I am trying to add a frame to some pictures, but when trying to apply a frame from the content section, the frame goes on top of any picture...and not directly on to the picture.
View 2 Replies
I just downloaded Photoshop Elements 11. However, I've never worked with Photoshop at all. I can't figure out how to put a frame around a picture.
View 4 Replies View RelatedHow do I creat a frame inside a frame? Elements 4.0
View 2 Replies View RelatedI want to make a border/frame around a picture and add a caption. Can I do that in this program? If so, how?
View 2 Replies View RelatedOn my website, especially when pictures are side by side, I try to make all the same, i.e. square. To me it looks better. I have a picture that is rectangle and obviously cannot resize to a square - distorts the picture. I know there is a way to copy the rectangle picture into a square picture frame which allows the picture to be square while not distorting the rectangle size.
But I don't know how to do this. I have watched a video on this but still not clear how to do it.
I've got a 30 second piece of video in which a logo on a wall needs to be erased. I used the patch tool and it did a wonderful job, but only on the first frame of the clip.
View 1 Replies View RelatedI create animated gifs frequently using the Frame Animation pallet. The default frame rate starts out as 10 seconds, so I always have to change it to 4 seconds. Is there anyway to reset the default frame rate that I start out with to 4 seconds, so that I don't have to change it every time?
Preferences did not yield any promising menus
I know the standard default reset with many Adobe products is to change it without a document open, but in PS CS5.5 if you do not have a document open the frame rate option is greyed out
______________
CS5.5
MacPro Tower
Mac OS 10.8.2
I've worked out how to use the roto brush to remove a background from a subject. My question is, how do I apply these changes to all the frames?
View 8 Replies View RelatedI'm trying to use content-Aware fill to enlarge a photo into different aspect frame. The subject is in pool, surrounded by a large area of water. I've put the image in to the larger aspect ratio canvas, with a green solid background behind it, then merged those two layers together as one. I selected all the green and delted using content-aware fill. It did a pretty good job but it's also recreating some of the subject.
Is there a way that I can specify the area that it chooses from, ie the water?
i found this really beautiful image on the web and i was wondering how i can create a frame like that around my pictures, any ideas ?
View 4 Replies View RelatedI am trying to publish a profile in my library and I can not. The difference I noticed is that now I'm working on sheet metal environment and sometimes it was in part.
In the process get an error stating that there is a point in the design of extrusion ... Only if I can publish my piece is an extrusion?
Attached is the part that I can not publish
Inventor 2012
I want to find a rectangular flat section of about 250x200cm and a 150x100cm.Is that possible?
I have the content library of ANSI,JIS,GB,ISO and DIN but i can't find anything in these libraries.
After using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies View RelatedI created an extruded aluminium profile (attached file: Item Profile 8 80x80) which I published into the Content Center. When using this profile in a frame design, and using the Trim To Frame command, the profiles are trimmed at a weird angle (attached pdf file).
View 2 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
how to convert a frame into an empty text frame using a macro?
View 1 Replies View RelatedThere should be a way to Notch a straight frame to a curved frame! I want to laser cut the tube, so I really need to trim one tube to a curve tube.
View 8 Replies View RelatedI am editing a short avi clip converted from a 1959 8mm film in the timeline. The telecine conversion results in as sharp an image as I have manged to get using PPro 5.5 unsharp mask. I tried mocha planar tracking to automatically remove a fixed spider web on the top edge of each frame in the clip.
Because the web is not distinct and the background does not progress at a steady fixed pace, the mocha procedure was not successful. Previous feedback recommended methods to mask the edge. Using various masking attempts to automate the procedure was also unsuccessful for the same reasons as mocha.
I have the time and decided to replace the spider web on each frame edge using photoshop tools e.g. clone stamp etc. - although other tools such as healing brush do not appear to work in the timeline as I expect.
My saves so far have resulted in a whole clip being saved with all following frames being modified similar to the first edited frame. Perhaps I am not using the editing procedures in photoshop from the timeline correctly.
How do I save frame by frame in the timeline?
My band has just recorded our first music video. We are very happy with the result except that the glasses on me (the lead singer) during the close-ups look very funny, they are very skew, and the "frame" does not go behind the ear.
What I would like to do is to import the video and edit these clips frame by frame, where this is showing. There is about 15 seconds totally of me in close-up - 15 x 24= 360 images. The clips are about 1-3 seconds long. And I want to edit all of these short clips of me and then make it a full-length video again.
I made a quick edit on one of the images from the video. The shades still look a little funny but it gets better when the frame goes behind the ear. If it's possible to correct the "glass" part of the shades as well.
how I can get the Box, Frame or edge out of my picture? I did the inverse and feather to get a blend/shadow, but the frame is still there.
i'm having trouble fitting a particular picture into a frame. I got a picture of Floyd Mayweather Jr (BOXER), but i cant fit the whole pic into the frame because of the circular part above (see attachments below). I'm trying to make a DVD cover pic.
View 9 Replies View RelatedI come across this problem from time to time and generally either just ignore it, if the detail is destined for in house manufacture, or alter it in autocad if it's destined for exterior suppliers.
Our guard frames are manufactured from extruded aluminum section (made by a company called palletti) I have when needed created a new frame generator frame member for each new x-section that we wish to use. I then draw a 2d sketch for the base frame skeleton and then a 3d sketch for all the frame work above. This I then use in an assembly to create the framework. This framework assembly then goes into a second assembly where the framework is then adorned with all the accoutrements that make up a guard frame that we can then order as an assembled frame, panels feet, hinges et al.
When placing the views for the detailing of the second assembly sometimes the view will show the wrong length for one or some of the frame members.
;note how the left and right views are different and how some of the frame members are elongated on the lh view.
I'm guessing its because of the home grown frame members but all seems to work well other wise and this only happens infrequently.
HP z210 16Gb ATI FirePro5800
Autodesk Produst design Suite 2012
I'm working on a german keyboard.
Smoke 2012 SAP2 SP4
and
Smoke 2013 SP2 (Smoke Classic Keyboard Shortcuts)
Mac Pro 4,1
OS X 10.6.7
12 GB RAM
NVIDIA Quadro 4000
14 TB RAID (Areca)
I'm designing some photo frames and as they come in loads of different sizes, I'd like to be able to make the frame design bigger, in illustrator, but keep the width of the actual border. i.e. at the moment it's for a 10cm x 15cm photo with a 3cm wide border going all the way round - I want to keep it 3cm for larger photos.
and here's a link to the .ai file: [URL] I have loads of other frame designs which will need similar treatment so I'm looking for a general solution rather than something that is totally specific for this design.
It used to be that whenever i would move the cursor in adobe premier with either the left or right arrows or by simply clicking and dragging it, it would play the audio from that frame. But it is not doing it anymore, I think i must have accidently hit a shortcut key or something to change it in settings i dont know. But it would be good if I could get the setting to change it back. I know for a fact that my laptops speakers do work, so its not that.
View 1 Replies View RelatedI am using a student version of Inventor 2012 to design the FSAE Chassis for our University team this year. I was not able to find suitable geometry for the required tubing to make the chassis. So I found a guide on setting up a Custom Content Center and publishing parts. I have followed that. The Chassis has turned out great but now I am trying to draw it up and the BOM is not populating as desired.
A Summary:
-Custom Project file with Read / Write Library added.
-Custom tubing geometry created and published to the Library.
-Chassis constructed using standard Frame Generator techniques.
Previously I had the chassis modelled using standard Content Center parts and the BOM would populate with the individual tubes in the drawing environment. Now with the custom tubes the BOM calls up each of the individual tubing sizes, ONCE only and has large quantities. The automatic "Measure" Column is also populated with "*Varies*".
In the Frame Generator wizard each tubing size has come up as it's own "Family".I believe this is because I have published the different part sizes individually. I am guessing I should have published only the one active part but with variable geometry selectable in the "Size" drop down?
I have tried forcing the assembly into the "All Levels" view with the Bill of Materials pop-up in the Assembly environment, but even this is not populating correctly.Something else I have noticed is the individual tubes are using a different naming convention in the model tree.
We have invested much time in creating custom content center family tables based on exisiting ANSI tables, etc. so that we can suppress sizes and shapes we do not use and have the descriptions and stock numbers show up both so BOM and parts lists will roll up identical parts and as our purchasing department requires.
We have just discovered, however belatedly, that while these custom tables function just fine when placing an individual part, frame generator apparently does not see these and gets it's info from somewhere else. I have seen a similar post which references an McadForums post, but the link provided is dead.
[URL]....
How to point frame generator to customized CC familes?
I had Autodesk Inventor 2011 installed for a while, and then installed some other programs (3DS, Maya and Showcase). This caused all of my add-ins to disappear from Inventor. I managed to get them back, but now when I click the 'Insert Frame' button, I get the followin gerror: [WARNING] Problems encountered while executing frame insert command. [ERROR] Failed to read data from Content Center. [ERROR] Content Center server query failed. check your Content Center configuration to make sure all required libraries are present or check Content Center connectivity to server. I've reinstalled Inventor and reinstalled the content center libraries and the error message is still there. The content center configuration in Application Options seems fine.
View 8 Replies View RelatedQuite often I'll paint up a frame, having forgotten to switch 'current frame' to 'sequence'. Is there any way to copy and apply a current frame's paintups to the sequence after the fact?
smoke 2013 EXT1
iMac i7 3.4Ghz
NVIDIA GeForce GTX 680MX 2048 MB
32GB RAM
MAC OS X 10.8.3
Promise R6
We have customized the Content Center for Wide Flange Beams to produce BOM Descriptions that match company standards. They work beautifully until Frame Generator is used. Frame Generator just seems to do whatever it feels like doing. eg. A simple 4-sided frame made from W6X12, will produce parts with different BOM descriptions and different part numbers even though these fields are populated using expressions in Content Center. Parts of the BOM Description are formatted using the Custom Property Format in the parameters of the Family Template in Content Center. This formatting is followed at times and ignored at times.
We are using Inventor 2012 SP2, Build 219
I have been trying to add my own shapes to the Content Centre, with some success, but for being able to use them in Frame Generator. I was able to Author a new part and publish it to Structural Shapes and it works very well. However when I try to use it in Frame Generator there is an issue that I do not understand. Frame Generator recognises the family and all of the different sizes and materials, but when it come to inserting the part, i get the following message:
I am not sure what this means. The part family is in my own library in a seperate category. I don't know what/where template file needs to be and is that the same ipt file that I used to create the Content Centre part/shape? Do I need to create a new Standard rather than "attaching" it to the AS Standard?
