I want to find a rectangular flat section of about 250x200cm and a 150x100cm.Is that possible?
I have the content library of ANSI,JIS,GB,ISO and DIN but i can't find anything in these libraries.
I am using a student version of Inventor 2012 to design the FSAE Chassis for our University team this year. I was not able to find suitable geometry for the required tubing to make the chassis. So I found a guide on setting up a Custom Content Center and publishing parts. I have followed that. The Chassis has turned out great but now I am trying to draw it up and the BOM is not populating as desired.
A Summary:
-Custom Project file with Read / Write Library added.
-Custom tubing geometry created and published to the Library.
-Chassis constructed using standard Frame Generator techniques.
Previously I had the chassis modelled using standard Content Center parts and the BOM would populate with the individual tubes in the drawing environment. Now with the custom tubes the BOM calls up each of the individual tubing sizes, ONCE only and has large quantities. The automatic "Measure" Column is also populated with "*Varies*".
In the Frame Generator wizard each tubing size has come up as it's own "Family".I believe this is because I have published the different part sizes individually. I am guessing I should have published only the one active part but with variable geometry selectable in the "Size" drop down?
I have tried forcing the assembly into the "All Levels" view with the Bill of Materials pop-up in the Assembly environment, but even this is not populating correctly.Something else I have noticed is the individual tubes are using a different naming convention in the model tree.
We have invested much time in creating custom content center family tables based on exisiting ANSI tables, etc. so that we can suppress sizes and shapes we do not use and have the descriptions and stock numbers show up both so BOM and parts lists will roll up identical parts and as our purchasing department requires.
We have just discovered, however belatedly, that while these custom tables function just fine when placing an individual part, frame generator apparently does not see these and gets it's info from somewhere else. I have seen a similar post which references an McadForums post, but the link provided is dead.
[URL]....
How to point frame generator to customized CC familes?
I had Autodesk Inventor 2011 installed for a while, and then installed some other programs (3DS, Maya and Showcase). This caused all of my add-ins to disappear from Inventor. I managed to get them back, but now when I click the 'Insert Frame' button, I get the followin gerror: [WARNING] Problems encountered while executing frame insert command. [ERROR] Failed to read data from Content Center. [ERROR] Content Center server query failed. check your Content Center configuration to make sure all required libraries are present or check Content Center connectivity to server. I've reinstalled Inventor and reinstalled the content center libraries and the error message is still there. The content center configuration in Application Options seems fine.
View 8 Replies View RelatedWe have customized the Content Center for Wide Flange Beams to produce BOM Descriptions that match company standards. They work beautifully until Frame Generator is used. Frame Generator just seems to do whatever it feels like doing. eg. A simple 4-sided frame made from W6X12, will produce parts with different BOM descriptions and different part numbers even though these fields are populated using expressions in Content Center. Parts of the BOM Description are formatted using the Custom Property Format in the parameters of the Family Template in Content Center. This formatting is followed at times and ignored at times.
We are using Inventor 2012 SP2, Build 219
I have been trying to add my own shapes to the Content Centre, with some success, but for being able to use them in Frame Generator. I was able to Author a new part and publish it to Structural Shapes and it works very well. However when I try to use it in Frame Generator there is an issue that I do not understand. Frame Generator recognises the family and all of the different sizes and materials, but when it come to inserting the part, i get the following message:
I am not sure what this means. The part family is in my own library in a seperate category. I don't know what/where template file needs to be and is that the same ipt file that I used to create the Content Centre part/shape? Do I need to create a new Standard rather than "attaching" it to the AS Standard?
I am trying to create/publish custom shapes into Content Centre and for use in Frame Generator. I can create the i-Part and configure the parameters I want to enable different sizes - no problem. However when I go to "Publish Part" ()
I get the following error.......
do I need to save the ipt file in a different location? What dependencies are there? I get the same result if I follow the Inventor tutorial using the brace.ipt part....
After using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies View RelatedAfter using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
First off, we're not using Vault or ADMS as it's simply not an option at the moment. Possibly down the line - we'll just have to see, but no time in the forseable future.
I had a custom library I created on my local machine, no problems, full read/write access works fine.
Turns out there are a couple of us that need to share the library. I figured, no big deal, we'll just go out on the server and create a folder and copy them all there. I did this and configured inventor to look the server for the files. All seemed OK. It saw the files and I can insert parts into assemblies, etc. Problem is, my custom library is no longer set to Read/Write. It will only do Read Only. If I create a new library to that location, it gets created, but still only lists as Read Only.
In searching here, my guess is it has to do with permissions, but what permissions are required on the file/directory to enable Read/Write access? I already have full access to that network folder and it's contents. Does some sort of system account need added to it? Unless it's simply not possible on a network location, i'm at a loss.
I did a (I think) standard install of product suite premium 2013 a while back and am trying my first flexible hose run.
When I hit populate I get an error message saying something like "your request cannot be fulfilled because parts can"t be fetched from the content centre"
Now I see a whole lot of libraries are not available. My only other experience with this was when the mold libraries were not part of the installation and I had to do a huge download.
As far as the missing mold libraries went, I felt that was something the vendor should really have told us about. But let me not get ahead of myself this time, even though it's midnight and I can't do at least 1 run to show for tomorrow.
What is the most efficent way to share content center libraries between users? We do not use vault but do use project folders. It has been proposed to copy the CC to the server and then point the project files to that location?
Inventor 2012 Pro
Windows 7 64 bit
Core I5 2410M processor | GeForceGT 525M graphics card | 8G RAM
I installed Autodesk Inventor 2012 which I was able to download because I am a student. The version I downloaded however, did not install libraries for the Content Center. The first thing I though was that the Content Center was a feature reserved for purchased versions of the program, but when I head to the downloads section I saw a link to download Content Center Libraries.
I downloaded the ISO and ANSI libraries to try out, and placed them in the directory where Inventor is supposed to search for them. When I started up Inventor, the Content Center was still empty. How can I use the libraries? I suspect Inventor is not reading them because they are Inventor 2010 libraries, but I am unable to use the Update Tool - it appears greyed out.
we have Inventor prof 2012 lisc copy ,now we recd 2013 upgrade copy , as per discusswith local service provider of Autodesk need to uninstall whole 2012 and reload fresh 2013. i copied contenet center folder on other location and reload fresh Inventor 2013.when i installed it it is obserbed that content center libraries don't have standards which contents in Inventor 2012. To open our old projects we need this standards, the procedure to import this content center libraries from 2012 to 2013.
View 1 Replies View RelatedWhile using the frame generator's "Trim - Extend to Face" command on short members, the wrong end of the member is being trimmed. Is there a way to choose which end to trim on short members?
View 9 Replies View RelatedHow to use frame generator in assembly? I find difficult to assemble a huge assembly.
View 1 Replies View RelatedI'm running Inventor 2013 professional and I want to design a steel structure for stress analysis. But I can't find any DIN H-beams (HEB, HEA in accordance to DIN 1025) in the "insert frame member selection".
Isn't it possible to use DIN H-beams in Inventor frame generator? Can I add my own parts to the library for stress analysis?
All of a sudden I can't get up my frame generator. I click into my frame > hit "insert frame", which is normally where the dialog box comes up, but I get nothing.
Inventor Professional 2014.
Windows 7 64 bit.
I just recently had Inventor 2012 installed on my computer and I went to make a frame generator and an error message popped up and won't let me make the generator. I attached a .jpeg to this that shows what error keeps appearing.
View 3 Replies View RelatedComing from a solidworks background, i frequently use weldments, or Inventor's equivalent - frame generator.
Wondering if there was a solidworks 'end cap' equivalent.
[URL] essentially a weldment driven and generated part which doesn't need much thinking about.
It seems to me that there is a major disconnect between using the Vault and using Frame Generator. When creating a frame using frame generator all the parts are automatically named by frame generator. It gives you a name such ANSI W8x13 00000001 for an I-beam for instance. As you create more components (I-beams in this case) the number on the end of the file name increases so you have 0000002, 00000003 etc. After I'm finished with the assembly I will check it into the vault.
The issue comes up when I go to create a new assembly a few days later using the same I-beam. The naming convention for the I-beam is exactly the same for the new assembly file. It will start over and give me a new ANSI W8x13 00000001 file. Now when I go to check it into the vault I get the "cannot check in due to vaulting restrictions" error because the two files have been named the exact same thing. It seems crazy that Inventor would be set up this way considering how vault works. The only thing I have found is that you can click the browse button and rename the file. This is a serious headache though because I have to come up with a unique name (or pre-fix) for EVERY part of EVERY frame that I generate. And lets just say it's not hard for me to create 100+ new parts a day using frame generator.
Aside of beams and so I could use some metal studs. Seems like there are not any.
View 9 Replies View RelatedThe frame generator gives the wrong cut length (G_L) when using double end treatment "Trim and Extend to Face"
See attached screen shot: The correct length of the diagonal RHS should be 1852 mm after trimming the RH end to btm and rh member. As far as I remember this is an old problem never been fixed. Is a lot of work manually altering the cut length of 20-30 member in the BOM.
I created a frame using 150 x 75 BS4 channel section in 2011/12 (can't remember which) however it was created before the BOM length fix (all lengths stated are not necessarily the lengths of the beams). In order to fix this I need to redraw the frame, which is fair enough, however I am unable to find the BSI standard channel section. In fact, BSI has seemed to vanish from my library completely, I can not even place a component from the BSI library.
I have had a look around the C:/Programdata/autodesk/inventor2011(or 12 or 13)/contenetcentre/libraries and have found parker, gost, DIN etc but no BSI. I have not used the frame generator/place component in 2013 yet so no idea if this was from install or not.
My skeleton has lost translation with my frame generator and has offset the sketch. I have tried "Edit with Frame Generator" but the peices seem to stay in place.
View 4 Replies View RelatedI have been playing around with Inventor (moving across from Solidworks) and am wondering how I 'detail plates' I am becomeing familiar with the Frame Generator to create all of my members, but it seems quite disconnected in the creation process create a plate.
I currently am creating the 3D sketch (in a part) creating the (base) plate in the same part and then in the assebley I am using the frame Generator (See image) to create the members.
How to correctly include the plates as part of the design process.
Is there any way in standard inventor to find what sketch is related to a frame generator member?
View 6 Replies View RelatedI`ve modelled a pipe and would like to know if this type of pipe can be added to the content centre so as i can use with the frame generator?
View 5 Replies View RelatedHow do you have the frame generator "point" to a custom parts directory to create from?
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
Can i use frame generator and do subassembly using one of the member and still be able to stretch the frame?
will the subassembly stretch as well?
inventor 2011
vault 2012
Recently the company bought a single license of Inventor to test out and see if it meets our company goals and is efficient to use for what we do. I've been working with the frame generator, which is fairly easy to use and make the initial assembly, but I am having trouble and breaking out individual sections to detail.
I am stuck with using LOD for this platform, provide a general workflow procedure of the best way of creating assemblies and subassemblies.
What I am currently using Inventor is to build a condenser platform. Generally we like to weld as much of it in the shop before it goes to the field for final assembly. The platform consists of beam supports, grating, stairs, and handrail. In this case we would generally take sections of the handrail and weld in the shop, we would also have the stairs with the handrail welded on it as well. I would like to refrain from converting this to weldment.
I have tried promoting and demoting but this loses constraints and references. Also I cannot create a single skeleton of the whole frame at one time because a lot of the frame members depend on the other members structural sizes (flange width, height, etc.).
I've read of people creating multiple subassemblies and grounding them, but I would like to think that their has to be away that I could just build off of the base skeleton and not have to cycle through different assemblies.