It's possible to do a cut view with the cup part with a different view style from the other "not Cut" half.
I achieve that, whit the cut view + normal view croped hover the cut view... but this isn´t a accurate process...
Autodesk Factory Design Suite Ultimate 2014
Autodesk Simulation Mechanical
Autodesk Simulation CFD
Windows 7
Is it possible to have the parent view for the section in one drawing and the child views in another drawing?
View 2 Replies View Relatedhow to show section view in base view with out projection the component.
View 2 Replies View RelatedI have a long shaft with parts mounted on. i want to section it and show the parts. i don't need to show the whole length of the shaft.
I know i can crop the isometric view, but this way i will not see the key hole which is on the other side, it's hidden.
If i make a section it 's in an orthogonal view only.
I want to make the section view, but later to transform the sectioned view to an isometry. is it possible?
Is there a way to save a section view in the assembly as a view rep? Am using 2011.
View 9 Replies View RelatedI place the first view in a drawing and want to be sectioned.
Is there a way to do that, since when i mark the section line, another view is created.
Or should i put the main view outside of the paper boundaries?
We have a project where the alignment is not in the center of the section (it's along one edge of the project), but we want the Title Annotation ("STA. 165+00") to show up in the center of the sections.
If you choose "Center" justification in the style, it "centers" it about the zero offset, which in our case is actually the left side.
Is there any way to truly center this call, short of turning it OFF and manually creating separate labels?
Unfortunately, I can't use "Center" and give it a "Y" offset, because the alignment does vary slightly (±30 feet) within these 250' cross sections - which would cause the label to vary by that much also...
I've been having the issue with code set style and making the section view to look the way I want. I created a new code set style and it shows perfectly the way I want in the assembly. When I create the section views, I specify the sections to have the same code set style, but for some reason, it shows up in a different color.
I provided an example showing the fence line as an assembly and in section view. For "mysterious" reasons, the color is different in the section view than in the assembly. And I've checked many time in the section view properties and assembly properties to make sure that both are displaying the same code set style.
The section view behaves strangely with the ‘section participation: none’ components
Invertor2012 sp2
Win7 x64
why my section is not parallel with my section line. I did constrain my section line in the section line sketch.
View 2 Replies View Related1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
how to create a section view for a pond other than quick view.
View 2 Replies View RelatedWhen making a Section view from a Base View is there a setting to make the text follow the Text Style and Paperspace text size. Everytime I create a Section View I have to change the text settings in the Properties box.
View 3 Replies View RelatedI need an urgent solution to my issue.I have created section view from a sketch (a line constrained to the projection of a work plane) from my derived part to my drawing using the "Get model sketches ". When i update the iassembly and update the the view using model state the view tries to update but throws an error see attached document.When i delete the section line and create a section line manually ie. by creating a normal sketch in the drawing the same model gets updated without any error.
View 6 Replies View RelatedWhen creating a section view in 2014, the new view now comes bordered by a large box that is hatched. I can hide the borders (4 separate lines) and the hatch but cannot change the size of the view border. I don't remember this from 2011.
View 3 Replies View RelatedI was wondering in inventor 2010 how to create a 3d model section view of a 3d model assembly or if its even possible.
View 5 Replies View RelatedI am trying to produce a section view of a vessel. Inventor makes the section just fine except it is incomplete. See images below:
In the past when I have encountered this issue I would simply locate the part in the browser, Right click on it + Section Participation + section. That usually solves the issue. This time it is not working.
While sectioning an assembly in .idw file, I dont want to see any thing that is behind the section line.
I am not talking about hidden lines. (I can switch of the hidden lines).
Some times, there are holes or opening while sectioning. Thru those openings, some of the parts that are behind the section planes are visible. I dont want to see anything.
How to do it? I am using INV2013.
Options like,
Option 1: Dont view anything more then 0.00mm or 1 mm behind. (Like section depth or view depth which can be entered)
Option 2: Switch off that are not sectioned.
If you have a section view, shafts are typically turned off for segtioning, however there is sometimes detail such as keyways or oil holes that are required to be shown which is where a breakout, view is req'd, however it appears the only way to do this is by creating a detail view first, leading to the possibility of a lot of clutter on the drawing from detail views, as when a breakout view is created on the section view, the shaft will not participate in the breakout.
View 3 Replies View RelatedI am generating a drawing file in inventor.its having lot of sections and projected views. Its not able to accommodate all the views in one sheet. So my plan is to move the section views to second sheet or third sheet but section cutting line has to be in first sheet plan view.
I have seen drawing generated in inventor in same way but don't know how to do it.......
Inventor Professional Suite 2010
Windows 7
In an idw of an assembly, I have made a section view and gave it a distance of 10in expecting to only view my assembly 10 in from the section line.
However, all I get was a slice 10 in deep from the top, my section view wasn't looking at the full height of my assembly.
I started a new print, inserted the same model and the same thing happened. This is only occuring with this model, other models are working just fine.
IV2012 sp1 Win7 x64
inventor 2012. for instance for a aux. view if it is not in-line with the parent view it puts a section line. is there a way to have a single view arrow?
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
I created an assembly with screws and nuts which are not from content center. When creating a section view on Drawing, screws and nuts are also sectioned, but I don't want to.
Is it possible to see entire screws and nuts in a section view?
Ray tracing disables when I use the half section view, when I turn it on again it disables the section view. Is there any way I can see a cross section of my assembly in realistic mode with ray tracing?
View 3 Replies View RelatedI often do section views in my 3D model (not drawing) to visually check interference, etc. I noticed today that some parts are excluded from this and do not get sectioned. I'm sure it's an easy fix but a search turned up nothing. How do I include/exclude specific parts from this view?
View 2 Replies View Relatedhow to cut those three portions instead of my full-section view.I have a dimensioning problem with this second radius which inventor refuses to create even it detects that it's a fillet feature. also how do I resize the dimension text.
View 3 Replies View Relatedwhat the check box in the options for 'section view as uncut' does ? see attached screenshot.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
In inventor 2013 professional I have a problem using the section view in my assemblies files. When I active the section view it works well, as soon as I open a command (for example the measure of a distance) the section view disappear and the assembly appear in entire view.I didn't modified any configuration on my software.
View 4 Replies View RelatedI made an assembly, inserted a bolt and saved it to another file for thee modifications i make in the screw.
I try to make a section view with one of the origin planes, but it doesn't make
In my idw, when I right-click on my section view line (or the section view itself), I want to change the section depth from full to some distance. Problem is there is not a "Edit Section Properties" in the context menu.
There are other section views on this sheet and they will display "Edit Section Properties" in the context menu.
Any clues as to why I dont get a context menu on just this one section view? I could delete the view and redimension everything, but I had rather not.... Its got several dims on it.
Cant post the file either... its pretty large.?The idw itself is 16mb, not counting all the parts/assemblies.
I have a plan view where I want to show the door openings but I want the section view w/ the doors closed. I can't seem to get inventor to do this.
View 1 Replies View Related