AutoCAD LT :: Referenced Drawings / Blocks And Printing
Mar 13, 2012
In M'Space I have created a layout (i.e. buildings) which in P'Space is my Dwg 1. I want to reference part of that layout in what is to be my Dwg 2. On Dwg 2 I want to insert a block (paths), because my dwgs are referenced when I insert that block it appears on both P'Space layouts. I've even tried inserting the block on its own layer but of course if I turn it off it turns off on both dwgs..... Is there a way I can print both the dwgs so they individually look the way I want without having to remember to select "do not print" that layer everytime I need to print Dwg 2?
View 2 Replies
ADVERTISEMENT
Mar 22, 2013
I've begun to create tool palettes to organize my blocks and often-used items. I have no trouble creating the tool palette, inserting regular blocks, export/import of the tool palette and groups, however my problem involves Dynamic Blocks and the fact that I keep each seperate dynamic block in a different file. I do this so that I can easily insert the block into a new drawing.
I'm able to drag the dwg file onto the palette (from explorer to autocad) just fine, that way the block's reference in the palette is the original file. Although when I take this method, I don't gain the lighting bolt to signify a dynamic block.
To get the lighting bolt I insert the block into an empty drawing, save it, then drag the block over to the palette. The problem with this is that the tool palette references the saved blank drawing, not the original block's file.
My endgame is to have a tool palette that contains my dynamic blocks and that will be eventually exported/imported to other computers everytime there is a major change. I also want to be able to change the original block's file and have that change be reflected in the tool palette.
View 9 Replies
View Related
Nov 10, 2012
Is it possible to contol the visibility state of an external referenced drawing? I have an architectural plan drawing that uses a titlesheet drawing as an external reference. In my civil plan i want to use a different title sheet. Instead of having a different titlesheet drawing for the civil drawing i was wondering if i could turn my titlesheet drawing into a dynamic block. In my architectural drawing i would see visibility state #1 & in my civil drawing i would see visibility state #2.
View 1 Replies
View Related
May 18, 2012
I need to insert a table in paperspace tab that will continually count up blocks within a set area of model space ( i need to have 3 counts, 1 for each floor of a house i.e one table per tab for that floors blocks). I have used BCOUNT and DATAEXTRACTION but they only count it once and if i add more of a certain block it does not update the table.
im using AutoCAD 2012
View 1 Replies
View Related
Oct 19, 2012
I am using 2D-AutoCAD, and trying to plot a drawing on a printer, the drawing is different colors and I want to print it black on white paper, I am unable to select the proper .ctb file from the Plot Style Table pulldown, it does not show up? I have plotted other drawing sets using this method but for some reason cant do it on this particular set.
View 3 Replies
View Related
Aug 1, 2012
We are having issues with gaps in our drawings when we print using Autocad LT. It has been fine for months and one day it just started printing with gaps between certain areas. However the gaps are not consistent and the gaps only happens with lines and not text or images.
View 9 Replies
View Related
Jul 7, 2012
I am doing electrical drawings with the architect giving me an exported DWG from Vectorworks. I have XREF the background drawing that when opened is about 6 blocks of the building background and 2 blocks of the electrical devices.
Here is the problem: The architect sent me an updated DWG that only has the electrical updates without any backgrounds. My thought was to purge all and then select all the items and then copy with basepoint. Then open the original architects XREF drawing. Select those two electrical block, erase them (or move them to the size a fixed distance). Then paste as block from the other file. Then move the block to the correct location, explode, done.
Big problem: I just tons of this error in the command line referencing different block group numbers being ignored:
Duplicate definition of block Group-1265-1 ignored.
Then the block that was pasted added a background that wasn't in the old drawing and many of the items in that block was either missing or still had the old symbols. Can't figure out how to update the background with confidence that it is really updated with new information and not keeping old.
If I open a new drawing and paste that block in, everything comes in perfectly
View 6 Replies
View Related
Oct 27, 2013
AutoCad Architecture 10, How can you copy blocks to different drawings?
View 2 Replies
View Related
Dec 18, 2011
I know what is block and I am aware of its importance and how it makes life much easier and pleasant in CAD wold. But I don't know for what reason, I was unable to make it a drawing habit for myself to use it as a routine. I am unfamiliar with this command and seldom use it.
View 9 Replies
View Related
Jun 26, 2013
I am a land surveyor and am looking for a routine that will look at my txt files exported from the field data collector, and upon exporting into C3D, will look at the descriptor and place an appropriate block on the node. For example, if the collector code was for an IP (iron pin), when the points are imported into the drawing, a solid round block would be placed on each node with the IP description. Same if for trees, concrete monuments, fire hydrants, etc.
View 9 Replies
View Related
Mar 22, 2012
why pasting details between drawings and blocks, the software or hardware, hangs for what seems to be an age, but is probably more like 10-15 seconds but over a day this is costly.
View 5 Replies
View Related
Apr 25, 2011
I would like to know how to go about printing scaled drawings form the Layout tab. How do I scale everything onto a say for example A3 paper in a scale of 1:100?
View 7 Replies
View Related
Feb 3, 2012
I have an electrical drawing of a system, but the drawings are all on one page, and in order to print i have to go to print and then highlight want i want to print individually, is it possible to print all in one shot . (please see the attached file)
View 9 Replies
View Related
Aug 23, 2013
I'm trying to get my HP Officejet Pro 8600 printer to print my drawing when I have set the lineweights. Apparently, it won't show the heavier lines, consequently, all of the lines are the same width.
View 7 Replies
View Related
Aug 22, 2013
I need to insert two different (separate) title blocks into my idw drawings so both show on the drawing. One is the real Title block, and one is a Revision History block. I have listed them as Title blocks under Drawing Resources, but Inventor won't allow me to insert both. Is there any way round this?
I do not want the Revision History block as a Symbol.
Inventor 2011; MS Windows 7-64; i5-2500; 8Gb; GF550Ti.
View 9 Replies
View Related
Nov 15, 2011
I have recently been forced more to use customer supplied drawings in inventor that contain attributed AutoCAD blocks, I have been looking for a way to automate filling out these and add some consistency since they sometime ask for the same thing to be updated in several places. I have been using the "dwgblk.GetPromptTextValues(sTags, sAttr)" to get the values of these attributes but I don't know how to update the value from a property back into the attribute.
I have even thought about doing this in iLogic so that it would be easy to change from customer to customer.
View 5 Replies
View Related
Aug 3, 2011
I recently started working at an Electrical Engineering firm and one of my many tasks is to sort out their AutoCad system and bring it up to date! An issue that has only recently started happening is that our blocks don't insert at the correct scale. Some of our drawings are metric and some are imperial, and currently all our blocks are in one Imperial file (reference file for our palettes). Is this our issue, my understanding is that when you create a block you should create it as a wblock and each block should have its own file.
The problem is that some of our blocks we want to come in at scale ex/ a 2'x4' light fixture, however an electrical socket or light switch symbol we want to come in at a slightly enlarged scale so that you can easily read the drawing and see where they are located.
View 7 Replies
View Related
Apr 16, 2013
We have created a complex Inventor drawing (Inventor 2013) of a very large plant item which we need to print at about 2AO to put up on a wall for training use. We want to create a high resolution PDF file of the drawing first and then print the PDF having checked the quality and resolution in Acrobat Reader.
We have tried exporting to PDF but we found that the colour shaded fills, behind the lines, are too compressed and the resolution very poor. We tried increasing the paper size but this did not work.We have tried creating a plot file by printing to file using the driver of a large roll feed plotter and then creating a PDF from the resulting file. This was a little more successful but still a long way short of the resolution or line quality we require. When you zoom in the curved lines are very jagged and the colour fill still not good.
We tried printing to a generic Postscript driver but this was even worse as we didn't have enough control over paper size or resolution.
View 5 Replies
View Related
Dec 26, 2013
I recently upgraded my computer, and use the same AutoCADLT 2012 software I used on the old system. However, now when I print drawings or make pdfs, they are in color instead of black and white. And the pdfs in color now copy in such a way that some of the layers appear faded, are very light, and are difficult to read. How do I get the prints and pdfs back to black and white, with no color?
View 2 Replies
View Related
Aug 15, 2012
I've got a drawing that is 14"x12" and have a printer that can only handle 8.5 x 11 sheets. I need to print it out full scale because I plan on using the drawing to cut something out. In school, I have seen my teacher print the drawing across multiple sheets, and then he simply tapes the sheets together. I have tried every configuration possible and have had no success.
View 1 Replies
View Related
Jan 28, 2010
I have written a program within Inventor that list all components of an assy with their properties (iproperties and properties from Producstream) and allow an export of the bill of material to Excel with our company layout.
I want to add a function to my program in order to print all drawings that belong to an assy.
I have the list of components and I want to use the new functionality of the Producstream menu that allows us to open the attached drawing.
But I don’t know which library and which property.
View 9 Replies
View Related
Apr 10, 2006
Is is possible to "que" a bunch of drawings to be plotted? I would like to be able to open a drawing and plot it, then while it's plotting, open another drawing and plot it, then another and so on and so on. However, I get an error message stating that another plot is in process and only one plot or publish process can be active at one time. Thus, I'm forced to wait for the last one to complete before sending the next one to the plotter.
View 4 Replies
View Related
Apr 2, 2012
how to select Monochrome so I get my drawings printing in black in only? I can't seem to be able to select this function?
View 9 Replies
View Related
Dec 4, 2013
I was wondering if it is possible to make adjustments to tittle blocks across multiple drawings.
Such as changing a Rev A to a Rev B
I have to update about a hundred drawings and was wondering if there is some sort of Macro that I can use to do this without manually going into each one.
View 9 Replies
View Related
Jun 2, 2013
I am fairly new to AutoCAD. I have a AutoCAD drawing file containing 8 drawings on it. What I would like to do is to print each drawing to a single PDF pages.
View 1 Replies
View Related
Aug 13, 2013
Is there a way to increase the access time so printing is faster?
I have AutoCAD 2013 and access drawings over VPN (6 meg pipe).
Both opening the drawings and especially printing them take a very long time.
It takes about 8 seconds to open drawings, due to all the modules loading on the bottom-left of AutoCAD. Printing takes even longer than opening the drawings.
Is there a setting I can change to speed-up access time?
View 5 Replies
View Related
Feb 2, 2012
Basically we have a number of different procedures that need to be written in each drawing. Each drawing uses one of 5 or so procedures. Usually we type it out every time which is a pain or copy paste. We also tried making word documents and inserting them that way but it got a little buggy. Is there any way to have 5 or so pre made text blocks to pick which to insert onto different types of drawings but that can be global used across a few systems?
We have a small group of workers all on the vault server. Basically I just want to be able to have a finished drawing. Click something that will open a list of my pre made text blocks, and insert one into the drawing that I can scale etc. We use Inventor 2011.
View 1 Replies
View Related
May 11, 2013
What I'm interested in is finding a method of connecting several properties from several Autocad drawings to a single table. I would create several custom properties in each drawing and use some of them to fill the boxes in the drawing itself (already implemented) and some of them to fill the table which could later be printed or used in some other manner (maybe even combined with an ERP software interface). Some of the properties would be used both in the drawing and in the table. What I would really like to achieve is to be able to change the property values in the drawings by changing the values in the table and vice versa.
I know how to do it for one of the drawings but I don't know if it's possible to connect several? It doesn't have to be custom properties, it can also be a table in each of the drawing if it's easier to connect with a central table that way. I suppose the best way to gather all the drawings in one place would be to use Sheet Set Manager. A bit of a problem with the sheet set manager is that we have 5 layers set up for each of the drawings and I would like to import only one of them into the sheet set. The thing is picking them by hand would take time and that's the thing I wanted to avoid in the first place. Is there maybe an option to use only import the last active layer into the sheet set?
View 1 Replies
View Related
Oct 8, 2013
I have 200+ page drawings and need to open each dwg to erase same block and text strings. Any way to batch erase same blocks and strings in multi-pages?
View 7 Replies
View Related
May 13, 2012
The 2D drawings I am working with were exported from 3D REVIT files to 2D AutoCAD files. There are several XREFed drawings that are both mechanical and architectural from the original REVIT files that for whatever reason, the block's line weights came over with line weights of 70 in those blocks.
When I plot, the objects are a blur with the line weight so high. I tried using the command "setbylayer" but that didn't work since nested blocks still had lineweights of 70. Is there a VBA or LISP routine to run through all the blocks (including nested) that can change the line weights to a given number?
View 3 Replies
View Related
Sep 13, 2011
I am having some trouble adjusting the dimension scale to match blocks and objects in my drawings.
View 1 Replies
View Related
