AutoCAD Inventor :: 2012 SP1 Hole Note Quantity Error
Jan 7, 2012
I've attached a sample part & drawing of a hollow cylinder with 6 equally spaced radial holes drilled around it.
If you change the depth of the hole you will get a different quantity of holes in the drawing hole note.
I get a hole note quantity of 6 holes which is correct if I set the hole depth to 1". Change the hole depth to 2" and the hole note quantity shown changes to 5. Change the hole depth to 3" and the hole note quantity changes to 4.
I often draw bushings with radial holes like this and have to take care to not let this behavior create a wrong drawing.
View 3 Replies
ADVERTISEMENT
Nov 9, 2012
is it possible to create a hole note without pitch.
i use standard thread in most cases so i just want the thread to be shown in the holenote tool on drawings (like M8 not M8x1,25)
View 1 Replies
View Related
Sep 27, 2012
I create a hole feature in part and use Hole and Thread function in drawing view. All info displayed correctly, but if the model changes - note does not! the only way to get the new thread/hole designation is by using the Hole and Thread function again.
see print screen attached - I kept changing the model and using Hole and Thread tool couple of times. They all point to the same hole but look at the results..
Reboot does not work...
Autodesk Inventor 2012 Professional x64 SP2
Win 7 x64, Intel i7 930, 6GB PC-1600, Quadro FX-1800, 250 Gb 10k RMP
View 4 Replies
View Related
Jan 14, 2013
Aside from manually adding RH or LH to a hole note leader, any way of getting the HOLE Direction (left hand or right hand) into the leader note?
Windows 7 x64 -64 GB Ram, Intel Xeon E5-1620 @ 3.6 GHz
ATI FirePro V7800 2 GB, 180 GB SSD & 1 TB HDD, Inv R2013 PDS Premium SP2 Update 3 (Build 200), Vault 2013 Workgroup Update 2 (Build 17.2.9.0)
View 2 Replies
View Related
May 10, 2012
Is it possible to get a Limit/Fit tolerance included in a Hole Note call out, such as H7 etc?
Currently, when I am dimensioning Counter Bore holes, I have to use a general dimension for CBore dia incuding the Limit/Fit tolerance and manually add the hole dia (or visa versa). This means I have to manually update any changes to hole dia.
View 2 Replies
View Related
Oct 1, 2013
See attachment. I can't get the units off of inch.
View 1 Replies
View Related
Oct 24, 2013
The "tap drill" option in hole note in idw drawing is gray out. so I was playing around with it and fix the problem luckily.
I go to hole feature model and change thread class from 2B to 3B. then, the "tap drill" option is turn on in idw drawing.
is this correct way to do it? i have few drawing to fix it. is there a faster way?
inventor 2013 sp2 and window 7
Autodesk Inventor Professional 2014
Autodesk Product Design Suite Standard 2013
Microsoft Office 2007 & 2013
Windows 7 64bit
Synergis Adept 2013
Visual Studio Express 2010
View 3 Replies
View Related
Jun 6, 2012
I am using 2011 version of inventor.
In drafting while creating note of hole there is no breaking point for arrow there is only straight arrow line( pls find attached file of DIM 01). I am not getting any setting for the same.
I want notation having breaking point. ( Ref attachment Dim -2)
View 4 Replies
View Related
Nov 28, 2012
Using 2013 sp1.1...After I change the hole size in the part, the callout in my hole note does not update. (crazy, I know).
If I pull a new hole note after the change, it has the correct dimension. But, if I change the hole size again, this new hole note does not update.I put the part on a new idw and it updates correctly, so somehow the idw is hosed.
View 2 Replies
View Related
Nov 6, 2012
I've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
View 5 Replies
View Related
May 22, 2012
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
View 9 Replies
View Related
Nov 19, 2012
I have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
View 7 Replies
View Related
Nov 28, 2012
Question: Is it possible to control the Hole Dimensions called out on the Hole Chart? As in controling leading/trailing zeros for main hole dim, alt home dim and tolerances? Can you combine the Main Dim with the Alt dim in a single column, separated with parentheses? (same with tolerance?)
View 5 Replies
View Related
Oct 19, 2012
I would like to use the hole command to place a hole in a part. When I place the hole it won't allow me to use one of the origin planes to locate the hole from. Can I only locate holes off edges?
View 4 Replies
View Related
Apr 27, 2012
I have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies
View Related
Aug 28, 2013
i use hole feature names in hole table.
i assign hole names attribute to hole feature but dont get attribute hole table.
how to get hole names in hole table.
View 1 Replies
View Related
Jun 17, 2013
While creating holes in a part, a small counter shows (when you click on a point) of how many holes there are.
Programs:
Solidworks (1998-2011)
Autodesk Inventor (R8 - 2013)
Autodesk AutoCad 2D
Autodesk AutoCad 3D
Catia V5
SolidEdge
Anvil (Very old program!)
Pro/E
View 2 Replies
View Related
Jan 29, 2012
I downloaded inventor 2012 64bit onto my computer running windows vista. Before I could install it I'd that I needed the windows vista service pack 2. After downloading and installing that it also said that I need the 971138. I also downloaded and installed that. My problem is when I install inventor 2012. It comes up with the following error: Error 1308. Source file not found. C:AutodeskAutodesk_Inventor_2012_English_Win_64bitx64InventorProgram FilesAutodeskInventor 2012Bingranite60md.dll. Verify that the file exists and that you can access it. It gives me the option of either retry or cancel, therefore I cannot complete the installation.
View 1 Replies
View Related
Jan 9, 2012
Just installed 2012 Pro last week and tried to run FEA today. Everything else is running fine. Started with existing model and had this error. Went to a simple part with rectangle sketch 6x1x.125thk and still receive error. Found multiple issues with mesher errors in forum. So I removed all Autodesk products, cleaned registry, turned off antivirus and reinstalled software and SP1 and still receive error.
View 9 Replies
View Related
Oct 20, 2011
OK then update. I select never show this message agian ever (my favorite ) - but guess what a it pops back up. Nothing is wrong with the assembly
View 1 Replies
View Related
Apr 26, 2011
I get the following error when I try to launch Fusion from within Inventor (or on it's own):
The application is unavailable. There was an error while initializing the graphics subsystem. This is likely due to one or more of the following: your graphics driver is not configured for "True Color", there was a problem installing the application, the application installation was damaged, or some other problem with the graphics hardware and drivers or the configuration of the application. More detailed information may be included below.
Also, when I try to switch to Realistic Visual Style, it will not allow me to. When I go into Application Options, Hardware, and try to set it for Quality it always goes back to Compatibility.
View 8 Replies
View Related
Jan 9, 2012
Using Inventor 2012 and using ilogic rule or VB codes to auto Save Copy AS DWG?
My old code error out when debugging. The exact error is on this code line:
DWGAddIn.SaveCopyAs(oDocument, oContext, oOptions, oDataMedium)
Autodesk has agreed that this code does not work on Inventor 2012 and that the development is working on it. This code is part of the Snippets built in Inventor iLogic Rule Browser.
View 4 Replies
View Related
Jun 20, 2013
I'm trying to change the value of the qty in the bom using ilogic with this expression
ThisBOM.OverrideQuantity("Model Data", "Steps", "QTY_STEPS")
but it gives me the following error
Conversion from string "QTY_STEPS" to type 'Integer' is not valid.
View 2 Replies
View Related
Jan 16, 2012
Op System: Windows 7 Home Premium
Processor: Intel Core I7 960
Ram 12.0 GB system 64 Bit operating system.
MIcrosoft Excel info: Excel 2010 (14.0.4756.1000) MSO(14.0.5113.5000) Microsoft Office Home and Student 2010
Inventor Info: Autodesk Inventor Professional 2012 54 bit edition
Build: 160, release 2012 RTM Date 3/1/2011
When trying to link to excel file get error "Not Implemented". Have tried the registry 'fix' - does not work. Need to get these links working to drive models. This same Excel version works fine for Solidworks which inks perfectly with no issues whatsoever. Inventor has been a problem for 2011,and now 2012 - still not working.
View 2 Replies
View Related
Feb 17, 2014
I have a document for a book with 1400 superior note numbers in it. At the end of the document is a list with the 1400 connecting note texts. Unfortunately they are NOT connected! How can I connect the note-numbers with their connecting note text?
View 1 Replies
View Related
Jul 5, 2013
Our Autocad parts lists used to calculate the weight of parts times the quantities. Now we are using Inventor and I see that the weight shown on a parts list is the weight of an individual part - although the quantity could be 2 , 3 (more than one). Is there a way to have the total weight shown equal to MASS times ITEM QTY?
View 1 Replies
View Related
Nov 9, 2011
Is there a way to control what the Base Quantity is in Document Settings using iLogic. I want to be able to use a form to change it to a parameter I have created.
View 6 Replies
View Related
Nov 26, 2013
I would like to obtain, in a structured parts list, the total number of ITEM in the sub-assembly.
See the picture attached for the example.
I have found an iLogic rule to create an user ipropertie in each part, with the total nomber of this part in all the assemby (included all sub-assemblies).
I would like to know if it is possible to obtain the total of this part only in the sub-assembly. Is it possible with an iLogic rule or VBA ?
View 9 Replies
View Related
Nov 16, 2011
I am having a bit of trouble with my "Parts List". What I want to be able to do is show the top level assembly quantity in my part drawing. From our fabricators point of view it would be eisier if they could open/pick up a part drawing and see the total quantity needed to be produced before looking at any assembly drawings. So they could produce all individual parts then grab what they need to produce sub-assemblies. I would like to do the same for my subassembly "Part list" where I would show the total need to produce my final assembly.
So far I can only show my quantity as 1 in the parts list for a single part or subassembly, or use a static value and add the quantity by hand which can change through our design/re-design process, not to mention be extremely time consuming.
View 6 Replies
View Related
Nov 18, 2011
I have a piece of steel from the content centre 165mm long. The balloon (stacked format) quantity reads 165.000mm. I've had to format the parts list to get rid of the decimal places but I can't find a way of getting rid of them in the balloon. Any format setting somewhere?
View 4 Replies
View Related
Aug 8, 2012
How can I have a component from the content library have its 'BASE QUANTITY' default to 'EACH' when I bring it into my assembly? Each time I have to reset this to 'EACH' when inserted into my assembly.
This happens in either frame generator or just placing from content center.
View 3 Replies
View Related
