I drew the first sketch. i want to insert an offset plane. i use the plane tool, mark 2 sketch entities and a plane is formed. i move it, but it moves only on the plane of the sketch, the dialog box for the distance doesn't appear.
View 3 RepliesAll previous releases of Inventor before 2013 would display the name of the parameter that controls the offset value of a plane. While editing an offset plane you could see the name either in the title of the pop up or by holding your cursor over the parameter value. In release 2013 I have been unable to find the parameter name anywhere when editing the plane. I have a lot of equations in my models. Being able to track down bugs is difficult enough without not knowing what parameter I'm looking at.
Is there a setting I need to turn on/off to get the parameter name to display again?
I have a vertically rectangular frame with internal frame elements at two separate levels based off offset work planes.
The lowest internal plane is offset up from the XZ plane and the highest internal plane is offset up from that lower plane. In hindsight I should have based that second plane also off of XZ, or off the height extents plane at the top of the rectangular box.
So that top third section of the box CAN be sized with a little math, but if I change the lower 2/3 of the rectangle it's going to want to follow that lowest internal plane (which I can tweak again to get what I want)...is there a way to just change the source of that higher internal planes source plane? Like switching it to XZ or the height extents?
I would like to be able to offset a 3D Sketch in a direction normal to a plane. In the attached image, I have drawn in an orange color the direction I would like the 3DSketch to offset.The white line is where the new sketch would be.
The yellow surface is the 3dsketch extend to a plane
There might be some tools in Inventor that will do what I am trying, but I have not found it yet. I have tried extend surface, but that will not take it the direction I want.
I'm new to Inventor, less than a month of experience learning by myself. I want to create an ifeature that uses sketches from 2 different planes. I found out how to place a simple ifeature but i'm having difficulty with the multiple plane references. I can select the 2 planes when inserting and tried using the "activate sketch for placement", but I can only reference the first feature, the second one isn't available at that point, therefore does not appear after completion.
View 1 Replies View RelatedI am having trouble creating an extrude-cut from an offset ellipse. It seems that when the ellipse is offset, it becomes an associative spline. I need it to remain associative with the original ellipse.
But, when I try to extrude a profile using the new spline, it won't recognize the edge.
I can't just create a new ellipse, as it's profile won't quite match the offset one. I tried tracing over the ellipse with a spline, but it then requires a vast amount of dimensions to constrain it all together.
I'm trying to extrude-cut the red outlined profile (including the elliptical part of course)..
Here is the part. I am working in Inventor 2009.
I am having a problem with some dimensions in a drawing. I have a 2D representation of my 3D model (using FLATSHOT) in my model space. I added the dimensions in a custom UCS and everything looks fine in paper space when looking at the TOP view but in model space I notice that the text is offset on the z-axis by a very large amount, like 7 meters large (I'm working in mm). How to fix the offset and get the text on the same plane as the line work?
View 6 Replies View RelatedHow to make a new work plane rotated at an angle to another plane and passing through the axis of a cylinder, or one of the main axes.On the plane commands, in V2013, i don't find an option for plane at an angle
View 1 Replies View RelatedI found much info on creating 3D objects above X Y plane (which is Z), but I haven't been able to find info on creating objects on the underside of X Y plane (sub Z).
I need to create objects above and below X Y.
I would like to create a polyline in a plane that is not WCS. I am able to do so with the 3D polyline. My problem is that 3D polyline does not allow for a Bulge in the polyline.
View 3 Replies View RelatedI am new to all these parcel/row and different way of creating a subdivision.
I need to create a right of way of 65' (35' on 1 side, 30' on the other). How can I do that? I had created my alignments not sure how to do this.
I have some cross sections showing existing and finished grade. The finished grade is a channel and floodplain with slopes to catch existing ground. I’d like to create a report of the offset and elevation at each grade break for the finished grade. Optionally, it could be offset and cut or fill at each grade break. I’ve found the tool to create annotation for the offset and elevation info, but the cross sections are too small on the drawings to accommodate all that text. Is there a way to generate a report for the section view group or even each section view that would contain that information?
View 1 Replies View RelatedI just downloaded 2013, and I am trying to learn how to use it through a book to work with my future school designs. I, of course, have little assignments to do to learn how to work the basics of this program. I am at the point where I am creating a bitmap image onto a plane. I worked it the book's way, and the selected plane did not change to the image I chose; it remained a gray color. I then looked up tutorials online and have the same results. The material editor is changing, but not in the viewport.
View 2 Replies View RelatedI need an offset lisp routine to offset a selected line a set distance on each side of the selected line and change the layer of the offset lines to the current layer, and then keep prompting me to select the next line for offsetting until I'm finished.
View 3 Replies View RelatedI am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies View RelatedI am trying to create a station-offset label style that will drop the trailing zeros in the offset section - e.g. 15' instead of 15.00', but if the offset is not at a whole number, e.g. 15.01, etc. it will display the entire offset.
I created two expressions: IF(OFFSET-TRUNC(OFFSET)=0,.1/12,.00000001/12)
and this one: IF(OFFSET-TRUNC(OFFSET)!=0,.1/12,.00000001/12)
I then created two offset components, one called truncated, and one called full, and assigned the heights to match the expressions.
I have attached the file, the style is ACHD-Sta Off-Rt [copy]
C3D 2011, Win x64
I am using AutoCAD 2013
My solid model is imported from IGES file format. I'd like to make a plane at specified location (perpendicular from the surface), and I'd like to have a cross sectional geometry cut by that plane. (attached pic.)
1. How can I make a plane following perpendicular line from the surface?
2. How can I export the cross sectional geometry?
When I pick the XZ plane to create a new sketch, then Look At it, the red origin indicator is pointing left, meaning I'm on the back side. How did I get over on the front side. Something with flip axis or something like that?
View 9 Replies View RelatedIs it possible to offset this 3D sketch1, it must still follow the curvature.
View 9 Replies View RelatedInventor 2011 will not offset polygon in sketch mode. I get "Method not supported for transient meta" error message.
View 9 Replies View Relatedwhy can't i sketch on the ground plane? If i turn on the ground plae I assume it is a plane like any other but I can't sketch on it nor can i attach nother plane to it?
View 9 Replies View RelatedI have a part given to me from a customer that has ALL custom planes turned on. This file is large and has many assemblies, part, sub assy's.... too much to go thru one at a time. Can I turn all 'plane views' off at once? Why? Because I find it messy... no other reason.
View 3 Replies View Relatedwhen in assembly mode when i right click on a part workplane there is sometimes the Visibilty option and other times there is no Visibility option ?
View 3 Replies View RelatedI have a sketch on plane XY and I have another plane at an angle, which I would like to work on. How can I create a sketch on the angled plane, using the geometry from the XY sketch and which I can snap to?
View 5 Replies View RelatedThis sheet metal part has two bends, and was created with a lofted flange feature on the XY plane:
It was then cut by two circular profiles on the XZ plane:
When the flat pattern is created, it seems to work just fine as long as the diameter of the circular cut is below a certain value. Once the diameter is increased beyond this value, the flat pattern returns a cryptic error and does not compute:
I know that the bend geometry does NOT pass through the bend axis, so I am left guessing at what the real problem is. I have attached the part. The part currently has the parameter called "Tank_ID" set to 500 in. To see the error, change the value of this parameter to 600 in. For me, the flat pattern breaks between the values of 512 and 513 in.
Why does the flat pattern work at 512, but not at 513, since there is no significant difference in geometry?
Possible to have more than 1 derived part in a part.
And is it possible to select on which plane and location the derived part is to be?
I have a part with a derived part but now I want to add another part to it. is this possible?
In Inventor 2012, if I offset a curve and then constrain the offset to the correct dimension, it always moves the original curve and the offset curve becomes the "fixed" curve. How can I change this?
View 8 Replies View RelatedWhat I have is a round part with a few features. I drew it in Inventor until I got stuck with the last feature, which happens to be a hole, on the OD of the part that is at an angle (don't care what angle so long as it doesn't intersect with the hole next to it).
I have screen shot? both the mechanical 2D version and my 'so far' Inventor version, how I can go about modeling this feature?
Btw, the hole this has to connect to is the one highlighted green in the bottom pic or the only one dimensioned in the top pic.
I have an assembly that I am trying to offset surfaces from other components to create a different part. I have this part inserted into the assembly (only planes and axis exist on this part for now).
When I try to edit it in the assembly, and select "Copy Construction" from the surfaces menu it will not select the surfaces I need. First is this the correct command? This looked like the closest to an offset surface command.
If not, what is the correct command?
I should also add that this assembly has welds in it, if that makes any difference.
I edited a sketch for an emboss to move the number over. But the resulting emboss still acts like I din not make the edit.
Inventor Suite 2013 Ultimate
Using IV 2013 and Frames.
When i get some frames and need to use the feature NOTCH, is there a way to put one offset on it ? like we can do using MITER ?
The solution we've found here is in every member that we use NOTCH, we enter in the frame part and then use the feature THICKEN/OFFSET, this wey i can get the standard offset of 3mm that we use here for welding.
Or, if there is other easy way instead of NOTCH, to make one frame get to other with offset.
The image below shows what i mean, i need to get this off set in the frames on Z AXIS.
IV 2013