I made a half section view and it cuts what's above the plane of section in the Z direction, i mean all that's above this plane.
I want it to cut everything that's underneath, below the plane, at my choice, so i can inspect everything what is above the plane of section.
Ray tracing disables when I use the half section view, when I turn it on again it disables the section view. Is there any way I can see a cross section of my assembly in realistic mode with ray tracing?
View 3 Replies View RelatedCannot inspect, export pictures, constraint while in half section (or other) view mode...
View 6 Replies View RelatedI can't sem to get a Half Section View through extruded Content Center parts such as channels, pipes etc.?
View 5 Replies View RelatedI have created a linetype with the text GAS OPTION in it. The line is continuous with a break around the text. In a straight line the linetype works fine (breaks around the text etc). However, when I use a polyline and spline the line for a curved line the text aligns with the direction of the line at the start, but when the line bends, the text suddenly changes direction and reads in the opposite direction. It looks like AutoCAD is trying to keep the text upright rather than following the direction of the line. When the text changes direction it also changes its insertion point and overlaps the continuous part of the line. I have 2013 AutoCAD.
Here is the string I used for the linetype.
*GAS_Option_LINE,Gas line ----GAS OPTION----GAS OPTION----GAS OPTION----
A,8,-15,["GAS OPTION",STANDARD,S=2.54,U=0.0,X=-2.35,Y=-1.27],-12
I am having an issue in trying to get my hole axis to offset in the opposite direction. In the image below I want the slot to be centered on the hole. I can get it to offset moving the slot to the left, but can't get it to go to the right. I have tried a negative number, but both positive and negative move it to the left.
View 7 Replies View Relatedhow to make the fillets goes the opposite direction.I want the fillets to round the edges not join the edges together
View 6 Replies View RelatedI made internal gears with design accelerator.
It's calculation is OK. And drag it,the rotation is good, But the direction is opposite. The tooth's move opposite direction to each other.
I used Autodesk Inventor 2013, And sp2, update DL22436649.zip But, this appeard before And after sp2 patch.
I have cut several sections at different points along a road alignment. The sections are cut facing the same direction as the alignmnet. Is there a way to reverse the section direction without changing the alignment direction?
View 6 Replies View RelatedIn an assembly, i make a half section view, but i want the other side to be seen.
I want only to change the direction of the view, how can i do that?
I have been a long time user of Photoshop Elements, I think since version 2 or 3. I went from 6 to 10 earlier this year and have been working with a Trail version of 11 for a few days now. Overall, I like it, but like so many companies do, when they address a major concern of a large group of customers, they go too far in the opposite direction.
Two major complaints about PSE up through 10 are that it is A) too dark and B) the control icons/text are too small and difficult to see. This is mostly a complaint of the visually impaired. (Which is an interesting side-discussion, given that photography is a visual art).
Although I liked the dark layout, I tended to agre with most users about the latter complaint. The icons and text were difficult to see even for people with good vision. With PSE 11, I see the exact opposite, the layout is too bright for my tastes. After all, the purpose of this software is to work with images. A dark layout lets me focus on the image itself, and not be distracted by the controls.
That much I can adapt to, but the bigger problem is the screen real estate taken up by the Tool Options. It's HUGE! Especially when working with images in a vertical format, which represent a significant percentage of my images. For example I love to play around with vertical panoramas, an often overlooked way to capture a scene such as tall trees, buildings, etc.
I am finding myself constatnly havign to toggle back and forth between the Tool Options bar, and even with the F4 keyboard shortcut, it's a pain in the butt.
my opinion is that Adobe fixed a couple big problems for a lot of users but went too far and created a different set of problems for many other users.
I'd like to see an option between dark and light layouts. Let users decide. Kinda like making the program skinnable, but not all that many options are needed.Or... how about an auto-dimming feature? When the mouse is hovered over the image area, while working with the various tools, automatically dim the surrounding panels and menu bars. Then, when you move over the panels and menus, they would return to normal.Second, find a better solution to the Tool Options bar. Either make it A) moveable, like the other panels, B) resizeable, or C) auto-hide it.
At this point, I've almost decided that the size of that Tool Options Bar is a deal breaker and I won't upgrade. Vertical real estate is hard enough to find on computer monitors and Adobe took up 25% of what little I had. I'll wait for a future version to see if they take it back the other way.
The section view behaves strangely with the ‘section participation: none’ components
Invertor2012 sp2
Win7 x64
why my section is not parallel with my section line. I did constrain my section line in the section line sketch.
View 2 Replies View RelatedIs it possible to set a clone source point which moves in the opposite direction of the cloning route?
View 4 Replies View RelatedIs it possible to have the parent view for the section in one drawing and the child views in another drawing?
View 2 Replies View Relatedhow to show section view in base view with out projection the component.
View 2 Replies View RelatedI have a long shaft with parts mounted on. i want to section it and show the parts. i don't need to show the whole length of the shaft.
I know i can crop the isometric view, but this way i will not see the key hole which is on the other side, it's hidden.
If i make a section it 's in an orthogonal view only.
I want to make the section view, but later to transform the sectioned view to an isometry. is it possible?
Is there a way to save a section view in the assembly as a view rep? Am using 2011.
View 9 Replies View RelatedIt's possible to do a cut view with the cup part with a different view style from the other "not Cut" half.
I achieve that, whit the cut view + normal view croped hover the cut view... but this isn´t a accurate process...
Autodesk Factory Design Suite Ultimate 2014
Autodesk Simulation Mechanical
Autodesk Simulation CFD
Windows 7
I place the first view in a drawing and want to be sectioned.
Is there a way to do that, since when i mark the section line, another view is created.
Or should i put the main view outside of the paper boundaries?
I'm currently working on a cross section plan and was wondering if there was any way I can change the direction of the cross section view. I'm currently just using 2 sample lines, so just 2 views are needed. My problem is that it seems like one cross section...the view is facing upstream and the other sample line, the cross section view is facing downstream.
Is this normal? How come both cross sections don't face the same direction? So with one x section it's in a East-West direction but the other is a West to East direction.
HP Compaq 8100 Elite
Win 7 Pro SP1 - 64Bit
8GB RAM
i7 860 @ 2.80 GHZ
AutoCad Civil 3d 2012 SP1
I need an urgent solution to my issue.I have created section view from a sketch (a line constrained to the projection of a work plane) from my derived part to my drawing using the "Get model sketches ". When i update the iassembly and update the the view using model state the view tries to update but throws an error see attached document.When i delete the section line and create a section line manually ie. by creating a normal sketch in the drawing the same model gets updated without any error.
View 6 Replies View RelatedWhen creating a section view in 2014, the new view now comes bordered by a large box that is hatched. I can hide the borders (4 separate lines) and the hatch but cannot change the size of the view border. I don't remember this from 2011.
View 3 Replies View RelatedI was wondering in inventor 2010 how to create a 3d model section view of a 3d model assembly or if its even possible.
View 5 Replies View RelatedI am trying to produce a section view of a vessel. Inventor makes the section just fine except it is incomplete. See images below:
In the past when I have encountered this issue I would simply locate the part in the browser, Right click on it + Section Participation + section. That usually solves the issue. This time it is not working.
While sectioning an assembly in .idw file, I dont want to see any thing that is behind the section line.
I am not talking about hidden lines. (I can switch of the hidden lines).
Some times, there are holes or opening while sectioning. Thru those openings, some of the parts that are behind the section planes are visible. I dont want to see anything.
How to do it? I am using INV2013.
Options like,
Option 1: Dont view anything more then 0.00mm or 1 mm behind. (Like section depth or view depth which can be entered)
Option 2: Switch off that are not sectioned.
If you have a section view, shafts are typically turned off for segtioning, however there is sometimes detail such as keyways or oil holes that are required to be shown which is where a breakout, view is req'd, however it appears the only way to do this is by creating a detail view first, leading to the possibility of a lot of clutter on the drawing from detail views, as when a breakout view is created on the section view, the shaft will not participate in the breakout.
View 3 Replies View RelatedI am generating a drawing file in inventor.its having lot of sections and projected views. Its not able to accommodate all the views in one sheet. So my plan is to move the section views to second sheet or third sheet but section cutting line has to be in first sheet plan view.
I have seen drawing generated in inventor in same way but don't know how to do it.......
Inventor Professional Suite 2010
Windows 7
In an idw of an assembly, I have made a section view and gave it a distance of 10in expecting to only view my assembly 10 in from the section line.
However, all I get was a slice 10 in deep from the top, my section view wasn't looking at the full height of my assembly.
I started a new print, inserted the same model and the same thing happened. This is only occuring with this model, other models are working just fine.
IV2012 sp1 Win7 x64
inventor 2012. for instance for a aux. view if it is not in-line with the parent view it puts a section line. is there a way to have a single view arrow?
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
I created an assembly with screws and nuts which are not from content center. When creating a section view on Drawing, screws and nuts are also sectioned, but I don't want to.
Is it possible to see entire screws and nuts in a section view?