I have moved a mesh off to the side while I work on the 3d solid substructure the mesh covers. Now I need to move the mesh back, but it will not select the end "corner" of the mesh so I can place it back into position. This was not a problem in the past (200, but it doesn't work in our current version of AutoCad 2009. Is there a system variable or setting I need to set?
View 2 RepliesIs there any way of snapping to an intersection of a surface and a mesh or even the intersection of two surfaces?
View 3 Replies View RelatedWe recently had a draftsman that drew with snap on (he no longer works here), and now all the drawings he worked on have this setting turned on. I thought it would be as simple as opening up the drawings and either hitting F9 or clicking on the toggle to turn off snap. That doesn't seem to be the case. Snap mode seems to be tied to individual sheets, and every viewport. I have multiple sheets in a drawing and each sheet has multiple viewports. The last thing I want to do is open every drawing, click in every viewport on every sheet to turn off snap.
I have snapmode set to 0, but it will only turn it of in whatever sheet or viewport is active. I have to write a lisp routine that will go through every viewport on every sheet to set snapmode to 0?
Object Snap.jpg I want to pick the point where the circle hits the edge of the box but there seems to be no Intersection there. But they are on the same plane!
View 9 Replies View RelatedI have an assembly that has somewhere a hole with a round bar that exactly fits in this hole. But when meshing the assembly, the mesh of the hole and the mesh of the bar are different.
The result is that the different parts do only seem to touch each other at the edges of the mesh, resulting in high stresses.
See picture.
I tried to made a derived part from the assembly, but that one does not finish meshing. After 48 hours, the progress bar is still half way. While the one above did finish in about 15 minutes. What can I do to make the meshes match?
Snap commands in X6? I can not get the snap to grid to turn off. The button is off and the setting is set to off in options. Objects seem to snap all over not just to the grid. And the grid snap seems to be out of alignment-I cant seem to get objects to snap exactly to the grid.
The same files reopened in X5 are fine. This started with yesterdays install of 6.2. leaving X2 completely unusable.
I thought they were supposed to appear when the Polygon shelf is selected? I don't see them. In fact, when I select different shelves the menu items on the right half of the task bar don't change at all. Is this normal?
This is Maya 2011 on Mac OS X Lion.
I'm trying to snap one object to the other with vert snap.
It's trying to snap from the center of my object rather then the vert I am hovering over. In the Snap settings I have only "vertex" checked so it should snap to whatever vertex I hover over but no...This keeps up I'm going back to 2008 when all this worked fine.
When I drag around vector points of paths they are not constrained to the pixel grid, when the option "Snap Vector Tools and Transform to Pixel Grid" is off. This is the behavior I expect.BUT: When I drag whole paths, they snap to the pixel grid, no matter what. I even have snapping completely disabled.
This is particularly annoying when eg. creating a path for a zipper. I first make a path for the inside of the jacket or whatever, then I make one notch for the zipper and copy it over and over again for all the notches. It's very troubling when these elements snap to the pixel grid, because it's very unprecise then.
I've been drawing with Autocad for many years now, I've just upgraded to LT2012.
My problem is with the object snaps. They don't seem accurate enough. For e.g. I'll use end point to snap to a line or a corner and it will seem to work, but when I zoom in the object or the lines are not one on top of each other as they should be.
I'm doing drawings right now and the problem is just compounding as I continue. Nothing is perpendicular or parallel as they should be.
I have a pdf underlay in my dwg file and I found I can snap the object in it, end point, mid point, etc. Is this mean there are some ARX functions to retrieve the object in pdf underlay?
View 5 Replies View RelatedFrom time to time, when either moving text with a grip, or placing a dimension, or drawing a line or whatever, AutoCAD just randomly decides to snap to zero, zero. I might be miles away from zero, zero, but it still snap me there. The only way I can get around it is to turn my OSNAP off, do what I have to do and then turn it back on again. REALLY annoying. I'm using ACAD 2008, but I remember having this problem on earlier releases too.
View 3 Replies View RelatedSo you know how we have the snaps endpoint, perpendicular, midpoint etc. I want to find something like the snap "perpendicular."
Any way to start a line/pline then have it snap to another line at a 45° angle instead of perpendicular?
The only thing I could find was here
[URL]........
but I am not sure what all they are trying to do.
Is there a way to toggle snapping to a layer or xref?
When using object snap and you are drawing with a busy survey xref in the background, the mouse cursor really hunts around a lot on the contour lines and stuff instead of on what I am drawing. But, I would like to see the contour lines as I go, rather than hide the layer.
I've inherited a dozen heavily detailed drawings only they have been drawn freehand and do not conform to any snap mode or grid. Unfortunately the objects are not all out by a certain amount, so to adjust the entire drawing to conform to the nearest snap point I need to pretty much go through every single object and snap it to the nearest point, which will take weeks.
I've googled around a bit and have found a lisp that may potentially work however I'm running 2004 LT so therefore can't test this lisp until I find someone with a full version.
I'm sure I can find someone with a full copy of Autocad even if it means borrowing their computer just to re-align the objects. I've yet to test out the lisp I found [URL] .... although this lisp seems to suggest it will work with text objects, unfortunately my drawings include a range of objects including text, rectangles, plines etc.
I've taken a look at DotSoft's 'ToolPac' and will buy it if needed as it will apparently align all objects to the nearest snap, but I thought I'd check to see if there was any other easier/cheaper ways of doing it first.
Sometimes I can snap to leader lines, sometimes ACAD will not let me. Right now I can only snap to endpoints of leaders, nothing else.
Even if I type mid or int it will only snap to the endpoint.
ACAD LT14
Win7 64
AutoCAD exchange or any books that are available on the web. Everyone simply says "here, it exists" but I can't find a description of what object snap enforcement is, nor have I managed to figure it out from its behavior in AutoCAD.
View 4 Replies View RelatedI need to snap to guide lines but the only snap I can get is to the endpoint, which results in some very diagonal lines. I actually have ortho turned on because I need only 90 degree angles. Sometimes I need to move an entire line and I would like it perfectly lined up to the guideline. The line being moved is part of a polyline.
I sometimes do need to start or end at an endpoint but how do I do that then also snap to just anywhere on the guideline while maintinaing a 90 degree angle?
I need an overrule that can not snaps object in all locked layers. How to do that.
View 9 Replies View RelatedSimple problem: When I select a line, normally three grips appear; the ends and the middle. Normally, when I want to stretch (resize) a line I click one end and simply drag it to the desired location. Often it *snaps* to another nearby grip point, the middle selected grip, a line that it crosses, etc. If I zoom in I normally can put the grip any where I want to. It has worked fine up until this morning. Last night when I closed the program it worked perfectly...first thing this morning it doesn't work at all. Restarting the program and the computer had no effect.
The grip will only snap to the other origin (making it zero length) and other random points nearby. I cannot make it a random length...it must snap to those other points, and it *will not* snap to the middle point of the line, which I do all of the time.
Did I accidentally hit a CTRL+ or ALT+ key-stroke which has changed the abilities to snap?
We are not hitting F9, but the Snap Mode comes on. Not sure what is causing it. Not clicking it and not hitting F9. Is there anything else that can trigger the Snap Mode to "On"?
View 6 Replies View RelatedI have been working with ADT 2012 for a month now, and I am missing the way that my crosshairs used to snap to a grid, even if a command is NOT active. If I am zoomed in close, I used to be able to have my pickbox/crosshairs snap to the 1" grid that I have set up. However, that I only works if I have a command like "LINE". What setting do I need to change to make this work the way it has for YEARS?
View 7 Replies View RelatedI was wondering if it's possible to turn snap off on a set of layers whilst keeping it on for others?
View 2 Replies View Relatedhow to multi snap in block.dwghow to multi snap in block.
View 1 Replies View RelatedMy snap to extension feature is not working, and I'm looking to see why. In my object snap menu the extension is selected, and aside from that I'm not sure what else it could be other than bugging out.
The extention line (green dashed) will usually (but not always) show up in the vertical direction but almost never in the horizontal axis.
I used the measure command to place points along a polyline. I'd like to draw a poly from the points that were created. I can't seem to snap to those points. I don't see anywhere to get the osnaps to snap.
View 2 Replies View RelatedI've got the very basics down on autocad 2012 but was just wondering if you can use the polar command while using snap from, like for example if i want to draw a circle 180mm from another point at 45deg (@180<45)
View 6 Replies View Relatedif i'm using polyline it doesnät show any snap points?
View 9 Replies View Relatedtan.jpg
i want to snap this line to where it would be at a tangent to the arc (as right), but as you see (left) when i hover with TAN snap it picks a tangent from the pick point, not from object's orientation.
at the moment i construct a tangent by rotating a copy of my line by 90°, and snapping it to centre of the arc. then extend out past arc, where the intersection is now the point i originally wanted to pick. make sense? gotta be a better way!
I've got most of my most commonly used keyboard commands changed to simplified versions that suit me, however, I have not figured out how to change the snap commands. I still type "nea" and "per" to snap to nearest and perpendicular. How do I change these?
Also, how do you change the F keys?
Is there anyway that the whole block be invisible to snap except the pivot point of it?
View 9 Replies View Related