I am using Win 7-32 bit version, with 4GB RAM, Auto CAD 2010.When I try to switch from " Model " to " Layout" , the command line shows" Regenerating", several times.
Sometimes AutoCad will ends in " No response" and be forced off.Additionally, when I put 5-6 drawings in one file and edit it, my Auto CAD appears to be stupid, the cross can not catch the objective point, then no response, then forced off.
My work station was recently upgraded to Windows 7, 64 bit, it now frequently crashes Acad, usually when I am saving on exiting a drawing. Bellow is one of many error messages:-
Problem signature:
Problem Event Name: APPCRASH
Application Name: acad.exe
Application Version: 24.0.309.0
Application Timestamp: 4bcbe2a9
Fault Module Name: StackHash_9a0b
Fault Module Version: 6.1.7601.17725
Fault Module Timestamp: 4ec4aa8e
Exception c0000374
Exception Offset: 00000000000c40f2
OS Version: 6.1.7601.2.1.0.256.48
Locale ID: 2057
Additional Information 1: 9a0b
Additional Information 2: 9a0b8e6e32f562d4274362daf3794b40
Additional Information 3: 9dd6
Additional Information 4: 9dd61a7a205b3fd0113f4fc4059f4a26
I am using corel x3 a long time but never, never had this kind of problem. When i work in corel enviorenment after i have finished my work i go to save my work. But then is the problem It Saves the file with Large Memory on it. let's say if the file normally would be 200 K, now it saves with 3 MB. And if i import some other files in my work then the saved file will be even bigger. If i Delete the files that were imported The Saved File will be Again the same SIZE ! Even if a take one part of the file, let's say if i import only one small text and put it in another file and save it like that, the saved file will be 2 MB. I had a lots of problems, i had saved files on this way with 23-24 MB and when i open them it takes like forever. When you look that file in corel it has nohing in it, absolutely nothing that should be 24 MB. But all of my important work is in that files how to make all things back to normal again,
View 9 Replies View RelatedI do have problem with my newly installed CorelDraw X5. Before X5 we used Corel 12 in our company.
I have project file (150 MB) with lots of text, bitmaps, vectors - about 100 pages. File opens but I can't save it. I always get OUT OF MEMORY error. I even tried to divide this file into 2 smaller parts but still doesn't work.
What I noticed - Corel X5 after clean start (without opened project) takes about 80MB of RAM in task manager. When I open project usage changes from 80MB to 1,2GB. While saving it takes 1,6GB of RAM and it crashes.
To compare - Corel 12 and after opening same project file Corel 12 takes much less of memory - about 770MB and it works without problem.
Where from comes this memory usage difference?
My PC:
Windows 7 - 32bit
4GB of RAM
Intel Core2Duo 2 x 3.0GHz
700GB free space on drive C:
Photoshop and Illustrator CS3 just stop working every five to ten minutes for periods of about 10 to 20 seconds. Photoshop palettes and windows all go blank if I click anywhere in the application space during these brownouts. Sometimes the entire system stops responding to the point all I can do is move the mouse around pointlessly.
After it does whatever it is doing the app suddenly snaps back to life and anything else I may have clicked in any application in the meantime instantly responds allsuddenlyatthesametime in a flurry of dialogs and actions. Often when Photoshop comes back the palettes have no titles and seem to have been corrupted and I have to restart the app.
It doesn't seem to matter what I'm doing though I'm not entirely sure about that. Seems that it happens most when I try to use the brush tool or apply changes to text, but that may just be because I use those tools more than others.
It will shutdown frequently or sometimes not at all while i'm using Lightroom 3.6. I have Windows 7, 64 bit system, 2.80 GHz, 8 GB Ram.
Lighroom Info indicates that real memory used by Lightroom is 1.7%, Virtual memory used is 116.5 MB.
Fan seems to be ok, my system does not indicate any over heating issues. I also use Photoshop and various other heavy programs with no issues or shutdowns.
I updated to LR 4.3, ACR 7.3, and CS6 11.0.3 yesterday even though I'm not on a Retina MBP.
Anyway, last night I was doing some edits. Opened LR catalog, edited a RAW in PS, saved the PSD which kicked back to LR. Did some final touch up using the Soften Skin adjustment tool and when I clicked on an area of the photo to make the brush stroke, LR would crash. It did it several times in a row and I finally got it to stop by clicking on the brush tool, clicking done, then reclicking the brush tool. I have LR automatically sending bug reports on crashes.
The camera files seem to be just fine, but my jpg files frequently get corrupt on export. They get these random horizontal lines through them, as well as big gray sections that begin part way through the file. If I re-export them, they usually come out all right. I would like to pin down the cause. I'll change the process priority from normal to realtime for now and see how it goes.
View 2 Replies View RelatedAbout every other time I open Lightroom or switch the catalog, Lightroom will hang. Usually some thumbnails from the catalog will be visible; if it was after starting Lightroom, the splashscreen remains visible.
I am using Lightroom 5.3 64bit on Windows 7. (The problem was already there with Lightroom 3.6, but not quite as frequently)
My main catalog has about 14.000 pictures, a second catalog about 10.000. The problem exists with both catalogs.
Sometimes, deleting all previews works, sometimes the catalog remains unopenable.
I have rebuild my catalog from scratch several times (losing all virtual copies and edit histories).
The least-data-loss method seems to be to rename the catalog directory, so Lightroom will create a new empty one. Then import all photos from the old renamed catalog.
What I have tried so far, to no avail:
- Upgrading from LR 3.6 to 5.3.
- New hardware (Mainboard/CPU/RAM/Power supply; CPU: AMD->Intel, Graphics: nVidia->Intel).
- Reinstalling Lightroom
- Deleting Preferences file
- Moving pictures from network drive to a local harddisk.
- Moving pictures and catalog to a different hard disk (physical, not just other partition).
- Stopping all unneeded services and processes, down to a bare minimum.
There is not a whole lot of other software running on my machine: Dropbox, iTunes background services, Spyder3 monitor calibration, MS Security Essentias, Epson Print driver Icon. No toolbars, desktop-apps or what have you.
ever since upgrading Gimp to 2.8.10 70% of all things I perform in Gimp results in an "The Application Has Requested The Runtime To Terminate It In An Unusual Way" crash!!! everything from using Gmic to just selecting a tool has resulted in this crash!!! text bug is gone but run time crash now new has entered Gimp!!! well back to 2.8.4!!!
View 2 Replies View RelatedI need to resize and crop an image to a certain size frequently. I took a look at pyrochild's ScriptLab, but it doesn't seem to support these features. Is there any way I can automate this in Paint.net? I know I could use other programs like IrfanView, but I really like Paint.Net and would like to use it for everything.
View 2 Replies View RelatedI'm following a Scrapbook course. When I'm attempting to assemble a page, I am frequently getting 'not responding' in the top left, and the programme freezes.
View 1 Replies View RelatedUsing Elements 8. The cursor for Clone Stamp freaquently appears as a cross with a dot in the centre rather that the circle. what is (am I doing) wrong?
View 1 Replies View Relatedwhen I try to open an existing file or create a new one -- the application will shut down unexpectedly and without warning.But I also experience application errors: 'Instruction at "0x1a3c4b6b" referenced at memory "0x00000028" Memory could not be read.
View 9 Replies View RelatedWhen I use the Adjustment Brush in Camera Raw it frequently just gives me a pin instead of a brush. How can I fix this? I'm on a Mac in Snow Leopard.
View 4 Replies View RelatedI keep getting this message come up
"AutoCAD LT is running out of system memory. Continuing the current operation may result in program failure or loss of data. Do you want to cancel the current operation."
inventor shows that I have only 1,5GB memory but i have more how to increase it?
View 7 Replies View RelatedWhile working on assembly detail drawings my system pops up a message that " Running low on memory ".
View 3 Replies View RelatedC3D 2013 crashed on me earlier today with the above error. I've submitted several Reports after the crashes. I've tried rebooting, repairing, re-installing, uninstalling and reinstalling with reboots in between. I have a presentation tomorrow and I need to fix my C3D drawings. When trying to start C3D, as soon as the splash screen is gone, I get the "FATAL ERROR: Out of memory - shutting down" AutoCAD Error Aborting error.
C3D 2012 still works and AutoCAD 2013 works, but of course I can't edit my C3D objects.
When you plot to pdf in Civil 3D, my problem is that I need to go through all the different folders to the folder that I wish the PDF to be saved, and when I PDF the next drawing, I need to go through all the folders again to find the same location folder in which to save the PDF.
There is surely a memory path that saves to last saved location, rather than having to go through the different folders and sub-folders each and every time.
Before my upgrade to 2013 from 2012, it would save in the last saved location, now it defaults back 'my documents' on my C' drive.
We have not upgraded our computers in 5 years. We did upgrade the OS to Windows 7, 64 Bit and are running C3D 2012. We are currently using Core 2 Duo E8400 3.00 GHz with 4 GB ram. I am recommending upgrading the ram to 8GB.
We have a test computer with 8 GB of ram that I ran some timed tests to determine how much of a performance increase we will get. I timed opening C3D, opening drawings, rebuilding surfaces, rebuilding corridors, editing corridors with grips and switching layouts. Based on those tests I have seen almost no improvement that I can show with timed tests.
Memory usage was 70%-75% while running the tests when with 4 GB of ram and 45%-50% with 8 GB ram. The drawings I opened were from one of our largest project. The surface drawing is 50 MB with about 15 MB of xrefs.
Am I testing the wrong functions? Are our projects too small to take advantage of the additional ram? Why are most system recommendations I see in the DGs for 12 GB of ram or more?
I am doing some 3D renderings. I created a new material and gave it an image to use. I now made a change to that material getting rid of the image file, but no matter what, this texture is stuck in AutoCAD's memory or something. Am I missing something or will I have to delete this material and start over from scratch?
View 1 Replies View RelatedI just got the attached error message when trying to exit a sketch that I was editing. Windows says I have 11Gb available so there must be a problem with Inventor. I am now stuck with no way to edit the sketch without getting this error. It's a part that was migrated from 2011 format using task scheduler. Using 2012 SP2
View 1 Replies View RelatedI'm working with point clouds. is there any physical memory limitation working with autocad. because i had 32gb ram but didn't see over 4 gb for usage by autocad. my computer's os is win7 x64.
View 3 Replies View Relatedinventor 2012
64 bit machine
12gig ram
and it says I don't have enough memory! How can this be? Its not that complicated of an assembly. I have done bigger. I excluded all the part I'm not using and they are all basic plate and tube parts. There are less than 20 parts in the assembly.
Unfortunately we had upgraded LT 2008 to LT2011. A lot of problems arose:
- LT freezes after starting wich we could only solve by upgrading .net framework to v4. Without v3.5 LT runs but
we are not able to use the ribbons, only LT classic. Is this solvable?
- When using LT, after 5 to 10min the systems runs out of memory and shuts LT down. We are under a workstation
with VIsta 64 bits with 8Gb RAM, QuadCore Intel 2,4Ghz, and 512Mb graphics.
I've recieved a drawing from a customer and i'm unable to load it. When I open it, it asks to be recovered because of a damaged file. I hit the recover button and starts to load the file but after a while comes up with an error saying "FATAL ERROR: Out of memory - shutting down." Is the file just corrupted? My memory isn't even being used. Specs are i7-2600 3.40 ghz, 16gb ram and sli nvidia 570 gtx cards.
I've also tried the recover command, but it did the same thing.
There was a second drawing they sent me too, but it comes up with a fatal error 0x0050. I've attached both drawings.
What is the reason for the error " Autocad is running out of system memory ".
when i open a drawing more than 5 mb, my autocad is getting very slow and this error is coming.
My system specifications are
intel(r) Core (TM)2Duo CPU
E7300 @ 2.66Ghz
3 Gb Ram
I could open my autocad and inventor dwg files (No I can't post them) fine w/ 2011. Now we upgraded to FDS 2013 and I keep getting this error.
Close programs to prevent information loss:
Your computer is low on memory. Save your files and close these programs:
Autodesk Inventor 2013
I have an iassembly factory that has both both iassemblies generated and checked into the vault.Both com up fine when toggling between both of them on the factory file.
My drawing BOM was looking fine until I added a couple of items to the factory assembly file (items are in all iassemblies). Now I get this "Member Count Error" showing up in certain line items.
I rebuild both iassemblies I can't get the BOM to generate properly. If I toggle to the one iassembly in the factory file the opposite one shows this error message in the BOM.
I have a issu when i use BindXRef. I have 4 XREF in my dwg. so i use à Do / While for each XREF i have found. It work fine but whrn the Xref is big File, i have the issue "Out Of memory".
So the question : How i can Force the GC to clear all memory not used. My Think is to force the GC to Clear the memory before to use BindXRef() with only one XRef before to BindXRef with another.
Here my code :
Dim LockDoc As DocumentLock = doc.LockDocument Dim MemNumBoucle As Integer = -1 Dim CollXRef As New ObjectIdCollection Do CollXRef.Clear() Dim xg As XrefGraph = db.GetHostDwgXrefGraph(True) Dim root As GraphNode = xg.RootNode Using tr As Transaction = db.TransactionManager.StartTransaction For o = 0 To root.NumOut - 1 Step 1 Dim child As [Code]......
In this example i cant BindXREf ('R+1') alone. I need to BindXRef('ARCHI') before