I have been trying to draw an arc with exact length and diamter but with no good result. arc.png You can see the image. Now, I want the diameter to be 137 mm and that was easy to draw To draw an arc is not difficult BUT I can´t seem to find how/where to input the exact length that I want. In my case I want it to be 297 mm and NOT 299.62 as shown in the picture. Also ONE extra question: Why can´t I use Properties to change the length of this arc?
How to correct length line Tangent Edges, Foreshortened (sheet metal drawing) ? I didn't find option to correct length line Foreshortened (sheet metal drawing) .
A coworker brought this to my attention and I was also immediately able to reproduce this. We use content center C channels and other common beams a lot. After inserting one into an assembly if you right click and select change size and edit the length it typically doesn't update to the correct length.
Example:
Insert a 10" Ansi MC/C channel any size
right click and select change size
add +.0625 to the existing length and hit apply
measure it at 10.06252 in
repeat change size and type in 10.0625
measure it at 10.0625
repeat change size and type in 10 + .0625
and measure at 10.06252 in
It seems to mess up more when you do math but it also screws up entering a simple number
10.000325 usually ends up as 10.000315 in for me.
Editing the part directly from it's parameter dialog doesn't yield anything like this.
I would like to draw a line that is a specific length, lets say 16, that originates from a specific x,y location say 10,23, that terminates at exactly atleast the y coordinate 38. I don't care about the x or the angle.
it's been awhile since I have been back to autocad. I draw a line an exact length then when I try to dimension it with a fraction it rounds up. I can't find the setting. It is say 5 1/2" but will dimension to 6"..
Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
With using superelevation wizard in Civil 3d 2012, changing the lane width is not affecting the resulted values of transion length and run-off length, Is that correct ? ( as civil is using standerd AASHTO tables which assume that lane width typically is 3.6m )
Also, There is only 2 tables for 2-lanes and 4-lanes roadway, Is it for total road width or for one directon only, and what about different no. of lanes ?
I am creating a block with attributes for a standard job. I have (4) total attributes in this block (for example: panel type, qty, length in imperial, length in mertic)
I would like my length in metric attribute to automatically populate based on the input from length in imperial.
I'm trying to create a swatch in Illustrator with our company's colors. I already succeedid in creating a palet with the RGB and CMYK colors, but I also want to do this with the PMS colors.However, I can't seem to find the correct color book in which to locate the correct PMS color.
I only have the number of the PMS color, I don't know which color book to choose?
With Inventor 2013 , user can view iProperties > Physical > Volume. After UPDATE is clicked, the application seems to recalucate and display mass information. How do I accomplish this task with API? I tried looping through all Occurrence objects, then access MassProperties.Volume, but the numbers do not match what I got from the Inventor application. The API seems to give me the Volume before the model construction (add parts, extrusions etc.) I need volumes after the final assembly.
I am putting together a catalog with some drawings from AC 2010. I am drawing in model space and printing in paper space. The view port scale is 1:1. If I print directly from Autocad to the printer, everything is fine. If I first plot to PDF from Autocad and then print, the dimensions are off by about 1/8". The dimensions read correctly, but they do not measure correctly. The paper size is 8 1/2 x 11. I would like these PDF files to be accurate in case someone needs to print them.
I have tried saving to dwf and then printing and printing out of Design Review but it doesn't make any difference. My settings in Adobe are 1:1 as far as I can tell.
I have this drawing will all hatches, the red hatch in the middle is the same hatch around it, ANSI34, with scale of 120. just because the boundary is too small it show as SOLID.
we are doing a customization of part in inventor , where we have done fork plate with constraints in model and extruding it with inputs from excel sheet. the plate size is getting changed as per the input given excel sheet.
but during the 2d drawing generation, if i take bom - the length and width columns are not coming.
I was checking my prints and noticed that the mass for the assembly was not shown correctly. The mass for each component is correct, but the mass for the assembly is less than the total mass of the parts..... how can that be?
Watch this video. The mass for my assembly is reported from iProperties as 10 lbs, but the mass for one of the parts is 60lbs. I would expect the mass for the assembly to be at least 60 lbs, but it is not. I tried a "Rebuild All" and an "Update Mass" on my assembly, but that did not fix it (30 sec mark in the video).
This assembly is part of a much larger assembly (around 35,000 parts). There are several more assemblies doing this and I need to get the mass correct.
I have a LOD in my assembly to suppress some of the components. In the assembly, it looks like the center of gravity is correct for the LOD. Now I place this assembly in an idw with the LOD active. Now I right-click on the assembly in the idw and choose "Center of Gravity". The center of gravity shown here does not represent the center of gravity for this LOD. The CG shown represents the CG of the master LOD.
Is it possible to get the center of gravity to show on the idw that represent the CG of an LOD?
I've got a question about plotting to a measurable PDF with the correct scale.
Currently, if you plot to PDF (ARCH full bleed D 24x36 paper size) using 1:1 scale of the Layout area (including viewport, title block, etc) you get a nice PDF of the appropriate plan which would print to paper at the correct scale (1/16" = 1' 0'). If you set the plot scale to 1/16" = 1' 0' then preview/plot it then it appears completely tiny (like 2% of the page size), in the bottom left corner.
However, I want to make the PDF measurable. At the moment, if you do this using a 1:1 plot, the default numbers given by the measure tool are way out of proportion (a 29' dimension in the drawing is measured as 48,294 with no units). To get it to give accurate measurements, you have to tell Reader/Acrobat to ignore document scaling in preferences, then "Change Scale Ratio" to the appropriate scale ratio (0.625 in = 1 ft). This means you can measure to scale in Reader or Acrobat BUT these options disappear once you close Reader/Acrobat.
I've noticed this annoying trait in AutoCAD 2012 when drawing a polar array that I hadn't noticed in previous versions. I used to get stuck in a loop having to repeatedly enter the number of items in the array trying to get it to move on to the next command prompt of what angle of fill I required.
Example CMD = Enter number of items or [Angle between/expression] <4>: <Type in 20 and hit Return key> CMD = Enter number of items or [Angle between/expression] <4>: <Type in 20 and hit Return key> CMD = Enter number of items or [Angle between/expression] <4>: <Type in 20 and hit Return key> Ad infinitum...
I then discovered that this only seems to happen when the cursor is left over the centre of the array you clicked on. But if it's moved to one side the correct command prompt follows the Return key. This isn't intuitive as you have to leave go of the mouse to input the required number at the keyboard, so it tends to be wherever you just clicked, and you end up in the pointless loop.
We are doing a drawing with Arabic text and the client keeps saying that it is incorrect. We asked for his font package we installed it and it is still wrong. It seems that we just can't get the text correct what is causing this problem? And what can be done to fix?
I'm trying to convert a hand drawn paper plan of our house into Autocad so that I can tweak it. I'm not bad at drawing things in autocad, but how to set it up properly for the file to be printed out in a shop on A0 at the correct scale. Either some info on how to set it up, or a template file that is already setup would be great.
i install my AutoCAD 2012 into my new computer, but after i install it get only 30 days remaining. then i try to put the activation code to activate and it keep getting that the activation code it not correct. i try to request a new activation code but no reply.
note: before i install my autocad 2012 into new computer i uninstall it in my previous computer.
I have a drawing and when I measure the width of a window it says 30.9, when it is supposed to be 1100mm. Is it possible to change the scale so that the measurement is correct?
I'm making a tube that is connected on another tube. I did this by skeleton modeling, for my tube extrusion i used Extrude To surface.
Is there any way to get the length of that extrude?
I know its possible to get the sweep length like this. Is there a way to get the extrude length as well?
'Set a reference to the active part document
Dim oDoc As PartDocument oDoc = ThisApplication.ActiveDocument Dim oDef As PartComponentDefinition oDef = oDoc.ComponentDefinition Dim opath As Path opath = oDef.Features.SweepFeatures.Item("TheSweep").Path Dim TotalLength As Double TotalLength = 0
