value is set back to default (which should be at the changed value).
I think stretch is the right word I'm looking for... I figured out how to outline the text, and I ungrouped the outline. However if I stretch the whole letter, the left "leg" of the 'R' goes down as well. I just want to stretch the right "leg" of the 'R' so that it reaches the bottom of the word Agency.
View 3 Replies View RelatedI'm looking for the best way to stretch the P in the word Postgraduate for a project.
The font is News705 BT.I need to make the P much longer and then extend it under the word - as in the image below.
I have a complex object (a plot with a bunch of text labels, etc.), and I want to stretch it horizontally or vertically without distorting text. I have an option to scale or not to scale strokes,. However, whatever I select here, the text always ends up distorted.
Is there a way to stretch it so that the text retains it's original shape?
My ai doc has a stretched font and when i subsequently added indepented words/phrases in different locations, they are all stretched as well. I only wanted the one stretch, so I will have to go in manually and will never get them exact, or just start fresh, so I wondered if there is a way to restore them to their original properties. Also is there a way to avoid what I did? It also stays in "stretch mode" when I typed in a different font, which is how I noticed because the o's are supposed to be almost a perfect circle and they were ovals, so it was obvious, although the first font wasn't to me.
View 2 Replies View RelatedWhen I stretch an object to the right using the right hand side handles, the left side of the object also moves slightly to the right. How can I stop this from happening and keep have the left side stay perfectly in place. Is there anything in the settings I can change?
View 4 Replies View RelatedAs you see in the picture I have merged a window modeled in 3ds max.
How is possible to make it higher, means strech it along the Y axis from the middle and up?
If I use "scale" as you see the width of the window becomes bigger (wrong) I tried to use "mesh edit" or "stretch modifier" with no good results...
My question is how to stretch this window the way I want without changing it's width...
I made a little video commercial, where I show album covers, with intermittent quick videos of me in- between. Since I changed locations where I DJ now, I took the original video, and just tweaked it a little with the new internet address, etc. The album covers I used were all originally 300x300, and I have them all centered in the overlay screen.
The problem is, when I play the video within VSx3, everything looks fine- but as I'm encoding into a .flv file to upload on youtube, it's distorting all the perfect "squares", and "rectangulizing" them the long way.
i'm doing a CD layout and want to use an image that stretches across all three of the front panels for the cover. the image in question, in it's original form is: 300dpi and roughly 5.75in x 3.8in. i need the image to be able to fit a 14.5in x 5in area (i realize the photo will need to be cropped).
so, how does one make the file larger while retaining the detail of it 300dpi? i've already imported the photo into InDesign and exported it as a PDF, opened the PDF in PS at 800dpi, then resized it with the RESAMPLE IMAGE box UNCHECKED and the pic is ultra grainy.
I'm having problems with some of the things on photoshop stretching the page. Today, I was trying to add a splatter effect (filter > brush stroke > splatter), and when I went to the page, the window was too big, so I couldn't see the settings on the far right. I'm not sure if it's just my computer's screen size. Here's a screenshot if you're confused.
View 4 Replies View RelatedI am using CS2 for creating web pages and Ive run across a little problem. I cant figure out how to "save for web" so that my *.jpg will be stretched across the web browser when people view it. When I view my *.html after "save for web" it places the *.jpg in the top left corner of the page. I can use Dreamweaver to center my image, but it still looks out of place. Ive seen photoshop created pages stretched to resize with the web browser window;
View 3 Replies View RelatedWe work on a double-monitor setup!
Is there a limit for how much you can strech a toolbar.
I keep all my toolbars on a dedicated screen, from the bottom of the screen to the top but they stop streching at about 1035pixels.
The screen has 1680px vertical. As you can see on the SCREEN-SHOT bellow there is a loot of space to strech them but they wont go beyond those 1035px.
Imagine you have a a box, say 1 foot square. You attach a fat rubber band in the center of one side and then you pull the rubber band up to an edge and around it to the center of the next face. It stretches and the corner is the only spot that controls the change of direction. If you raise one end (the segment from your finger to the corner) it raises, but the segment from the corner to where the other end is attached stays flat on the box until you move your hand far enough away so that there is now no wrap around the edge. Now if you pull and relax, it acts like any normal rubber band. But then if you lower your fingers with the end you are holding and go back down to the face, you wrap around that corner again and can pull and relax around the corner.
What I'm actually doing is animating a muscle that goes around a bone when it's stretched out. But when it's contracted, one end moves out away from that bone it's wrapped around and it's now just a straight line. I need to animate that muscle from that contracted and straight position to the extended position but have the end of the muscle bend around the bone when it hits it.
I have been trying to understand why does TurboSmooth or MeshSmooth modifier tend to stretch the UVs of the low poly unwrapped object. For example I have a simple box which I unwrap and smooth out with TS modifier after applying the map it stretches because the UVs get distorted by the TS modifier. check the image to get a visual idea of what I am talking about:
Uploaded with ImageShack.us
I use "Add: Pick Points" to hatch my elevations. The hatch does not seem to stretch when I need to stretch the elevations. Is there a way to make it stretch?
View 4 Replies View RelatedPrior to 2013 I have been able to stretch wipeouts - it seems that this command no longer works!! Is there system variable that needs to be altered? or have Autodesk simply removed the functionality??
View 9 Replies View Relatedhow to stretch text across page.
View 9 Replies View RelatedI have a picture that is slightly a rhombus. I would like to select the four corners using the polygon lasso tool, and would then like to paste it, but stretch the corners so it becomes a perfect square.
I have been trying this with the perspective, but am not having any luck.
I am using the Photoshop 6 for windows.
Simple problem: When I select a line, normally three grips appear; the ends and the middle. Normally, when I want to stretch (resize) a line I click one end and simply drag it to the desired location. Often it *snaps* to another nearby grip point, the middle selected grip, a line that it crosses, etc. If I zoom in I normally can put the grip any where I want to. It has worked fine up until this morning. Last night when I closed the program it worked perfectly...first thing this morning it doesn't work at all. Restarting the program and the computer had no effect.
The grip will only snap to the other origin (making it zero length) and other random points nearby. I cannot make it a random length...it must snap to those other points, and it *will not* snap to the middle point of the line, which I do all of the time.
Did I accidentally hit a CTRL+ or ALT+ key-stroke which has changed the abilities to snap?
In Revit, how can I stretch a building in one direction, including all floors, in either plan or elevation? Let's say a wing of a 3-story building is 20' long, and I want to make it 24' long.
In ACAD, there is the stretch command that uses a fence.
Granted I would have to use stretch on each plan & elevation drawing, but all elements within the fence are sretched.
Do I have to move a grid, and hope that I've locked all walls on all floors to that grid so they move when the grid is moved?
Any way to get the same squash and stretch (preserving volume) results using 3Ds Max CAT and the Skin Modifier. I heard that using an Expression Controller is one way of doing it but where to find documentation or tutorials on the process.
View 4 Replies View RelatedI'm trying to add dimension with the stretch actions.
View 9 Replies View RelatedI have a few horizontal lines parallel to each other. I'd like to make all of those horizontal lines longer by multiplying their length by a factor (let's say 2)
The scale command doesn't work as I intent, since it makes the spacing between those lines "x" times greater as well.
Which command should I use?
I'm looking to make a dynamic block that will either strech up or down but some of the element stay the same in the other visivility
Here is a block i am talking about!
dynamic block.dwg
I draw ventilation ductwork all day at work, just recently stumbled across dynamic blocks.
Attached is what i have done so far, the straight section works perfectly, just having some trouble with the radius bend. What I need is for the arc to stretch with the angle of the bend.
TEST.dwg
In 2k9 in 3d i used to be able to click on a box and then click on a grip and see the height or width...but now i can't see the dimensions how do i get those dimensions back?
View 3 Replies View RelatedI am looking for a method to stretch an image in a non homogeneous way. I am starting with a rectangular image that I want to stretch horizontaly to finally obtain a trapeze in the way that the bottom pixel line does'nt change, and the top one is three times bigger. In a certain way, I want to do a perspective but without the vertical rescaling.
View 18 Replies View RelatedI cant figure out how to stretch one side of an object .
View 11 Replies View RelatedI have been having an issue with my hatches, especially when I use solid. I always make them associative but when I have to move an object using stretch, the hatch does not come along with it.
When I hatch an item I generally use the "pick points" option. Do I need to be using select objects?
I have accidentally cut on some function in autocad that I can't figure out how to cut it off. Now when I select an object, it has a UCS icon (red arrow & green arrow) in the center of the object and you can stretch the object by using the arrow or the box in the middle.
View 6 Replies View Related