AutoCAD Inventor :: Studio - Unintended Zoom Out When Pressing Add Camera Action?
Mar 25, 2013
I am making an animation in Inventor Studio. I have created all my sequences for fading and constraint animations, and now I only need to move the camera around my assembly while zooming in and out with focus on the animations.
The way I have done it so far, is as following: Created a camera (Camera1).Set my view where I wanted the camera to start.Rightclick on Camera1 and set camera to view.Then go in a few seconds on my timeline, move my view to a new area and finally "Add camera action". I've done this a couple of times with success, but now I can't do it again.
As soon as I move my view to another area, and press "Add camera action", it does as intended, but now it zooms out, making the animated area small and hard to see. I want it to be zoomed in on a detailed area, but it's changing the view to the whole assembly.
View 7 Replies
ADVERTISEMENT
Oct 8, 2009
I'm using inventor 2010, In studio mode, I adjust the zoom or view that I want my camera to end with, when I click "Add camera action" bottom, that zoom change in or out,
View 1 Replies
View Related
Jun 2, 2010
For some reason when using the path option in inventor studio for camera animation the camera rolls for no reason?? I have created two helical curve sketches around my product, the outer curve is the path for the camera and the inner curve is the path for the target. Both curves are the same height and have 1 revolution. When i play the camera it works out fine untill it hits 1/4 of the way through and suddenly flips 180 degrees so now the camera is upside down, once it hits 3/4 of the way it flips back again to the correct rotation. If i dont create an inner curve for the target and place the target directly in the centre of my product with no path to follow the camera spins all over the place when it follows the curve.
View 9 Replies
View Related
Mar 25, 2011
When I Zoom in my drawing on a specific area and press F3 to come to the previous zoom level it doesn't happen. inspite of this drawing will zoom out with another sequence.
View 3 Replies
View Related
Jul 28, 2013
How to zoom in and out via the API.
I can access the camera and eye etc. but cannot find the property related to zoom. I initially thought it was to do with the position of the eye but when I use the "Zoom" by dragging the mouse button I see that the eye position doesn't change.
I would like to connect the zoom to a slide bar and zoom in and out using that.
View 1 Replies
View Related
Jul 24, 2013
how to write a code for pressing an esc button but in vba
View 2 Replies
View Related
Jul 16, 2013
I have created an "addin" to monitor the "SAVE" & "NEW" button press on Inventor.What is the possibility of AutoDesk including this feature to the next release, or better still, creating a "patch" so that inventor can be upgraded to do it automatically, without the need to write an "addin"?
For Example,
If the user presses the "SAVE" button, AutoDesk Inventor would automatically look to see if a macro called "OnSave" exists. If it does, it "runs" the macro, if it does not exist, it works exactly as Inventor does now. This also would work in a similar way when pressing the "NEW" button.
View 3 Replies
View Related
Apr 5, 2013
I am having problems with zoom, pan and rotate at high zoom level. The movements becoming jerky and delayed. But for whatever reason the problem exists in some assembly files and not in the others.
View 9 Replies
View Related
Dec 6, 2011
I am doing some detail work in a camera viewport, is there a way to zoom into the view? Not move the camera, just make an area larger so I can better animate objects.
View 5 Replies
View Related
Feb 22, 2012
Look at the vifdeo file attached. I have not problem to create one component fade out (from 100% to 0%). But how to show the another component fade in (from 0% to 100%)? Studio does not allow fade from 0% to 100%.
View 4 Replies
View Related
Jul 2, 2013
i have installed the SDK for inventor 2014, but there is no add in template for Visual studio?
can i get one from anywhere?
View 3 Replies
View Related
Jul 26, 2012
I've been working in Inventor Studio (Inventor 2011) & every time I exit & return to the assembly environment I receive an error message (refer attached). Plus if I don't move the animation timeline back to the beginning prior to exiting, my model will display in its finished position but on the timeline be at the beginning when I go back into Studio.
View 1 Replies
View Related
Jan 22, 2012
I've taken a shot of a building. I'm setting up a scene that has a realistic camera lens distance and focal length taken from measurements at the architectural location. I'm creating a mesh to go over that image and it has to line up with the photo perfectly.
There are small details on the building that I need to extrude but even in full frame view on my 30" monitor I can't get close enough. If I change to a perspective or front view to work zoomed in the mesh is off when I go back to my camera view as the perspective distortion, small as it is, is different than a front or perspective view.
Is there a away to zoom in on a section of a camera view so that I can keep working on my mesh using the camera's perspective and view distortion?
3ds Max Design (3D Studio thru Max 2014), ASUS P9X79 Motherboard,
Intel i7-3960x, Hydro H80 CPU Chiller, 32GB DDR3 Ram,
Quadro 4000 Display Adapter
View 3 Replies
View Related
Jan 14, 2014
when I save a graphic in Illustrator it sometimes creates horizontal lines over the image.
View 3 Replies
View Related
Feb 23, 2012
I collasped my animation window and I can't resize it to show my animation timeline. I can only resize the window left and right??? I have exited studio environment and re-enter and still can't resize window up and down.
Inventor 2012 Certified Professional
Software: Autodesk Inventor Professional 2012 64 Bit- Service Pack 1
Operating System:64 bit-Windows 7 Enterprise-SP1
Processor: Intel Core 2 Duo CPU P8700 @2.53GHz
RAM: 16 GB
View 2 Replies
View Related
Apr 10, 2013
I would like to animate and render a 30 second video of something similar to the attached assembly. I have been using Inventor Studio to apply animations to the components, render them as full frame AVI (800 MB files), and compress them with Sony Vegas Pro free trial (~120 MB).
The attached assembly is a simplified example and took me around three hours to model, constraints, animate, and render from scratch. Normally, the boxes are constantly starting and stopping and moving at different velocities. Defining distances and times is cumbersome especially since I need to be aware of the boxes' positions relative to each other so they do not appear to move at different speeds or overlap.
I think a solid modeling program might not be the best tool to animate loose components sitting on a conveyor belt. Inventor slows down and occasionally crashes when I get up to 40 or 50 boxes stopping and starting and moving at different velocities. I am inclined to think that 10 or 15 animated conveyor belts moving boxes with a coefficient of friction would be near impossible on my machine (modeling the belts similar to a track on a tank or a chain and sprocket, also constantly starting and stopping and moving at different velocities).
I haven't played with Showcase, 3ds Max Design, or Navisworks Simulate. Would it be worthwhile to try any of these to animate and generate videos?
View 2 Replies
View Related
Aug 3, 2010
I'm using 2011 pro. When I try to animate a positional rep in inventor studio, it complains that I don't have excel installed. (see attached image) although I do have it installed. I've put the hotfix on for excel, with no effect. I've repaired inventor and repaired excel no fix though.
View 9 Replies
View Related
Oct 21, 2012
Any way to increase DPI for image output besides rendering in Studio?
When I save as image file I get option for size, of course, but no option for DPI.
View 6 Replies
View Related
Jul 25, 2006
I have a problem with Inventor 11 Studio. The reflection on the ground made by "XZ Reflective Gp" works in a way that when rendered, it shows a partial or cut reflection of my assembly, see attached .jpg file. I have not found yet where this "reflection depth" is regulated.
View 9 Replies
View Related
Sep 20, 2011
I have two gears. In the assembly I have them setup to mesh correctly. I can drive the constraint on the pinion and the gear will follow it (some what). I wanted a better video of it, so I went into Studio. Now when I drive the constaint like before on the pinion, the gear goes crazy.
[URL]
There is a rotational translation constraint set between the pair (= to inverse of gear ratio) that works in the iam, but it is like Studion ignores it. How can I animate this to show the gear mesh?
View 1 Replies
View Related
Dec 28, 2011
I have a robot that I am animating in Dynamic Simulation. I have Imposed motion on each of the relevant joints, and can run the simulation nicely.
The problem occurs when I "Publish to Studio" I loose all functionality and the robot stays still in the Studio environment.
View 3 Replies
View Related
Nov 27, 2011
I am working on a simple animation. A camera pans and turns from isometric view to a left side view of a mechanical device, which runs all ok and at a fairly reasonable speed. Now the next thing I animated, was an angle constraint. The animation moves a lever which in turn moves some gears, and then each frame takes about half a second to elapse (an very long interval when talking about video). The strange thing is that out of Inventor studio I can supress the angle constraint and move the lever (and thus the gears too) very fluidly.
View 2 Replies
View Related
Dec 27, 2011
How to import the inventor studio animation to autodesk showcase? i have created the animation by inventor studio and i gonna record it as a movie but then i found that the movie quality is terrible and its take very very very long time to proceed if using inventor!
View 3 Replies
View Related
Jul 11, 2013
why I might be seeing this error? I get this as soon as I select the "Constant Speed" option. I haven't input any other values yet. I've already set the "constant speed" option on the animation timeline menu. I also only get this error when this sub-assembly is inserted into a higher level assembly. If I animate the same components in the sub-assembly file, it works fine. What am I missing? There are no parameters holding these components in place in this upper assembly either, that was the first thing I checked.
View 1 Replies
View Related
Sep 26, 2012
(Inv 2010 Win7 64bit 8GB RAM)
Firstly is it even worth disabling things like Studio/Frame generator/content center in the Add-in manager if I never use them? I was hoping to at least reduce initial load time for inventor.
Secondly, do i need Win7 admin permission to do it? When I uncheck 'Load on Startup' settings in the Add-In Manager they just re-check themselves.
View 7 Replies
View Related
Jan 30, 2012
Just started the rendering tutorials. Opened a iam file but could not activate the rendering icon to access inventor studio. Tried several iam drawings even created a simple one. how to get this feature to work?
View 5 Replies
View Related
Jul 30, 2013
The parts in my assembly all use the same appearance. When I come to to do a render of my model however it is rendering one of these shiny (I think thats what it called).
See attached images
Image1 shows how I want it to look (this is the opposite end of my assembly)
Image2 shows the problem
Image3 shows a different appearance give to the problem part
The problem part is derived from the other end of the assembly (the part show in image1). All the parts at this end of the assembly are created the same way. They all render fine its just this one. I have tried recreating the part but still end up with the same result.
View 5 Replies
View Related
Sep 26, 2011
I'm trying to create a scene in IV Studio using point lights. If I want to change the position of the light's target, IV won't let me.
The option is simply not available. Not in the dialog (see attached image) an not in the graphics region (clicking the glyph's).
According to the help text, it should be possible (see attached image). The problem persist in both normal lighting styles as in local lights.
View 4 Replies
View Related
Nov 8, 2013
I have an assembly inside of Inventor Studio. One of the parts inside of the assembly has a parameter that I would like to animate. When I select the "Parameters" function within the "Animate" tab on the ribbon, I get an error:
"There are no favorite parameters defined."
This worked fine when I tried the same thing with only the part inside of Inventor Studio, but not when the part is included inside of an assembly.
View 3 Replies
View Related
Jan 12, 2012
When I render a PNG image with Studio there are speckles all over it as in the attached sample.
View 3 Replies
View Related
Mar 16, 2013
I think that something is not the way it is suppose to be at my ribbon I have a Inventor Studio icon but by defaults is not active (it's grayed out) so in order to turn it on I have to go to add ins and turn Inventor Studio off and than on again and in that way I am able to activate the Inventor Studio button but after that all the buttons in the Rendering Studio tab are inactive so I cannot use them. And I cannot figure out where is the problem. Is it because I am using the student version of the software and it has some kind of limitations on the rendering engine, or it is some kind of malfunctioning of my installation. Everything else is working normally I can modell I can do a rey tracing viewport renders but I cannot run the studio environment interface.
View 5 Replies
View Related
