AutoCAD Inventor :: Notch Or Miter A Straight Frame To Curved Frame
Dec 13, 2011There should be a way to Notch a straight frame to a curved frame! I want to laser cut the tube, so I really need to trim one tube to a curve tube.
View 8 Replies
ADVERTISEMENT
AutoCAD Inventor :: Frame - Notch With Offset
Oct 5, 2012Using IV 2013 and Frames.
When i get some frames and need to use the feature NOTCH, is there a way to put one offset on it ? like we can do using MITER ?
The solution we've found here is in every member that we use NOTCH, we enter in the frame part and then use the feature THICKEN/OFFSET, this wey i can get the standard offset of 3mm that we use here for welding.
Or, if there is other easy way instead of NOTCH, to make one frame get to other with offset.
The image below shows what i mean, i need to get this off set in the frames on Z AXIS.
IV 2013
AutoCAD Inventor :: How To Notch A Frame Against Solid Part
Oct 15, 2012I would like to know how to notch (or similar) a frame made in Frame Generator to a solid part?
I have that problem when I'll connect a truss frame to a specific part.
AutoCAD Inventor :: Custom Profile Notch In Frame Generator
Jan 6, 2014I created a custom profile, IS34, and published it successfully as a structural shape for the frame gererator. My problem is I get an error when I try to use the notch command in frame generator between two of these frame members. I have tried creating a custom notch in the profile definition, but this did not work either. I expected one profile to counter-profile the other.
IS34 Profile
IS34 Frame
Error
I am using Inventor 2013.
AutoCAD Inventor :: 2011 Frame Generator Custom Notch Profiles
May 9, 2010tried to author notch profiles in the structural members for 2011?
The what's new states:
>Publish Notch Profiles
>The Notch command is enhanced so that you can define and reuse frame cross-sections. This is particularly >useful when you need a minimal gap between two connected frames.
>You can sketch a notch profile, extrude it, convert it to an iPart, and author and publish the iPart to Content >Center. Then you can apply the notch to cut another frame during the Notch process.
AutoCAD Inventor :: How To Split Frame Member On Custom Profile Frame Generator
May 22, 2013After using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies View RelatedAutoCAD Inventor :: Frame Design - Trim To Frame Fails With Custom Profile
May 20, 2013I created an extruded aluminium profile (attached file: Item Profile 8 80x80) which I published into the Content Center. When using this profile in a frame design, and using the Trim To Frame command, the profiles are trimmed at a weird angle (attached pdf file).
View 2 Replies View RelatedAutoCAD Inventor :: How To Split Frame Member On Custom Profile Frame Generator
Apr 30, 2013After using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
AutoCAD Inventor :: When Detailing Generated Frame View Shows Elongated Frame Members
Jul 26, 2012I come across this problem from time to time and generally either just ignore it, if the detail is destined for in house manufacture, or alter it in autocad if it's destined for exterior suppliers.
Our guard frames are manufactured from extruded aluminum section (made by a company called palletti) I have when needed created a new frame generator frame member for each new x-section that we wish to use. I then draw a 2d sketch for the base frame skeleton and then a 3d sketch for all the frame work above. This I then use in an assembly to create the framework. This framework assembly then goes into a second assembly where the framework is then adorned with all the accoutrements that make up a guard frame that we can then order as an assembled frame, panels feet, hinges et al.
When placing the views for the detailing of the second assembly sometimes the view will show the wrong length for one or some of the frame members.
;note how the left and right views are different and how some of the frame members are elongated on the lh view.
I'm guessing its because of the home grown frame members but all seems to work well other wise and this only happens infrequently.
HP z210 16Gb ATI FirePro5800
Autodesk Produst design Suite 2012
AutoCAD Inventor :: Notch Of Curved Pipe
Apr 8, 2011I'm trying to notch a curved pipe with another pipe and its giving me many problems because I can't select it. What can I do to work it out?
View 9 Replies View RelatedAutoCad 3D :: How To Create Curved Window Frame
Dec 23, 2011I am having trouble trying to make a curved window frame, I can't seem to think how I can offset or make a smaller version of the outline of the frame so that it can become a 3d solid.
The picture seen below was created using the arc and polyline tool, autocad won't let me join these lines either!
Photoshop :: Reset DEFAULT Frame Rate In Frame Animation Pallet?
Nov 30, 2012I create animated gifs frequently using the Frame Animation pallet. The default frame rate starts out as 10 seconds, so I always have to change it to 4 seconds. Is there anyway to reset the default frame rate that I start out with to 4 seconds, so that I don't have to change it every time?
Preferences did not yield any promising menus
I know the standard default reset with many Adobe products is to change it without a document open, but in PS CS5.5 if you do not have a document open the frame rate option is greyed out
______________
CS5.5
MacPro Tower
Mac OS 10.8.2
CorelDRAW / DESIGNER SDK :: How To Convert Frame Into Empty Text Frame Using Macro
Dec 17, 2013how to convert a frame into an empty text frame using a macro?
View 1 Replies View RelatedPhotoshop Elements :: Apply Frame From Content Section - Frame Goes On Top Of Any Picture
Nov 25, 2012I am trying to add a frame to some pictures, but when trying to apply a frame from the content section, the frame goes on top of any picture...and not directly on to the picture.
View 2 Replies View RelatedAutoDesk Smoke :: How To Move Clip In Timeline Frame By Frame
Aug 31, 2011I'm working on a german keyboard.
Smoke 2012 SAP2 SP4
and
Smoke 2013 SP2 (Smoke Classic Keyboard Shortcuts)
Mac Pro 4,1
OS X 10.6.7
12 GB RAM
NVIDIA Quadro 4000
14 TB RAID (Areca)
Illustrator :: Scale Border Or Frame Without Scaling Frame Width?
Aug 23, 2012I'm designing some photo frames and as they come in loads of different sizes, I'd like to be able to make the frame design bigger, in illustrator, but keep the width of the actual border. i.e. at the moment it's for a 10cm x 15cm photo with a 3cm wide border going all the way round - I want to keep it 3cm for larger photos.
and here's a link to the .ai file: [URL] I have loads of other frame designs which will need similar treatment so I'm looking for a general solution rather than something that is totally specific for this design.
Premiere Pro :: How To Make Audio Play When Move Frame By Frame
Jan 5, 2014It used to be that whenever i would move the cursor in adobe premier with either the left or right arrows or by simply clicking and dragging it, it would play the audio from that frame. But it is not doing it anymore, I think i must have accidently hit a shortcut key or something to change it in settings i dont know. But it would be good if I could get the setting to change it back. I know for a fact that my laptops speakers do work, so its not that.
View 1 Replies View RelatedPhotoshop Elements :: Create A Frame Inside Frame?
Nov 15, 2013How do I creat a frame inside a frame? Elements 4.0
View 2 Replies View RelatedPhotoshop :: Saving Frame By Frame In The Timeline
Jan 27, 2013I am editing a short avi clip converted from a 1959 8mm film in the timeline. The telecine conversion results in as sharp an image as I have manged to get using PPro 5.5 unsharp mask. I tried mocha planar tracking to automatically remove a fixed spider web on the top edge of each frame in the clip.
Because the web is not distinct and the background does not progress at a steady fixed pace, the mocha procedure was not successful. Previous feedback recommended methods to mask the edge. Using various masking attempts to automate the procedure was also unsuccessful for the same reasons as mocha.
I have the time and decided to replace the spider web on each frame edge using photoshop tools e.g. clone stamp etc. - although other tools such as healing brush do not appear to work in the timeline as I expect.
My saves so far have resulted in a whole clip being saved with all following frames being modified similar to the first edited frame. Perhaps I am not using the editing procedures in photoshop from the timeline correctly.
How do I save frame by frame in the timeline?
Photoshop :: Edit Video Frame By Frame
Nov 19, 2013My band has just recorded our first music video. We are very happy with the result except that the glasses on me (the lead singer) during the close-ups look very funny, they are very skew, and the "frame" does not go behind the ear.
What I would like to do is to import the video and edit these clips frame by frame, where this is showing. There is about 15 seconds totally of me in close-up - 15 x 24= 360 images. The clips are about 1-3 seconds long. And I want to edit all of these short clips of me and then make it a full-length video again.
I made a quick edit on one of the images from the video. The shades still look a little funny but it gets better when the frame goes behind the ear. If it's possible to correct the "glass" part of the shades as well.
Photoshop :: Frame To Frame Animation
Apr 3, 2009I'd like to do some animation in photoshop, especially frame to frame animation. (such as editing images from stop motion)
But I'd like to import big quantities of images to a psd file, and which each image would automatically be imported to 1 different layer. Is it possible to do that?
The photos are fairly too high resolution to export as video (3456x 2034) so i don't want to make a video out of them and import the video sequence...
AutoCAD Inventor :: API And Insert Frame
Aug 29, 2011I am currently looking into the API for Inventor 2012 in order to try and automate a few processes that we do within our comapany.
What I am trying to do is access the functionality that the "Insert Frame" or Frame Generator function brings to Inventor by using the API. The basic functionality that I am looking for is to be able to draw a steel beam from Inventors library by using the API, similar to the way the "Insert Frame" command handles it. Is this possible? I have looked into the API documentation but cannot find anything.
AutoCAD Inventor :: Using Frame Generator
Jun 24, 2009While using the frame generator's "Trim - Extend to Face" command on short members, the wrong end of the member is being trimmed. Is there a way to choose which end to trim on short members?
View 9 Replies View RelatedAutoCAD Inventor :: How To Use Frame Generator
Oct 12, 2012How to use frame generator in assembly? I find difficult to assemble a huge assembly.
View 1 Replies View RelatedAutoCAD Inventor :: Nodes In Frame Analysis
May 3, 2013I have created a report from a frame analysis of an arrangement of I-Beam steelwork. I need to check that I have placed the nodes in the right order and this is reflected in the results of the report. I have the parent and child nodes connected at the ends of the beams as shown on the attached screen shot. I'm interested to know if the order in which I have selected the nods makes any difference to the results. There a 3 node connection points at each corner section.
View 3 Replies View RelatedAutoCAD Inventor :: DIN H-Beams In Frame Generator
Aug 13, 2013I'm running Inventor 2013 professional and I want to design a steel structure for stress analysis. But I can't find any DIN H-beams (HEB, HEA in accordance to DIN 1025) in the "insert frame member selection".
Isn't it possible to use DIN H-beams in Inventor frame generator? Can I add my own parts to the library for stress analysis?
AutoCAD Inventor :: Disappearing Frame Members?
Jan 23, 2012I'm trying to generate frame members around a combination of 2D & 3D sketches, the preview is fine however when I click apply and OK it magically vanishes
Everything is set up fine in the 'Insert Frame' dialogue box and the previews look spot on.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
AutoCAD Inventor :: Frame Generator Disappeared?
Apr 19, 2012All of a sudden I can't get up my frame generator. I click into my frame > hit "insert frame", which is normally where the dialog box comes up, but I get nothing.
Inventor Professional 2014.
Windows 7 64 bit.
AutoCAD Inventor :: Frame Generator Error
Feb 13, 2012I just recently had Inventor 2012 installed on my computer and I went to make a frame generator and an error message popped up and won't let me make the generator. I attached a .jpeg to this that shows what error keeps appearing.
View 3 Replies View RelatedAutoCAD Inventor :: Tube Frame With Connectors
Oct 10, 2013What is the best way to draw pipe frame using "KEE KLAMP" connectors?
Pipe and tube or frame generator?
AutoCAD Inventor :: End Cap Button For Frame Generator?
Aug 6, 2013Coming from a solidworks background, i frequently use weldments, or Inventor's equivalent - frame generator.
Wondering if there was a solidworks 'end cap' equivalent.
[URL] essentially a weldment driven and generated part which doesn't need much thinking about.