In Model Space my dot linetype looks fine. Once going to layout/paper the dots only appear on the vertices of my polylines. I'm in civil 3d 2010. ltgen enabled, tried psltscale at both 1 and 0. why it wont place dots evenly along the polyline like every other linetype?
View 3 RepliesI NEED TO CREATE A ROW OF 3X5 PHOTOS SPACED EVENLY ON ROLL PAPER (FINISHED PRODUCT COULD BE AS LARGE AS 13in.X44in.)
View 3 Replies View RelatedSometimes, i work with the Warp Mesh, and i need to make something with a smooth curve. I often end up with several lines following the curvy line i want but i would need to have them perfectly equidistant from one another. Is there a way to select s certain number of nodes and have them evenly space while the first and the last one stay as anchors?
View 2 Replies View RelatedI am close to getting my general legal the way i want. The only thing i hope to change now is the way the bearing is shown. it currently spits out as 89degrees 50minutes 50seconds. I simply want to add a space between the number and callout.
Example:
89 degrees 50 minutes 50 seconds.
I cant seem to find this setting.
How can I copy a linetype definition from a drawing to the linetype definition file?
View 7 Replies View RelatedI have an existing mesh based on quads.(Similar to how 'garment maker' generates a flat mesh, but wrapped around my existing mesh while keeping (close to) the same shape.
Is there a way to do that? Most remeshers will generate quads but I really need equally-spaced triangles to reform the mesh.
How to evenly space objects between 2 lines. In this instance I am trying to space recessed lights across a ceiling. If I use the divide command and snap to the node the space between the wall and the first light will be greater than the space between the first and second light.
View 4 Replies View RelatedPlace holes evenly around a hollow sphere other than the increasingly complicated way I've been trying to do it?
Gro-Ball.dwg
I need to evenly space points along a drawing of an ellipse, and I can not seem to figure out how to do this.
View 4 Replies View RelatedAny way to evenly space contours around a curve in a surface.
Many times I have a steep area in a surface that needs to be displayed using 1 foot contour intervals, and in certain areas the contours are crossing each other around curved areas, like a curve in a ditch. In the past i have had to "fudge" the surface a little to get the contours to look correct.
is there a command or even does any lisp routine to select a line and evenly divide it in to however sections you want?
View 9 Replies View RelatedI'm trying to stretch both sides of a bracket evenly from it's center point. How do I set the one (1) stretch action to stretch the two ends evenly with the parameter sets: stretch pair?
View 6 Replies View RelatedI need to create a 100 wedges 'spinning wheel' graphic (like a pie chart but does not require pie chart functionality) with each wedge of equal size and spacing but can't seem to find a process that works.
View 4 Replies View RelatedLisp routine that divided up a normal square / rectangle room and insert a block at each given point.
At present if the room was to have four lights width ways and three lights length ways we would divide the width by eight to give us 1/2 1 1 1/2 so the lights would be placed on every second point after the divde command (dividing the room by twice the amound of lights needed).
I would like to write some sort of AutoLISP program to evenly space objects across a given distance. I have attached a .pdf file showing what exactly I mean.
I would like the program to enable me to either enter or measure (via the selection of two points) the "z" distance, to enter or measure the "y" distance, and to enter the number of objects, "n". I would then like the program to evenly space "n" objects across the "z" distance.
A program like this is, I have to be honest and say, way beyond my current capabilities.
Perhaps some initial guidance to get me going?
I usually make a 6 petal flower shape by creating a petal, flipping a copy and rotating 2 copies at 60 degrees. (at left, below). But I want to make a 5 petal flower and cannot figure out how to do that. let's say I have an elongated oval and I want to rotate 4 more copies at 72 degrees. And I want it to be "mathematically perfect / evenly spaced, using the black dot as the point of rotation. how would i do that? On the right - you can see what i am aiming for, but there's no way to be perfect doing it by hand.
View 7 Replies View RelatedYou know how you can create a streight line with the line tool, well is there a way to start to bend it as you wish. For example to get a symetrical ) type curve.
View 4 Replies View Relatedusing imageready for this task and of course imageready has been integrated into Photoshop CS4.
What I want to do is evenly distribute layers around a circle, each layer must be evenly spaced.
This image is just a very quick and dirty example of what I want (aside from the fact that it isnt evenly distributed and I just painted dots around). What I want to do is evenly place these dots around the circle, each dot must be the same distance from the one beside it and across from it.
I have 5 text layers for the different sections (home, news, contact etc.) and I have them all aligned horizontally. I position the far left text layer where it needs to be, then the far right text layer where it needs to be, link all the text layers and hit 'Distribute Horizontal Centers' to have them fill out the space between evenly.
View 2 Replies View RelatedI have 4 lines of text. They are currently in 4 separate layers as they are 4 separate buttons. How do I make sure the verticle space between them is even?
View 1 Replies View RelatedIs there a method to evenly distribute objects around a circle? I understand the horizontal and vertical alignment tools, but I'm not sure how to apply them in this situation. Attached are a sample picture of what I want to accomplish and the .xar file (XDP7).
Circles01.xar
I've used the blend tool to create 10 circles going from smallest at the top > largest at the bottom. When I Align > Distribute evenly on the vertical axis - the circles aren't evenly spaced. I'm guessing ai is doing the math from the centerpoint? How can I get them distributed so that the space between each circle is the same. F- 10 px from the top of one circle to the bottom of the one above it.
View 11 Replies View RelatedHow can I space dots evenly around a circle in Illustrator?
View 7 Replies View RelatedI have an ellipse (blue shape in screen shot) 120mm tall / 135mm wide;
and then I have ELEVENT tabs (magenta in screen shot) that will be attached to this; these tabs need to step and repeat evenly around the ellipse.
how I could achieve this effect?
I need distributing horizontal strips of images into a 720x480 canvas. The images vary in heights and constant in width= 720 pixels. For example, i get a set of 17 horizontal strips. 10 strips with height of 8 pixels each, and 7 strips with height of 13 pixels each.
I need to figure out a math formula that will give me the spacing in between these horizontal strips that would allow me to put them evenly onto a 720x480 canvas.
they can not overlap.
I am working on a tee and trying to evenly include a graduating class of 44 students in the shape of an oval using 2 columns and 22 rows.
View 5 Replies View RelatedWhen I use "object/blend/replace spine" it will distribute the objects evenly around the circle, but with no rotation. My issue is that I have objects shaped like people and would like them evenly around the circle, but rotated correctly so that their feet are all touching the circular path and their heads are always facing out. How can I achieve this?
View 2 Replies View RelatedI am working on a personal data visualization project but currently stuck and can't go forward. As you can see below in the image, I created all my data bars and tried to distribute them on a 360 degree path myself.
But clearly, I couldnt able to create a perfect 360 path.
All of the bars are each group objects on their own. I am sure there is a way to distribute them perfectly on Illustrator but I cant find it. There is a option on Blend>Replace Spine but it is not active.
I am fairly new to Illustrator, currently working on a project involving circular return address lables. On the labels, the address text follows a circular path with bullets between the name, street, and city/state/zip. Now that I've entered all of the text onto the curved path, how do I distribute it evenly along that path? In other words, how do I ensure that the same amount of space exists at the beginning and end of my line of text? Right now, there is "leftover" space at the end of the address.
View 4 Replies View RelatedThe Translate K key is gone in gmask? How can you move one point evenly over multiple keyframes now?
Also, CFX clip not working. When I try and make a CFX clip it's just black frames.
I'm working in Adobe Illustrator CS6 and neither the Distribute Spaces Option nor Distribute Object Option are working.It doesn't seem to matter if it's a print or web document. Doing the same thing to the same document/graphics in CS5.1 works perfectly.
Copypasteing the correctly distributed objects from CS5.1 to CS6 works ok, and if i then repeat the Distribute spaces option nothing changes and it stays correctly distributed. (read: it doesn't badly distribute like before)