AutoCAD Inventor :: Publishing Custom Parts Into Content Centre / Frame Generator
Aug 21, 2012
I am trying to create/publish custom shapes into Content Centre and for use in Frame Generator. I can create the i-Part and configure the parameters I want to enable different sizes - no problem. However when I go to "Publish Part" ()
I get the following error.......
do I need to save the ipt file in a different location? What dependencies are there? I get the same result if I follow the Inventor tutorial using the brace.ipt part....
View 2 Replies
ADVERTISEMENT
Oct 16, 2012
I have been trying to add my own shapes to the Content Centre, with some success, but for being able to use them in Frame Generator. I was able to Author a new part and publish it to Structural Shapes and it works very well. However when I try to use it in Frame Generator there is an issue that I do not understand. Frame Generator recognises the family and all of the different sizes and materials, but when it come to inserting the part, i get the following message:
I am not sure what this means. The part family is in my own library in a seperate category. I don't know what/where template file needs to be and is that the same ipt file that I used to create the Content Centre part/shape? Do I need to create a new Standard rather than "attaching" it to the AS Standard?
View 9 Replies
View Related
May 1, 2012
I am using a student version of Inventor 2012 to design the FSAE Chassis for our University team this year. I was not able to find suitable geometry for the required tubing to make the chassis. So I found a guide on setting up a Custom Content Center and publishing parts. I have followed that. The Chassis has turned out great but now I am trying to draw it up and the BOM is not populating as desired.
A Summary:
-Custom Project file with Read / Write Library added.
-Custom tubing geometry created and published to the Library.
-Chassis constructed using standard Frame Generator techniques.
Previously I had the chassis modelled using standard Content Center parts and the BOM would populate with the individual tubes in the drawing environment. Now with the custom tubes the BOM calls up each of the individual tubing sizes, ONCE only and has large quantities. The automatic "Measure" Column is also populated with "*Varies*".
In the Frame Generator wizard each tubing size has come up as it's own "Family".I believe this is because I have published the different part sizes individually. I am guessing I should have published only the one active part but with variable geometry selectable in the "Size" drop down?
I have tried forcing the assembly into the "All Levels" view with the Bill of Materials pop-up in the Assembly environment, but even this is not populating correctly.Something else I have noticed is the individual tubes are using a different naming convention in the model tree.
View 6 Replies
View Related
May 25, 2011
We have invested much time in creating custom content center family tables based on exisiting ANSI tables, etc. so that we can suppress sizes and shapes we do not use and have the descriptions and stock numbers show up both so BOM and parts lists will roll up identical parts and as our purchasing department requires.
We have just discovered, however belatedly, that while these custom tables function just fine when placing an individual part, frame generator apparently does not see these and gets it's info from somewhere else. I have seen a similar post which references an McadForums post, but the link provided is dead.
[URL]....
How to point frame generator to customized CC familes?
View 9 Replies
View Related
May 22, 2013
After using Custom Profile for Frame Generator, the Part List will show total length, not individually. How to split these frame members?
View 2 Replies
View Related
Apr 30, 2013
After using Custom Profile for Frame Generator, the Part List will show total length, not individually. how to split these frame members?
Inventor Professional 2013 SP1.1
Windows 7 Pro 64-bit, SP1
HP EliteBook 8460w; 8 GB RAM; i7 - 2.0 GHz; AMD Firepro M3900 -1 GB
View 2 Replies
View Related
Jul 25, 2010
I typically use basic ISO fastners in conjunction with the bolted connection generator. Just now I have discovered the ability to add a custom library to the content centre. This appears fantastic as I no longer have to sift through the 10 - 30 or so items available in each category to complete my bolted connection.
However I am experiencing a delima
I have created a custom library called "My Favourites" and it contains 6 bolt families, 1 spring & flat washer family and 1 nut family. All families are derived from the ISO standard (bar the spring washer which is DIN 128) and all thread pitches for the respective nut and bolt connection(s) match.
The problem I am experiencing is when I execute the bolted connection command I can add the bolt, 2 flats and 1 spring washer yet when I come to close the connection with a nut the nut selection box is empty?
I have the active project configured with "My Favourites" "Inventor Feature" & "Inventor Routed Systems" as the only in use libraries. Secondly, I have verified the existance of the nut(s) in "My Favourites" in the Content Centre Editor.
I am using Inventor 2010 updated to SP3 on a standalone machine, running Windows 7 Ultimate (w/ latest updates)
View 2 Replies
View Related
Jan 10, 2013
I want to find a rectangular flat section of about 250x200cm and a 150x100cm.Is that possible?
I have the content library of ANSI,JIS,GB,ISO and DIN but i can't find anything in these libraries.
View 3 Replies
View Related
Nov 6, 2011
I had Autodesk Inventor 2011 installed for a while, and then installed some other programs (3DS, Maya and Showcase). This caused all of my add-ins to disappear from Inventor. I managed to get them back, but now when I click the 'Insert Frame' button, I get the followin gerror: [WARNING] Problems encountered while executing frame insert command. [ERROR] Failed to read data from Content Center. [ERROR] Content Center server query failed. check your Content Center configuration to make sure all required libraries are present or check Content Center connectivity to server. I've reinstalled Inventor and reinstalled the content center libraries and the error message is still there. The content center configuration in Application Options seems fine.
View 8 Replies
View Related
Jun 4, 2013
We have customized the Content Center for Wide Flange Beams to produce BOM Descriptions that match company standards. They work beautifully until Frame Generator is used. Frame Generator just seems to do whatever it feels like doing. eg. A simple 4-sided frame made from W6X12, will produce parts with different BOM descriptions and different part numbers even though these fields are populated using expressions in Content Center. Parts of the BOM Description are formatted using the Custom Property Format in the parameters of the Family Template in Content Center. This formatting is followed at times and ignored at times.
We are using Inventor 2012 SP2, Build 219
View 1 Replies
View Related
Apr 2, 2012
What would cause my frame generator parts to rotate when I change a completely different part on my frame. they seem to be off by a very small amount. they seem to rotate everytime a change something else in the frame and can change them to be correct.. I believe my main sketch is constrained.
inventor pro 2012
windows 7 64 bit.
Dell t1500 i7 8 gb ram
ati firepro v4800
View 1 Replies
View Related
Jan 25, 2012
I am on inventor 2010. never really used the frame generator much before. so I may be doing soemthing wrong.
But I just make #d sketches, and add members as i need them.
But I have this assembly, made of I-beams and HSS. I noticed eventually some parts will get twisted.
(Not really sure when and why it happens. I Usually notice just by chance.)
The only way I found to correct the problem is to delete the member and re-add it.
View 2 Replies
View Related
Sep 28, 2013
I'm using Inventor 2014 with Service Pack 1 with Desktop Content Center enabled on a single machine. I've also installed Vault Basic 2014 on the same machine. Operating System is Windows 7 Professional.
I've edited my non-vaulted and vaulted project files to create a Custom Content Center Library called Zzyzx. I've started a new Assembly and entered the Content Center Editor to add files to the Zzyzx library. I've copied the Inventor ANSI fasteners section into the Zzyzx library, using the Copy To method with links enabled. So far, so good.
After copying the entire Inventor ANSI fasteners to the Zzyzx library, I created a new column called DESCRIPTION within the Heavy Hex Head Bolt - Inch series folder. Using and expression, I've modified the string values of the just created DESCRIPTION column. I've elected to map DESCRIPTION to the Project.Description iProperty. I use the OK button and each row in the new column gets populated. Update Lightning Bolts are displayed at the far left of the dialog box.
I then use either the Apply or OK button and then Inventor displays a Publish Error message box that states: Non-unique filename(s) found in members. I've checked the file names and I see nothing that's repeating. I've tried using a new file name, but that doesn't solve the issue.What steps must I take in order to successfully edit my Custom Content Library called Zzyzx?
Inventor 2012 Certified Associate
AutoCAD 2012 Certified Associate
Product Design Suite Ultimate 2012, 2013 & 2014...Other than THAT, Mrs. Lincoln, how was the play? Where we send more Govenors to prison, than on to retirement!
View 1 Replies
View Related
Sep 12, 2013
I'm making a customized content center library for my company and I'm trying to add a special type of nut but I'm not having any luck. I finally figured out how to author a part and have it show up in the bolted connection tool. Now I'm just getting an error as soon as I select my custom nut.
The error is "Cannot initialize part data table. Please verify the table definition in Content Center editor."
I've attached my part. It's a simple nut for use in aluminum extrusion, the only thing that changes between sizes is the threaded hole.
View 7 Replies
View Related
Oct 6, 2011
How do you have the frame generator "point" to a custom parts directory to create from?
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
View 1 Replies
View Related
Aug 5, 2011
I have resorted to partially recreating frames.
I am working on one frame where I have rebuilt two parts multiple times and they still revert to being rotated slightly after performing a rebuild. I can continually hit the rebuild button and watch them rotate back and forth. Is there a known fix for some of these oddities with FG?
Notice the two tubes in the attached pic. I do not understand why they continue to rotate out of alignment after they are placed correctly. (They even look fine when placed.)
Inventor Pro 2011
View 2 Replies
View Related
Mar 2, 2012
I dont know if this is possible or not. What it is, is that we use skeletal modelling, so we use intelligent "master sketches". Now we are just starting to use frame generator also and we want to combine the 2 methods.
An example of how we work is this.......
Lets say, we are designing the base of a basic frame. Now, we sketch in the profile of the RHS that will run along the front of the base and we also sketch in the elevation view of this RHS (see snip 1). This gives us 2 sketches to derive in to create a new part of RHS.
If I change the size of the profile of the RHS within the "master sketch" the newly created RHS part will update to suit. This also applies if I change the length of the RHS within the elevation view within the "master sketch".
So, now we want to add in a 5mm thick plate that sits flush with the top of the RHS, we sketch in a 3mm thick rectangle and make the top line colinear with the top line of the RHS profile sketch (see snip 2). We would then derive through these sketches and use them to create this plate as an ipt.
So now we have 2 parts, 1 length of RHS and 1 piece of plate. If we place these to parts into an assembly and ground them to their "root" then the plate will be sitting flush with the top of the RHS.
If I change the profile of the RHS to 50mm taller in the sketch, then the plate will move up to suit and stay flush with the RHS in the assembly.
NOW, what we want is to use frame generaotor along side this method. Instead of deriving through the first 2 sketches to create the the RHS, we want to create the RHS using frame generator and the elevation sketch BUT what we also want is when we change the profile sketch of the RHS, the Frame generator generated part updates to suit the altered sketch. The reason we want this is because we control all our full assemblies using sketches.
Lets take the same bunch of aforementioned sketches and create the parts using FG.
So I have the RHS profile sketched out at 100x50 and the plate sketch sits colinear with the top of this.
I then go through the motions to create the RHS within FG.
I choose RHS from the drop down menu, then choose 100x50 from the "size" drop down menu. I then use the elevation sketch to specify the length.
Now if I increase the size of the RHS (to 150x50) within the sketch, the plate will move up to suit BUT the actual part of the RHS which was created using FG will still stay the same size (100x50), and the plate will be shown as floating within the assembly!!!
If I do it the other way, i.e. change the size fo the RHS within FG, then the sketch will still show the original size and the plate will still sit flush with this original size. This will show the plate as sitting too low in the assembly!!!
Is there anyway at all, that we can link the profile sketch dimensions to the FG generated parts, so that if we edit the profile size of the RHS to a larger or smaller size then FG will automatically alter the generated part to suit the profile sketch???
Is this at all possible???? Or will we just have to alter both the sketch AND the FG part? We really don't want to use adaptive parts within our assembly, we always just control our assemblies with our "master sketches".
View 2 Replies
View Related
May 27, 2012
In previous versions, as clunky as it was, I used to put a work plane in the centre of a frame generator part using "G_L/2"
This does not seem to work anymore in 2013.
Inventor Professional 2014.
Windows 7 64 bit.
View 1 Replies
View Related
Sep 18, 2013
I'm trying to find out whether I can create custom frame generator profiles in IV2014. Any solutions that I've come across aren't viable (referencing files that don't exist on my machine etc).
View 4 Replies
View Related
Jan 26, 2012
My custom library works fine when I try to insert a part from content center, but when I try to use frame generator my library is not seen. I set the "Standard Organization" and "Standard" family property fields both to "DYNA" hoping that standard would show up in the frame generator "Standard" drop down menu but it doesn't.
I saved a copy of a pipe family to "My Library" and made it an independant family.
View 1 Replies
View Related
Feb 6, 2012
I would like to know if there is a way to suppress size in a custom table for frame members. So far, I've copied the ANSI hss square tube library to another name and it is not linked to the previous family. What I need to do is make only certain size of these tubes available and the only way I found was to delete them. The things is I don't want to delete them because I may need them in the future. Also, when I have different materials in that table they appear as 2 diferent size in the frame generator insertion window. For example, if I have in my table a 2x2x1/8 tubing 1 in aluminum and the other in steel, I will have 2x2x1/8 X2 in the size selection window.
View 6 Replies
View Related
Jun 20, 2012
I recently started to publish custom profiles in my Content Center.
What I wanted to do is to add a custom profile to content center and use it in frame generator. The problem is that I want to write in my Stock Number iProperty the Ordering number of the profile type and the generated length. I did everything in the content center publisher, but somehow it dosent work. It always writes my published file length. I can see that Inventor has the tools to do this, but somehow it dosen't work.
Inventor 2012
Win 7 64-bit
Dell Precision T5400
Intel Xeon 2,5 GHz
8 Gb RAM
NVIDIA Quadro Fx 3700
View 9 Replies
View Related
Jul 12, 2013
[URL] ...... I have a large frame (beams and columns) made up of W shape structural steel. (10x19 and 10x26 mostly)
I need to create notches with some more clearance between the beams. Apparently you can create custom notch profiles, but I can't figure out how to do this with these members (normal content center beams) - everything I am finding is showing people creating custom beams from scratch.
Ideally, I can create one notch profile and apply it to all the beams - because I don't want to create 150 different profiles. So is it possible to add a notch profile to existing content center members?
Here is my frame - there will be lots of notching at the beam intersections.
Here is an intersection - I would like at least 1/8" clear between the edges of the intersecting members.
View 6 Replies
View Related
Sep 27, 2012
I am trying to replace a custom part - created from a content center part - with a copied part with a different name. (I am using the replace tool in an assembly.) However, Inventor is not replacing the part with the part I pick but rather the content center version of it.
View 3 Replies
View Related
Feb 22, 2013
Up until now, for FG I've always created a part with just a sketch in it. I insert that in an assembly and use it as my frame generator driving part. Now, I've started creating a solid instead of just a sketch in the part and using its edges to attach frame members. Picture a cube. I really need to put sheet metal on the cube and have my frame on the outside of the sheet metal. I was setting up a parameter for the sheet metal thickness and offsetting the members in Frame Generator that parameter. Now, I've accidentally discovered that I can select the outside edge of the sheet metal part to attach my frame members to. Is that a valid workflow? If it is, its a bit of an epiphamy for me. Using a parameter in FG as an offset required me to edit each member with FG and update it to get the offset to use the current parameter value.
View 2 Replies
View Related
Oct 9, 2013
I'm trying to make a drawing of a assembly, and some of the parts were made in frame generator. When I try to make a section view the parts made in frame generator still show as whole instead of halved. Is there something that I need to toggle or vice versa so that this will not happen anymore?
View 4 Replies
View Related
Jan 6, 2014
I created a custom profile, IS34, and published it successfully as a structural shape for the frame gererator. My problem is I get an error when I try to use the notch command in frame generator between two of these frame members. I have tried creating a custom notch in the profile definition, but this did not work either. I expected one profile to counter-profile the other.
IS34 Profile
IS34 Frame
Error
I am using Inventor 2013.
View 5 Replies
View Related
Mar 18, 2013
I want to update a frame generator shape so it shows as a phantom part and won't show on the parts list. I don't know how to do this. Would I re-publish this part again? I can't just change the BOM properties in the original part file. What's the best approach here?
View 4 Replies
View Related
Feb 1, 2012
I have a bunch of custom shapes I use in the frame generator and I want to transfer them to another computer. Where are these located and how would I transfer them? I'm using Inventor 2012.
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
View 7 Replies
View Related
Feb 21, 2013
When inserting a content center part for which we have to choose a material, we would like to have a custom material as a default (material with name: "No material selected"). So when selecting no material for this part (for example when the user forgets to select a specific material), the default material (in this case material "No material selected") will be active. In this way, we can see in one view across the BOM which parts have no material assigned yet.
How can this be achieved in the content center (editor)?
Product Design Suite 2014
Inventor 2014, Vault 2014
HP Workstation Z220
Intel Xeon 3.4GHz
16GB RAM
Nvidia Quadro 4000
Windows 7 Professional (64bit)
View 2 Replies
View Related
Jan 28, 2013
I can publish a part containing a user text parameter to the content centre for use in frame generator however when I go to insert that part an error as per the attached screen shot.
To re-create the error you have to follow the below steps.
Create a part with a text user parameterPublish for use in frame generator.Create frame with the part and an error will be created as per the attached screenshot.
Is there a way to work around this error being created and use parts with text user parameters in Frame Generator?
View 5 Replies
View Related
