AutoCAD .NET :: Offset Quantity Using GetOffsetCurves To Be A Negative
Aug 9, 2011
I've modified my offset quantity using GetOffsetCurves to be a negative number so as to ensure that my offset polyline is always inside the original but it is working erratically. Sometimes it is outside with a negative number and other times inside. I was thinking of testing the resulting Plines length to ensure that it is smaller (I realise there could possibly be morew than one but this would not happen in my case.)
Does this sound overly cumbersome? Would a rollback be necessary to "undo" the polyline if it is longer and therefore outside the original?
View 7 Replies
ADVERTISEMENT
Dec 22, 2013
Is there a way to make the offset path not close the gap(red arrow)/not disappear if the two paths collide? like if the paths gets x milimeter close, then they dont offset anymore?
View 3 Replies
View Related
Jun 22, 2013
I have a path that turned out to be a litt ethicker than it needs to be.
I see that I can expand a path with Offset Path. I have read online that you can contract a path by entering a negative number, but when I try that, it ignores the minus sign and expends the path instead.
Is there some other way to contract the path?
View 5 Replies
View Related
May 9, 2012
just purchased LR4 and PSE 10. Set up LR4 to use PSE 10 as the editor. I watched a Tim Gray video demonstrating this and followed the steps. When I attempted to send photos over to PSE through LR nothing happened.
My system is OS X 10.7.3
View 4 Replies
View Related
Jun 7, 2013
I need an offset lisp routine to offset a selected line a set distance on each side of the selected line and change the layer of the offset lines to the current layer, and then keep prompting me to select the next line for offsetting until I'm finished.
View 3 Replies
View Related
May 14, 2012
I am trying to create a station-offset label style that will drop the trailing zeros in the offset section - e.g. 15' instead of 15.00', but if the offset is not at a whole number, e.g. 15.01, etc. it will display the entire offset.
I created two expressions: IF(OFFSET-TRUNC(OFFSET)=0,.1/12,.00000001/12)
and this one: IF(OFFSET-TRUNC(OFFSET)!=0,.1/12,.00000001/12)
I then created two offset components, one called truncated, and one called full, and assigned the heights to match the expressions.
I have attached the file, the style is ACHD-Sta Off-Rt [copy]
C3D 2011, Win x64
View 9 Replies
View Related
Nov 28, 2013
I need a pit configuration, and I use the offset command to offset a base polyline to first 10 m and then 3 and so on.. is there a way to do this in an automatically way, that you can choose the lenght of the offset for each "offset" (i.e. 1st 10 m, 2nd 3, 3rd 10 m, 4th 3 m, and so on. I am actually using civil 3D.
View 2 Replies
View Related
Apr 9, 2013
I am using MAYA 2012 on Windows 7. When I import audio (.WAV) it works fine, but if I offset it to a later frame the waveform moves to the right frame but when scrubbing the audio stays at 0. Making if very difficult to lip-sync. I have tried re-caching, playing the scene all the way through and all other options I have seen online.
View 1 Replies
View Related
Jun 20, 2013
I'm trying to change the value of the qty in the bom using ilogic with this expression
ThisBOM.OverrideQuantity("Model Data", "Steps", "QTY_STEPS")
but it gives me the following error
Conversion from string "QTY_STEPS" to type 'Integer' is not valid.
View 2 Replies
View Related
Nov 14, 2012
How to compile quantities for cost estimating when the data is scattered across multiple files. Aside from generating quantities for each drawing in seperate .csv files etc., is there some way to pull the data from all the drawings at once into a single summary file?
View 9 Replies
View Related
Jul 5, 2013
Our Autocad parts lists used to calculate the weight of parts times the quantities. Now we are using Inventor and I see that the weight shown on a parts list is the weight of an individual part - although the quantity could be 2 , 3 (more than one). Is there a way to have the total weight shown equal to MASS times ITEM QTY?
View 1 Replies
View Related
May 1, 2013
I want to get my roads pave quantity measured by area , and get its report by step of every 20 meters, how its possible ?
View 1 Replies
View Related
Nov 28, 2012
how to import Quantity Takeoff Criteria to another drawing??? Created it even in the Settings tab, however when I start another drawing new Quantity Takeoff Criteria is missing.
View 2 Replies
View Related
Nov 9, 2011
Is there a way to control what the Base Quantity is in Document Settings using iLogic. I want to be able to use a form to change it to a parameter I have created.
View 6 Replies
View Related
Mar 8, 2012
For a highway project rail overpass there are 30' curved retaining walls - the height changes continuously and the footing and wall thickness steps according to the CalTrans Type-1 wall stepping standard. So the subassembly is a custom object. I'd like to query the C3D community knowledge for the QTO accuracy - and find an answer to these two questions.
The retaining wall area QTO by corridor payitem code is 3,000 m2 and by volume report (sample line) is 5,500 m2; why is there a difference?The volume given by volume report (6,300 m3) is 40% more then the volume found by CalTrans and the contractor with a 2D digitizer QTO (4,000 m3) - who is correct C3D or CalTrans?
I am working on the QTO right now and I'd like to move to the schedule this week.
View 4 Replies
View Related
Nov 26, 2013
I would like to obtain, in a structured parts list, the total number of ITEM in the sub-assembly.
See the picture attached for the example.
I have found an iLogic rule to create an user ipropertie in each part, with the total nomber of this part in all the assemby (included all sub-assemblies).
I would like to know if it is possible to obtain the total of this part only in the sub-assembly. Is it possible with an iLogic rule or VBA ?
View 9 Replies
View Related
Nov 16, 2011
I am having a bit of trouble with my "Parts List". What I want to be able to do is show the top level assembly quantity in my part drawing. From our fabricators point of view it would be eisier if they could open/pick up a part drawing and see the total quantity needed to be produced before looking at any assembly drawings. So they could produce all individual parts then grab what they need to produce sub-assemblies. I would like to do the same for my subassembly "Part list" where I would show the total need to produce my final assembly.
So far I can only show my quantity as 1 in the parts list for a single part or subassembly, or use a static value and add the quantity by hand which can change through our design/re-design process, not to mention be extremely time consuming.
View 6 Replies
View Related
Nov 18, 2011
I have a piece of steel from the content centre 165mm long. The balloon (stacked format) quantity reads 165.000mm. I've had to format the parts list to get rid of the decimal places but I can't find a way of getting rid of them in the balloon. Any format setting somewhere?
View 4 Replies
View Related
Aug 8, 2012
How can I have a component from the content library have its 'BASE QUANTITY' default to 'EACH' when I bring it into my assembly? Each time I have to reset this to 'EACH' when inserted into my assembly.
This happens in either frame generator or just placing from content center.
View 3 Replies
View Related
Jan 7, 2012
I've attached a sample part & drawing of a hollow cylinder with 6 equally spaced radial holes drilled around it.
If you change the depth of the hole you will get a different quantity of holes in the drawing hole note.
I get a hole note quantity of 6 holes which is correct if I set the hole depth to 1". Change the hole depth to 2" and the hole note quantity shown changes to 5. Change the hole depth to 3" and the hole note quantity changes to 4.
I often draw bushings with radial holes like this and have to take care to not let this behavior create a wrong drawing.
View 3 Replies
View Related
Dec 6, 2013
how to drag and drop quantity takeoff criteria between civil 3d 2013 dwg files, but I can't seem to get it to work.
View 1 Replies
View Related
Nov 17, 2009
Using Inventor 11...How do I change change the balloon (item 40) to read qty of 2? There are 4 total in the assembly, but this particular balloon only shows where 2 are, and another item 40 balloon will show where the other 2 are.
View 9 Replies
View Related
Sep 16, 2013
Im trying to generate a list of parts and assemblies that has all the quantities included in it.Ive found that if i use the structured view it does not multiply the part count by the number of assemblies, so if i export the bill of materials i wont get the actual number of parts that i require.
If i use the parts only list then it wont include the sub assemblies.the job that im working on has hundreds of sub assemblies and thousands of parts so manually adding them up is not an option.Using Inventor 2014 Pro.
View 9 Replies
View Related
Feb 8, 2013
I need to change the Base Quantity of family templates in CC from GL = ... to Each. (I know there are several different qty, but I need this to Each because of ERP-system).
I use open from CC and place a tube in an iam, and changing BOM-settings to Each on that tube. Then I replace template in the family in CC editor with this file. And everything seems OK.
When I use "Place from CC" and place a tube from this family, everything is in perfect order. The ipt has Base Quantity set to Each just like I wanted.
I use Frame Generator and insert tubes from this family, then the Base Quantity "bounce" back from Each of GL = ...
I need this to work also in Frame Generator.
View 2 Replies
View Related
Apr 11, 2013
My customer is having trouble with the part list feature inside the Inventor 2D drawing.
For example, He has a car assembly file with 4 wheels and alot more subassemblies, then he creates a view representation which only visible for 1 wheel.
When he generates the part list in Inventor 2D drawing, he go to part list >filter setting and set to ‘’Assembly view representation’’ but the quantity for the part list is still showing as 4 as per attachment.
change the value manually inside the part list table?
View 5 Replies
View Related
Apr 19, 2013
We have close to 11k of CDR files that we need to convert into PDF files because a great number of these CDR files have multiple pages in them. I'd like to be able to do this as a batch process.
I've tried this product called FoxPDF CDR to PDF converter, but it doesn't work. All it does is convert it to a PDF file, but inside the file there is nothing but a very large red pixelated shape in every single PDF file it creates. I've tried it on about 20 CDR files.
[URL].......
I couldn't seem to find a macro that can batch convert CDR to PDF on [URL].....
Any great way to do this on a large number of files?
View 2 Replies
View Related
Oct 25, 2011
Is there any way out to find out ramp quantity in revit architecture?
View 2 Replies
View Related
Apr 12, 2012
How to calculate Column quantity and gross volume.
View 8 Replies
View Related
Oct 18, 2012
Just noticed that all of my folder titles are grayed and not white and the photo quantity numbers don't show.....everything is still in place, what gives? I am new to lightroom and starting to panic!
View 4 Replies
View Related
Feb 19, 2012
Is it possible, if you have a merged BOM.row to get the total quantity of each part?
inventor professional 2011 / 2012 / 2013
View 4 Replies
View Related
Oct 30, 2012
I have a simple driveway corridor along a steep hillside. For cut, I would like to have a negative slope away from the shoulder edge. I have tried numerous approaches and all 'cut' reverts to positive. I searched and found no clear answer. It's such a short driveway, I can 'fake' it in, but I would like to calculate quantities.
Using 2012 sp1, 64bit, windows 7
View 9 Replies
View Related
