Most of my design work requires me to xRef an existing title block to my paperspace and vport my drawing into my titleblock in paperspace. However, when I attach my titleblock using xRef into my paperspace, the scaling went totally out. Mostly my block comes out way bigger than it is suppose to. The problem is that I have set my designs and block to function in milimeters, so basically it should scale down to the same scale right?
And also, it's quite troublesome to keep going back to my titleblock dwg to edit/save and reload it back in my design. Is there anyway to explode the xRef titleblock? Every time I tried they keep saying its an external reference. Is there any way to go around this so I can edit it without going back and forth?
I have a Mechanical drawing with numerous Xrefs. I need to make changes to the Plumbing layers which is in O-Xref layer. I have tried to bind all Xrefs but cannot bind all of them. The piping is in the O-Xref layer. I cannot explode nor can I Xref-Edit anything in this layer. This is one of a number of drawings but this is the first one that I cannot explode or edit the layer and I have never run into this problem before.
Is there a way that the file can be locked up to prevent editing?
When I import a drawing using XREF command from one file to the new file the scaling between model space becomes all messed up. making the adjustments between the two?
I'm running into a problem today setting up a drawing. The drawing has three viewports at different scales all looking at different parts of a model I have xrefed. The problem is that when I set a viewport to 1" = 50' for example, it is really being set to 1" = 50" -- off by a factor of 12. I cannot figure out where this problem stems from, but it is driving me a little crazy at the moment. I can work with it, by setting the scale with this correction factor in mind, but I would rather be able to set my viewports correctly, in case someone uses this drawing later as a go by or to do revision work.
So I am trying to make a site map for a building my buddy just bought. I found a lot map on the city's online database, cropped it to the area of his lot's block, and saved the image file. I then opened up a new autocad file and xreferenced the image. I know the front of his building on the site is 45' so I made a polyline that is the length of the facade over top of my xref image. Then I selected the image, used the scale command, selected one side of my polyline as a basepoint, used reference, entered 45' as the known length, and then selected the other end of the polyline. My image scaled but is now incredibly small. So small that the entine site isn't even 1". I keep trying but I'm doing something wrong somewhere.
It's enabled me to add an Edge Animate file to my responsive Wordpress site using the Edge Suite Plugin.
Only problem for me is that although the 3.7MB file I’ve created scales perfectly on all devices it struggles to play on smartphones. (I assume it's too big and too power hungry to play smoothly on smartphones - even since I've added a pre-loader.)
So, in an ideal world, what I need is a separate low res Edge Animate file that only plays on smartphones.
Failing that, I’d be happy with a 'Down-level Stage' image which could replace the Edge Animate animation.
For a moment I thought I’d found a solution when I came across this Adobe TV movie: [URL]
Unfortunately this clever solution only works when the new Responsive Scaling feature is NOT selected. As soon as it is selected, the animation no longer changes from one layout size to another when the browser window is reduced.
I don’t mind whether the fix is in Edge Animate, Wordpress or the Edge Suite Plugin - I just want a solution!
I know that in ACAD you can use the xref manager to see where the actual file for the xref resides on your computer/server/etc. What I'm curious about is whether or not the inverse action is possible. Can you somehow access the file (not the output sheet where it's being xref-ed) and see what other files are using it as an xref?
I've come in on a project that is nearing completion and have been assigned the task of "cleaning up the project folder." Unfortunately, there are a ton of files in the different folders that are no longer in use on the final output sheets and I need to keep the ones still in use and archive the ones that are no longer needed. What I've been doing is going through those sheets and reviewing the xref manager for each sheet to see which files are actually put onto those sheets and making a physical checklist from which to organize my findings. Once the checklist is made, I then archive all the files that are no longer being used.
Is it possible to run a lisp which can extract all the xref names, make a layer with that name and then change the xref on the layer? I have got a similar routine from earlier posts but it doesn't work if any xrefs inserted in paper space (works fine on model space). could change this routine allowing to change the layer of xref in paper space too.
(defun dxf (i a) (cdr (assoc i a))) (defun c:lxr ( ) (setq ss (ssget "x" '((0 . "INSERT"))))
I am using (trying to anyway) a :VLR-xrefSubcommandReloadItem reactor. My only question is how to get the xref/block name from the 'reactor callback data' Object ID.
I am ultimately trying to pass it to (vla-get-xrefdatabase ....), but I cannot figure out how to turn the second parameter from the reactor callback data into something I can use - for example the second parameter returned may be "65" or some other number.
when you bind an xref the link disappears from the xref manager.
is it possible to bind an xref, but preserve that link in the xref manager? i realize that will lead to two copies of the same object in the drawing (one xref, plus the new block). everyone's okay with that happening.
I recieved some CAD files from the architect and am not sure if theyre drawn in 3D or in revit. But everytime I go to explode the wall the doorways dissappear.
When defining a block it is possible to choose wether the block can be exploded or not. Is there a way of undoing this. I can edit the block in full version with refedit but in LT there is no way of editing this block. I can see advantages of this setting but I imagine someone accidentilly unpicking this box and creating unexplodable blocks without noticing.
I'm trying to explode a 3d block that I created from a manufacturer's horizontal mullion detail. Whenever I do that, it disappears. I tried setting it to layer 0, still disappears. I made sure all the layers were turned on and thawed. Whats weird is that I can explode the vertial mullion block and it doesn't disappear. I tried matching the vertical mullion properties to the horiz, still no luck.
I've been searching for a routine to explode minserts but haven't found anything yet that works. However, this one did. It's a vlx.
Just copy it to your Support folder and load it ("AP"). Type "explodem" at the command line to run it. It first asks you to select the block; it then asks you if you want to explode? [No/Yes] Enter No. Yep, enter no. (I know; I tried Yes but it wouldn't work...might be just me though cuz I'm a bit dyslexic; either that or the programmer may be?)
I'm trying to export some AutoCAD files to SketchUp as DWGs... everything comes through fine, but the text (and certain other line-types) won't transfer over. I know that with AutoCAD 2008 using Express Tools, you could do this easily by exploding the text. How can I explode text using AutoCAD 2013, so that it will export as vectors in the DWG file?
For some reason the line type scale is way out to lunch on one of the lines in a block i use, so i was wondering if you can change that LTS without exploding the block, or if i can change the LTS for the layer that specific line is on without exploding the block
I create schematics of lighting control systems for my job, the controllers on my schematic have multiple outputs which I need to modify so they're relevant to the job.
At present I have all my blocks in a tool palette and just click and drop to add them to my schematic.
How can I tailor the text of a block without exploding it? Is this even possible?
I have multiple dynamic blocks that I would like to add descriptions to. If I have a block in a tool palette, I can add a description by right clicking and selecting "Properties." But I would like to add a description that shows up in the Design Center as well.
Is there a way to do this without redefining the block? Exploding makes me lose all of my dynamic properties, and I'd hate to have to recreate them.
I'm using LT 2008, by the way, so I don't have ref edit or any of that other cool stuff.
How do I get the full Xref Path name instead of Xref.dwg? I'm scratching my head is this totally under my nose... cause I don't see where the property is stored. I'm getting EV_BDR.dwg instead of C:folderEV_BDR.dwg
Is there a way if I want my suface to be exploded for the components to be sent to different layers. For example if I make a building pad using the grading tool and create a surface for a design. I would like the minor and major contours to be on different layers. Same for my grading I would like my cut daylight boundary to go to a CG-Cut and fill daylight boundary to go to CG-Fill layers. Is there a way to do this? It would really streamline my work designing pads.
If I modify a 3D solid and it is left with two seperate pieces it is still one solid piece, even though there are two parts. My question is: What if only need one of those two sides? If I explode the object and delete the one side I cannot change the remaining object into a 3D solid. It remains as surface object.
How can make an object into a 3D solid after exploding it? I belive there is a simple command like union or some other but I can't remember.
I have to put out record drawings that contain C3D objects; Surfaces, Contour labels, Points and Point tables.
Many drawing Xrefs are nested. I tried the Civil batch converter with xref binding turned off and objects set to explode, and I get error messages, and the task is never completed. Is there a work around procedure to preserve the C3D information in each drawing? Can points be exploded and retain their apperance?
I have several featurelines that I wish to explode to be 3D Polylines (bad, I know, but it's a test for a way to get data across from our design group to our survey group).
Last week, in this drawing, I exploded a large selection of featurelines and they all became 3D polylines, preserving their elevation data. This week, I drew an additional set of featurelines in the same drawing. When I explode them once, they lose all elevation data, becoming lpolylines at z=0. Additionally, the Prospector shows me several errors: "breaklines not added to surface" or something similar. Which is an odd result for the explode command.
I have encounter some text exploding problem. As shown in attachment, I would like to know if there any possible way I can explode the text into polyline or single line and maintain it within the position and style?
I have a series of block references in a tool palette which I want to explode once inserted. Simple I think, just set the 'explode' property on the tool palette icon.
Wrong. What actually happens is that in my case where the block refernce is simply two blocks inserted on different layers, the tool palette will insert onto the layer specified, and then explode, moving each block from its original later, onto the layer the host block is inserted on.
For example:
BlockRef_A consists of two enties: BockRef_1 on Layer1Blockref_2 on Layer2
Using the tool palette to insert and explode using the 'use current' for the destination layer, I get the following:
BlockRef_1 on 0 BlockRef_2 on 0
Both the destionation layer (Layer1 Layer2) already exist in the target drawing.
It looks to me like autocad is importing the block, exploding it, moving it to the required layer.
This doesn't happen to any other entities, if there's a block that consists of a mix of parts, only the block references within it get moved to the destination layer.
ACad, MEP, 3DS Max Windows 7x64 X5482 @3.2Ghz 8Gb Ram Quadro FX1700
I have a problem in autocad7, once i explode text to make it a vector the vectors go from being curves or radius to straight lines, how to make them into curves as we have to run a cutter path the only thing is they cant be splines.
I'm trying to create blocks which will be used in multiple drawings for Gridlines and detail marks.
These blocks are basically a circle with an attribute in the centre, and once created as a block are annotive as they will be displayed in multiple viewports.
I can create the block with attribute fine using the "block" command which then allows me to make the block annotive ( The "wblock" command dose not allow this )
However when I insert the block into a drawing I need to explode the block before I can edit the attribute ( even though I explode the block it's still actually blocked )
