AutoCAD Inventor :: Positioning Of Points On Angled Plane
Oct 18, 2011
I need to accurately position a point on an angled plane, but the question is how?
I've generated the required planes, the axis to revolve the angled plane around, and of course, the angled plane itself. (See attacment)
I now need to position the point coincident to the generated axis/plane and the angled plane. I have nothing to refer to so I can't project any geometry from any face. (The vee-shaped recess is generated after the slot is extruded and its position is the resut of the breakout against the OD).
How can I do this???
View 7 Replies
ADVERTISEMENT
Oct 3, 2013
I have just started using Autocad 2010 (i know i know, its not the latest )... but anyways.
I am facing this unique problem where i have a 3d solid object in the drawing, and when the first point in a pline command falls within the boundary of the 3d solid, autocad automatically assigns some of the properties of the 3dsolid to the new polyline i draw.
so for example, in the attached file, even if i am selecting pline command and starting a command within the rectangle (start point shown as a circle), it automatically changes the z coordinates so that the resulting pline is angled to the xy plane.
I a not sure how this happens, and how I can turn it off.
View 2 Replies
View Related
Jun 20, 2007
Attached are two parts and an iFeature that I keep in the "Punch" folder and use as a punch. It is common that clearance holes need to turn into slots and vice versa. The centerpoint is the perfect locator for both. The problem is I have not found a good way to place an iFeature slot on a centerpoint as easy as I do an iPunch. This means I have to convert the part to sheet metal and then back again.
Is there an easy way to place a slot, or a similar slot like this with an iFeature? ie as easy as the Hole Feature or iPunch Feature?
The other thing I do is add an axis and plane thought the center points to aid in constraining. If I remember correctly it was not possible to include work geometry in an iFeature (at least with version 10)
View 5 Replies
View Related
Dec 17, 2012
Currently using 2012 and I had the same problem in 2010.
When I turn visibility off and on in an assembly, all previously constructed user planes, axis and points become visible.
Is there a fix available to download?
View 7 Replies
View Related
Oct 30, 2012
Watching the movie in Digital Tutors: Understanding Perspective Drawing in Illustrator - Movie 6: 7:20
In this movie, and in Adobe instructions, it says that to change a planes position onto a particluar point of an object from its default position of 0 one needs to place cursor over the point that you wish the plane to come to and hold shift down. When I do this, the plane I want to move to that point disappears. When I make it reappear, it is in its original position of 0.
how to make it move where I want it to?
View 1 Replies
View Related
Jul 13, 2013
I'm trying to create a model of arrow with which I could place in drawing in any length and orientation I want with lisp. I was imaging to place two point on this arrow and by placing the two points on my drawing, the length and orientation of the arrow would be define.
I'm trying for hours to create it and my grip for polar stretching don't stay still on my arrow (suppose to be on the peak but go far if I stretch it).
View 9 Replies
View Related
Jul 13, 2013
How to make a new work plane rotated at an angle to another plane and passing through the axis of a cylinder, or one of the main axes.On the plane commands, in V2013, i don't find an option for plane at an angle
View 1 Replies
View Related
Mar 25, 2013
I have 2 tanks, each one is an assembly in itself, and they have to be positioned on a steel skid, also an assembly and then interconnecting pipework between the two. My prioblem is that I can't seem to find a way to position the two tanks at a set distance from each other and in relation to the edges of the skid.
Because of this, my pipe router is going all over the place in trying to join up the two termination points.
View 4 Replies
View Related
Apr 11, 2006
We have written an add-in that allows you to specify position and non-uniform scaling while creating a derived part.
[URL]
Some potential uses of this add-in include:
1.. To simulate an iFeature where you add or remove material - use Sculpt to add and Split to remove material. Unlike iFeature you could edit the source and make the changes be reflected in the derived part.
2.. To simulate an iFeature that places a sketch - useful for designing frames.
3.. To design a progressive die - you might want to place, with relative displacements, multiple parts representing different stages (or configurations) of a formed sheet metal part
4.. To realign (rotate) a part - sometimes skeletally driven parts (for example, four-bar linkage members) are not aligned with their "natural" coordinate system, causing skewed drawing views
5.. To derive a part with different scaling factors in X, Y and Z directions, which is useful in mold design
6.. To integrate two skeleton systems that do not share the same coordinate system
7.. To create scaled sketches (this should become useable after R11 SP1)
View 9 Replies
View Related
Oct 23, 2013
How does one implement the use of two pivot points to control movement concurrently in the X- and Y-plane?
I 've added a Link Constraint to the salmon colored component which is linked to the red cylinder pin at far left. This pin has a Path Constraint to an Arc path which is orientated left-to-right and arching up. The pin at right has a line Path Constraint that moves down and to the right. Still image 01 shows the retracted position. Still image 02 shows the animation at 50%, the Fowler hinge follows nicely the path of the left most pin quite well. Notice no movement occurs in the down direction that would be imposed by the right pin - if it worked/was set up properly.
View 1 Replies
View Related
Mar 11, 2013
I am trying to add a button to the Quick Access Toolbar in Inventor 2013 Professional. The button shows up, but it is always at the end of the toolbar. I want it to appear befor the Open button.
Here is what I am doing:
CommandControls AssemblyQATControls = oAssemblyRibbon.QuickAccessControls;CommandControls PartQATControls = oPartRibbon.QuickAccessControls; // Add Mybutton to Quick Access Toolbars.AssemblyQATControls.AddButton(Mybutton, false, true, "Open", true);PartQATControls.AddButton(Mybutton, false, true, "Open", true);
View 1 Replies
View Related
May 29, 2012
Bolted connections between two angled surfaces?!?
Is this possible ?!! Ive been working in various CAD packages and have found this to be an issue every time. Say for instance you want to bolt through a wall onto a tapered flange, how can you select a non parallel face as the start or finish surface?
View 1 Replies
View Related
Jan 20, 2012
I am trying to make an angled tray in sheet metal by am having some trouble getting it to work out. I was unable to find an example of this type anywhere. I tried doing it as a sheet metal part first then gave up, created a standard part and shelled it. My problem is ripping the corners.
View 8 Replies
View Related
May 26, 2013
Im new in Inventor and I have a problem with creating a hole through two parts beacause they are a bit angled. Im creating the holes part by part and Im using the work point method. But unfortunately this is the result:
Im wondering if there is any other methods so I can get the holes coinciding?
View 1 Replies
View Related
Apr 8, 2013
I need to create a adaptor to go from one 96 hole array pattern to a smaller 96 hole array pattern. The pattern gets smaller in both X and Y. This would go from vertical hole to angled hole back to vertical hole. One or both of the vertical sections could be removable to allow this to be a drilled part. The center section would be a solid block.
Since each hole will be at a different angle (in two different planes) it seems like I would need to create a separate plane for each hole and extrude from that plane. In addition to being error prone, this would take a large amount of time. Is there an easier way?
It would be straightforward to create a block with points for the large 96 hole array on top and the small 96 hole array on the bottom. Is there some kind of point to point method of creating a hole at an angle? A construction line could be drawn point to point but is there a way to make a hole from that?
View 9 Replies
View Related
Nov 1, 2013
I am using Inventor 2011. I have recently just dimensioned my entire drawing using only the retrieve command, but now that the angles of my section views have changed the command is not working. In this example you can see section B will allow me to pull up dimensions (not sure why they are not aligned) but section A will not allow to me to pull anything.
View 7 Replies
View Related
Sep 17, 2003
When I pick the XZ plane to create a new sketch, then Look At it, the red origin indicator is pointing left, meaning I'm on the back side. How did I get over on the front side. Something with flip axis or something like that?
View 9 Replies
View Related
Feb 24, 2012
why can't i sketch on the ground plane? If i turn on the ground plae I assume it is a plane like any other but I can't sketch on it nor can i attach nother plane to it?
View 9 Replies
View Related
Jun 17, 2013
I have a part given to me from a customer that has ALL custom planes turned on. This file is large and has many assemblies, part, sub assy's.... too much to go thru one at a time. Can I turn all 'plane views' off at once? Why? Because I find it messy... no other reason.
View 3 Replies
View Related
Jan 1, 2012
I drew the first sketch. i want to insert an offset plane. i use the plane tool, mark 2 sketch entities and a plane is formed. i move it, but it moves only on the plane of the sketch, the dialog box for the distance doesn't appear.
View 3 Replies
View Related
Mar 30, 2012
when in assembly mode when i right click on a part workplane there is sometimes the Visibilty option and other times there is no Visibility option ?
View 3 Replies
View Related
Jun 22, 2012
All previous releases of Inventor before 2013 would display the name of the parameter that controls the offset value of a plane. While editing an offset plane you could see the name either in the title of the pop up or by holding your cursor over the parameter value. In release 2013 I have been unable to find the parameter name anywhere when editing the plane. I have a lot of equations in my models. Being able to track down bugs is difficult enough without not knowing what parameter I'm looking at.
Is there a setting I need to turn on/off to get the parameter name to display again?
View 3 Replies
View Related
Nov 12, 2013
I have a sketch on plane XY and I have another plane at an angle, which I would like to work on. How can I create a sketch on the angled plane, using the geometry from the XY sketch and which I can snap to?
View 5 Replies
View Related
Jan 23, 2013
This sheet metal part has two bends, and was created with a lofted flange feature on the XY plane:
It was then cut by two circular profiles on the XZ plane:
When the flat pattern is created, it seems to work just fine as long as the diameter of the circular cut is below a certain value. Once the diameter is increased beyond this value, the flat pattern returns a cryptic error and does not compute:
I know that the bend geometry does NOT pass through the bend axis, so I am left guessing at what the real problem is. I have attached the part. The part currently has the parameter called "Tank_ID" set to 500 in. To see the error, change the value of this parameter to 600 in. For me, the flat pattern breaks between the values of 512 and 513 in.
Why does the flat pattern work at 512, but not at 513, since there is no significant difference in geometry?
View 3 Replies
View Related
Sep 27, 2011
Possible to have more than 1 derived part in a part.
And is it possible to select on which plane and location the derived part is to be?
I have a part with a derived part but now I want to add another part to it. is this possible?
View 2 Replies
View Related
Mar 13, 2012
In the programming I found an example to place an ifeature on a face.I've modified it to place it on a face without selectset but with features. faces. item(1)
how to place it on that face with a vertex from that face or a workpoint that lies on that face.I've tried to adapt other code on this forum but can't find it.
View 1 Replies
View Related
Oct 4, 2012
I have created a part in Inventor that is not on the ground plane, is there an easy way to quickly re-position this on the ground plane ?
Cad Manager/Senior Designer
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
View 3 Replies
View Related
Jan 27, 2012
I have what I am sure is -not very complicated- part that has a goofy intersecting angle. I have created a plane for this angle to try and do the cutout but it extrudes at the 30 deg, where as I would like to extrude that 30 deg feature at 90 deg. Is this possible?
The RED text says "Currently extruding this way" (30 deg per the plane)
The BLUE text says "Want to extrude this way" (90 deg, in line with the from face basically)
Inventor 2014 PDS
View 5 Replies
View Related
May 24, 2012
I am using Inventor 2010 Professional Student. I have drawn and extruded on a plane. I need to move this plane to a new measurement (from -45 to -47). When the Edit Dimension box appears, I type the new measurement in, but the plane wont move. I have a lot of construction sitting on this plane, but it is in the wrong spot.
View 2 Replies
View Related
Apr 30, 2013
I have a one rectangular block(Control cabinet) it consists of around 100 sub rectangular blocks here problem is in my part user wants few blocks in different dimensions and different positions some time. So I created one sketch in my sketch plane then user wants more features on rectangular block then I want automatically copy and paste on same plane same sketch and same time automatically asking for dimensions(positional, length and width).
View 3 Replies
View Related
Sep 15, 2013
I need an intersection of the surface of a sphere and a plane, producing a circular line.
I do not know how to do that.
View 2 Replies
View Related
