AutoCad :: Properties Line Equal But Appearance (print Preview And Printing) Different
May 2, 2011
The lines apear with different width, but they have the same properties (layers, pen , thickness etc...). AND THERE s NO supperposed lines. The only thing different is one have vertex z, and the other only x and y.
Have tried following solutions:
match properties,
flatten image (all z with 0),
repair archive with audit, regen
copies past theses line in a new archive,
print with different printers...
nothing change.
Something more strange there, when i draw line they are with x and y vertex. When i draw circle it have also z vertex, wich made another apprarence... .
I was playing around with my settings and did something that is keeping me from printing. When I go to print preview, the page is blank. I have tried opening up jobs that I successfully printed before and they also show and print blank. Everything looks normal in the work area. I just can't print.
I'm unable to get a print preview displayed prior to printing using PSE11 and a Epson Artisan 730 printer. I've ticked the print preview box but the print preview fails to appear and the printer prints the image straight away!
I am looking to draw my pipe with a thicker appearance than the typical line of width "0". Our storm pipes are usually drawn with this so as to stand out from other utilities. If the pipe is represented by a polyline, I have usually adjusted the "Width" or "Global Width" value to my liking. With pipe objects, it seems more complicated. I have searched the settings, and the closest thing that I could find was the Lineweight property, but that appears to have no effect on the line thickness in the CAD drawing.
Do I need to tweak a plot setting? Make a new linetype altogether?
I have a line that i would ideally like to divide into 3 equal segments. The divide command places points along the line, but I can't snap to them.
I know that I can place a block at each point which I could snap to, but is there a way of doing it without creating a block? Also is there a command that actually splits a line into 3 equal-length lines?
Just passing along this preview "glitch" in CS5 that could cause some headaches or costly reprints.
We had a file where some text "appeared"on screen as a solid fill even though it was mistakenly filled with a gradient in the colour panel.
When the job was output the type was missing.
Upon investigation it was noted the text was filled with a gradient through the color panel....however the preview did not reflect this. The proper way to apply a gradient to text is in the appearance panel> add new fill>gradient.
This will preview the gradient in the text properly. Shouldn't there be an friendly error message or pop up to warn users that this fill option is not available?
I received an Autocad file from another person, opened it with Autocad 2011 LT, and it looks fine. But when I go to print preview all the lines are very thick, making the detail of the drawing difficult to see. I've tried manually changing the lineweights but it has no effect on some of the layers. Is there an easier way to fix this other than recreating layers?
I use many types of lines for drafting. I have to set a Linetype Scale depending on the scale asked by the client. For example if the client asks for 1:100 then my lines are set to 0.5. But if he suddenly changes her/his mind and asks for a 1:250 scale I have to change all the Linetype Scales to 2.5.
Is there something like "Annotation scale" for lines? So whenever I change the drawings scale my lines can be seen as they must be.
How can I divide a line into equal segments in Illustrator? This is computer software, right? Shouldn't a computer be able to figure how to segment an arbitrary line? I tried turning the line into a sliced object and dividing that, but it didn't seem to work. Pathfinder only works on two or more objects.
I need to create a 100 wedges 'spinning wheel' graphic (like a pie chart but does not require pie chart functionality) with each wedge of equal size and spacing but can't seem to find a process that works.
When printing in 3d with the vp set to 3dhidden and the shade plot set to hidden legacy some solid items print with the wire frame. This usualy happens with torus and cones. How do I stop this?
So I am working on this document and it has silver background. I go to print preview (Photoshop cs3 and cs4 on Vista) and I get color looking more like bronze looking but when I do print, it comes out just like it should (in working mode which is Monitor RGB with Proof colors checked).
This setting is the only one I've used to make sure image/psd looks exactly like what it should when printing. I tried the default Working CMYK with and without Proof colors but it's still showing me the bronze look instead of silver. I've looked on the net and no exact easy fix for this was found. I really really appreciate any help.
Another simple question is regarding size. I'm working on a document size of 17.5 x 8.7 inches and the actual Banners will be printed at size 175 x 87 inches (5 banners each at 35inch wide but combined into a big one). So essentially, I'm working at 10% the size of what the final print will be and my file size is 760mgs. You can only imagine how big the file would be if I work on the actual size.
I am desperate and cannot think what else to try? I used Lr 3.6 to create custom (4 identical) photos to print on Kodak 210x297 mm (A4) glossy paper, using an HP 309a Photo-smart Premium inkjet printer. The size on the computer screen looks correct, in that the 4 pictures take up the whole A4 sheet. However, when I print, only one quarter of the photo paper is used, -ie., the 4 prints are all in one corner, and each print is like a tiny thumbnail. I have tried to vary the way I set this up by using different templates but nothing I do works at all, and I'm just wasting more and more paper.
I'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
I have two layers. One is set to red color, the other to blue color (using ctb). I have both layers defaulted to 1 mm line weight thickness. Blue is continuous and Red is dashed.
When printing the blue layer prints at the correct weight of 1mm, while the dashed red layer prints at a much smaller thickness. All line properties are set to default or bylayer (this is not being caused by the lines having individual special properties).
When printing from PS CC using the print dialogue box I am getting a severe red shift in the final print. When I print the same image from PS CS5 or CS6 I get a color-correct print.
I am running a MacPro with OS 10.7.5, and printing to a Canon iPF8300 with its latest firmware and print driver. I am using the proper ICC profile for the paper. In the print dialogue box, I select "Photoshop Manages Colors".
A couple things I noticed: In the "Print Settings" where I dial in the printer setup, the settings for "Color" are both turned off (Colorsync & Vendor).In the printer driver settings (still within "Print Settings") the "Color" tab is grayed out, but when I click the "Settings" for that sub-panel, Colorsync is selected.When I printed the image from the Canon PS Plug-in, the red cast was gone, but the blacks were too heavy (there is no "Black Point Compensation" check box available because the Canon plug-in uses Adobe Color Engine for that, and it's only 32-bit and won't run).
I have just bought and installed Lightroom 5 and need to set my print size to A3 and in the future even bigger. I do not have the facility at home and need to have them sized correctly for the print shop so they do not have to waste time resizing them. I am at a loss how to do this. I cant find any settings for this size print. A3 is roughly 42 x 29.7 cm.
I am working with CS6 windows. I am having a problem when I made a brush, and add additional strokes to the same line.
Here is a pic of what is happening. You can see at the beginning of the arrow, there is a blue and pink link showing around the beginning of the arrow head. I added the pink and blue lines to the same line as the brush using the appearance tab.
Now if I add a dash to the the pink and blue lines, this is what happens... There is a little pink and blue line at the very tip of the arrow head. My dash options use for both the pink and blue lines.
My question is how to I get rid of this little line? What I am trying to do is.. use the black arrowhead on line with a stoke of 1 point black, and then under that have a 3 point stroke of white. In the image what is blue would be white, and what is pink would be black, and the arrowhead is correct as it is now. I had this same setup in CS4, and did not have that little line at the beginning.
I've just recently caught up to 2.8 (From 2.4 something or other believe it or not ) and amongst a couple of things I have to say I don't like is the fact that previously when setting a path, if I wanted it to be either perfectly horizontal or vertical I could see by the steps in the path preview line whether it was or not.
With the new version, initially at least, that's no longer the case. As I tend to work with straight lines a lot of the time it's proving to be a bit of a pain. Is there any way to set the path preview line to show the steps again to indicate a straight line.
When I try to modify the custom properties for the HP t2300, Autocad C3D 2011 instantly becomes non-responsive and hangs. After a few seconds, every other open app suffers the same fate. If I have task manager open to the performance tab, I can see memory use escalating rapidly. Either I use Taskmanager to kill Acad quickly, or I end up killing the power to the computer and restarting the hard way,
the plotter is set up on the network with separate queues for Postscript and HPGL. Accessing the PC3 for the PS queues has no problem, it's only the HPGL queue that hangs me up, and only in C3D 2011 (and Civil3d as AutoCAD)
LDT and LDC Map 2009 do not have the problem,. nor does Map3d 2011, and TrueView 2013 is also fine. All of these are pointing to the same set of PC3, PMP, and CTB files.Other applications do not have any problem getting to the printer properties, just Civil3d 2011..
I have autocad 2013 student version installed on a MacBook Pro with OSX mountain lion, worked properly, but now I can not print anything in paper, pdf, or preview. I just try re-installing the software, creating new layout, select the printer from "Edit page setup" menu, without any results.
I have the 2013 civil 3D version. I am doing a site plan for school, and would like to print it out so that everything shows up clearly.
I would like to print it on a 24x36 sheet, so I have set up my page to that size. When I maximize my viewport to the page borders so that the viewport is at its largest and scale the viewport so that the entire site plan fits in the viewport, everything shows up so small in the print preview screen. The annotations show up as black bars and I can only read them if I zoom in. I have limited access to printing so I want to make sure I get it right! Will I be able to read the annotations and hatching once it has printed? Even though I can't read them in the print preview or layout without zooming in?
I am using annotation scaling, so maybe my text height is wrong? Maybe I need a larger sheet than 24x36? My viewport and annotation scales are set to 1"=20' and box drawn around my site would be about 100' x 300'.
I'm using autocad map 2000. In model view I have inserted a map as an external reference. Then I have created a plot in paper view. Here the xref background is still visible. However, when i choose plot-->full preview I can't see the xref, only the other lines I've created. I'm using a HP designJet 500 in ISO A1 and have the following plot option selected:plot lineweights, plot with plot styles, plot paperspace last.
If we're in a drawing and pick the AutoCAD application button > Drawing Utilities > Drawing Properties we can, and do, use this to enter custom propterties. Is there any way to print out a report of a drawing's custom properties? Ideally, i would like to be able to select multiple drawings and print a report of each drawing's properties.
